- Fix a bug in MAXxxxx thermocouple temp reporting.
- Add support for 3-wire HD44780.
- Add support for PCA9533 RGB driver.
- Add configuration examples for FlashForge CreatorPro.
Implement initial support for MKS Robin (STM32F103ZET6) board.
Custom build script is used to generate encrypted firmware compatible with original MSK Robin bootloader (i.e. safe firmware update from SD card and possibility to go back to original close-source firmware).
-Disable LDF "deep+" mode on AT90USB platforms. Appears not needed any longer (likely due to fix 7322df26ad). Results in identical binary output and cuts compile time in half
-Disable Cartesio config from CircleCI (compile failure)
-Disable Geetech I3 Pro X GT2560 from CircleCI (compile failure)
-Enable EEPROM on Micromake example config (fix compile failure)
-Move FolgerTech/i3-2020 to AVR platform in CircleCI (fix CirculeCI build failure)
-Disable various examples failing to build in CircleCI
-Enable various examples no longer failing to build in CircleCI
* Add traceback after watchdog timeout
Add the cpability to perform a traceback following a watchdog timeout.
* Enhanced hardware SPI
Allow use of either SSP0 or SSP1.
Ensure that no data is left in I/O buffers after calls to enable sharing of SSP hardware.
* Make flash emulation of eeprom the default
Make use of flash for eeprom storage the default. This means that usage of eeprom will not cause USB drive mount/unmount operations.
* Allow sharing of SD card
SD card I/O operations from the USB stack take place in idle loop, rather than at interrupt time. Allowing sharing of the SPI bus.
New configuration options to allow usage of the SD card to be specified.
* Fix problem with hardware SPI pins
Framework and build platform now located at https://github.com/p3p/pio-framework-arduino-lpc176x and https://github.com/p3p/pio-nxplpc-arduino-lpc176x respectively
fix mkssbase leds
move hardware serial
remove hardware/software serial
Hardware Serial extraction
HardwareSerial ISRs
fix disabled serial2 causing Serial object to link
move usb devices out to framework
separate out adc/pwm peripheral function from hal.cpp
fix includes
remove unused pwm init
move adc
HAL header update
templated filtered adc
LPC1769 platform
-Enable boards_dir option in PIO INI
-Remove defunct custom board file operations for PIO auto-build environment
-Remove now-defunct Teensy++ 2.0 PIO entry, replaced by `at90USB1286_DFU` and `at90USB1286_DFU` (using this entry always put AT90USB board boot loaders in jeopardy of being overwritten due to the very small size of the official Teensy++ 2.0 bootloader)
-whitespace
LPC1768 VIKI2 & RRDFG are working
looks like all SPIs are working
library change
sh1106 locks up
fixed lockup, started I2C SW com
pretty
re-org
restore a few files
make library happy
switched HAL version of rrd
fix travis error
travis error fixes
another travis fix
cleanup
minor update
one more
correct spacing in platformio.ini
* Merging early because of build failures. See #8105
* Make LPC1768 pinmapping not specific to Re-ARM
* Add HAL_PIN_TYPE and LPC1768 pin features
* M43 Updates
* Move pin map into pinsDebug_LPC1768.h
* Incorporate comments and M226
* Fix persistent store compilation issues
* Update pin features
* Update MKS SBASE pins
* Use native LPC1768 pin numbers in M42, M43, and M226
* fixed some include paths
* LPC1768: Fix Serial API
Add missing serial methods used if TX_BUFFER_SIZE is set
Change return value of HalSerial:read to match Arduino API
* LPC1768: add filters to ADC
This is to try and compensate for hardware issue and oversensitivity to noise
* LPC1768: remove the polling section of delayMicroseconds
* LPC1768: lock usb mass storage device while device accesses it.
Currently only applicable to persistent store,
The device always has priority and will unmount the sd card from the host, Windows then tries to automount again so it can look like the explorer window freezes. Linux Mint, by default, just closes the Nemo window.
* Add timeout to make sure if Serial never connects that Marlin still boots
* Remove unneeded ifdef CPU_32_BIT
In general the need for ifdef CPU_32_BIT blocks means that something is missing from the HAL API or a Platform, in this case HAL_TICKS_PER_US was missing from the AVR Platform
* LPC1768: relocate RE-ARM debug_extra_script.py
Simon Jouet
Thomas Moore
Bob Kuhn
mikeshub
Chris Pepper
Karl Andersson
Reece Kibble
jmz52
teemuatlut
Dave Johnson
skaaj4
Andy Shaw
Scott Lahteine
Scott Lahteine
forkoz
Roxy-3D
Shen Yiming
Simon Jouet
xC0000005
Yunhui Fu
Alexey Shvetsov
etagle
Johnny Eshak
Ivan Kravets
Thomas Moore
Ralph Schmidt
MTrab
Brian