Config: adjust PLA Temperatures

Firmware will still be loaded from onboard sd card only.

Marlin/Configuration.h

@@ -69,7 +69,7 @@
 // @section info
 
 // Author info of this build printed to the host during boot and M115
-#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
+#define STRING_CONFIG_H_AUTHOR "(Alfred Melch, default config)" // Who made the changes.
 //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
 
 /**
@@ -123,8 +123,8 @@
  * Currently Ethernet (-2) is only supported on Teensy 4.1 boards.
  * :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-//#define SERIAL_PORT_2 -1
+#define SERIAL_PORT_2 -1
-//#define BAUDRATE_2 250000   // Enable to override BAUDRATE
+#define BAUDRATE_2 250000   // Enable to override BAUDRATE
 
 /**
  * Select a third serial port on the board to use for communication with the host.
@@ -139,15 +139,15 @@
 
 // Choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define MOTHERBOARD BOARD_RAMPS_14_EFB
+  #define MOTHERBOARD BOARD_BTT_SKR_V1_4_TURBO
 #endif
 
 // Name displayed in the LCD "Ready" message and Info menu
-//#define CUSTOM_MACHINE_NAME "3D Printer"
+#define CUSTOM_MACHINE_NAME "x301"
 
 // Printer's unique ID, used by some programs to differentiate between machines.
 // Choose your own or use a service like https://www.uuidgenerator.net/version4
-//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
+#define MACHINE_UUID "6b764807-48e6-4e69-ae22-49ffe439ef34"
 
 /**
  * Define the number of coordinated linear axes.
@@ -482,7 +482,7 @@
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  *
  */
-#define TEMP_SENSOR_0 1
+#define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
@@ -490,7 +490,7 @@
 #define TEMP_SENSOR_5 0
 #define TEMP_SENSOR_6 0
 #define TEMP_SENSOR_7 0
-#define TEMP_SENSOR_BED 0
+#define TEMP_SENSOR_BED 11
 #define TEMP_SENSOR_PROBE 0
 #define TEMP_SENSOR_CHAMBER 0
 #define TEMP_SENSOR_COOLER 0
@@ -750,7 +750,7 @@
 
 // Enable one of the options below for CoreXY, CoreXZ, or CoreYZ kinematics,
 // either in the usual order or reversed
-//#define COREXY
+#define COREXY
 //#define COREXZ
 //#define COREYZ
 //#define COREYX
@@ -821,7 +821,7 @@
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
 #define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
 #define I_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define J_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define K_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
@@ -851,9 +851,9 @@
  *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  */
-#define X_DRIVER_TYPE  A4988
+#define X_DRIVER_TYPE  TMC2209
-#define Y_DRIVER_TYPE  A4988
+#define Y_DRIVER_TYPE  TMC2209
-#define Z_DRIVER_TYPE  A4988
+#define Z_DRIVER_TYPE  TMC2209
 //#define X2_DRIVER_TYPE A4988
 //#define Y2_DRIVER_TYPE A4988
 //#define Z2_DRIVER_TYPE A4988
@@ -862,7 +862,7 @@
 //#define I_DRIVER_TYPE  A4988
 //#define J_DRIVER_TYPE  A4988
 //#define K_DRIVER_TYPE  A4988
-#define E0_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE TMC2209
 //#define E1_DRIVER_TYPE A4988
 //#define E2_DRIVER_TYPE A4988
 //#define E3_DRIVER_TYPE A4988
@@ -924,11 +924,11 @@
  * Override with M203
  *                                      X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_FEEDRATE          { 300, 300, 5, 25 }
+#define DEFAULT_MAX_FEEDRATE          { 300, 300, 20, 25 }
 
-//#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
+#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
 #if ENABLED(LIMITED_MAX_FR_EDITING)
-  #define MAX_FEEDRATE_EDIT_VALUES    { 600, 600, 10, 50 } // ...or, set your own edit limits
+  #define MAX_FEEDRATE_EDIT_VALUES    { 2400, 2400, 25, 50 } // ...or, set your own edit limits
 #endif
 
 /**
@@ -939,7 +939,7 @@
  */
 #define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }
 
-//#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
+#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
 #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
   #define MAX_ACCEL_EDIT_VALUES       { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
 #endif
@@ -1020,10 +1020,10 @@
  * The probe replaces the Z-MIN endstop and is used for Z homing.
  * (Automatically enables USE_PROBE_FOR_Z_HOMING.)
  */
-#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
+// #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 
 // Force the use of the probe for Z-axis homing
-//#define USE_PROBE_FOR_Z_HOMING
+#define USE_PROBE_FOR_Z_HOMING
 
 /**
  * Z_MIN_PROBE_PIN
@@ -1077,7 +1077,7 @@
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
-//#define BLTOUCH
+#define BLTOUCH
 
 /**
  * Touch-MI Probe by hotends.fr
@@ -1169,7 +1169,7 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
+#define NOZZLE_TO_PROBE_OFFSET { -20, 13, -1.49 }
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
@@ -1312,7 +1312,7 @@
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
 #define INVERT_X_DIR false
-#define INVERT_Y_DIR true
+#define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
 //#define INVERT_I_DIR false
 //#define INVERT_J_DIR false
@@ -1321,7 +1321,7 @@
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.
-#define INVERT_E0_DIR false
+#define INVERT_E0_DIR true
 #define INVERT_E1_DIR false
 #define INVERT_E2_DIR false
 #define INVERT_E3_DIR false
@@ -1359,16 +1359,16 @@
 // @section machine
 
 // The size of the printable area
-#define X_BED_SIZE 200
+#define X_BED_SIZE 300
-#define Y_BED_SIZE 200
+#define Y_BED_SIZE 300
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
-#define X_MIN_POS 0
+#define X_MIN_POS -7
-#define Y_MIN_POS 0
+#define Y_MIN_POS -2
 #define Z_MIN_POS 0
 #define X_MAX_POS X_BED_SIZE
 #define Y_MAX_POS Y_BED_SIZE
-#define Z_MAX_POS 200
+#define Z_MAX_POS 320
 //#define I_MIN_POS 0
 //#define I_MAX_POS 50
 //#define J_MIN_POS 0
@@ -1408,7 +1408,7 @@
 #endif
 
 #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
-  //#define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
+  #define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
 #endif
 
 /**
@@ -1527,7 +1527,7 @@
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
 //#define AUTO_BED_LEVELING_BILINEAR
-//#define AUTO_BED_LEVELING_UBL
+#define AUTO_BED_LEVELING_UBL
 //#define MESH_BED_LEVELING
 
 /**
@@ -1535,7 +1535,7 @@
  * these options to restore the prior leveling state or to always enable
  * leveling immediately after G28.
  */
-//#define RESTORE_LEVELING_AFTER_G28
+#define RESTORE_LEVELING_AFTER_G28
 //#define ENABLE_LEVELING_AFTER_G28
 
 /**
@@ -1577,14 +1577,14 @@
   /**
    * Enable the G26 Mesh Validation Pattern tool.
    */
-  //#define G26_MESH_VALIDATION
+  #define G26_MESH_VALIDATION
   #if ENABLED(G26_MESH_VALIDATION)
     #define MESH_TEST_NOZZLE_SIZE    0.4  // (mm) Diameter of primary nozzle.
     #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for G26.
-    #define MESH_TEST_HOTEND_TEMP  205    // (°C) Default nozzle temperature for G26.
+    #define MESH_TEST_HOTEND_TEMP  200    // (°C) Default nozzle temperature for G26.
     #define MESH_TEST_BED_TEMP      60    // (°C) Default bed temperature for G26.
-    #define G26_XY_FEEDRATE         20    // (mm/s) Feedrate for G26 XY moves.
+    #define G26_XY_FEEDRATE         50    // (mm/s) Feedrate for G26 XY moves.
-    #define G26_XY_FEEDRATE_TRAVEL 100    // (mm/s) Feedrate for G26 XY travel moves.
+    #define G26_XY_FEEDRATE_TRAVEL 200    // (mm/s) Feedrate for G26 XY travel moves.
     #define G26_RETRACT_MULTIPLIER   1.0  // G26 Q (retraction) used by default between mesh test elements.
   #endif
 
@@ -1666,7 +1666,7 @@
 #endif
 
 // Add a menu item to move between bed corners for manual bed adjustment
-//#define LEVEL_BED_CORNERS
+#define LEVEL_BED_CORNERS
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
@@ -1727,7 +1727,7 @@
  * - Allows Z homing only when XY positions are known and trusted.
  * - If stepper drivers sleep, XY homing may be required again before Z homing.
  */
-//#define Z_SAFE_HOMING
+#define Z_SAFE_HOMING
 
 #if ENABLED(Z_SAFE_HOMING)
   #define Z_SAFE_HOMING_X_POINT X_CENTER  // X point for Z homing
@@ -1735,7 +1735,7 @@
 #endif
 
 // Homing speeds (mm/min)
-#define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (4*60) }
+#define HOMING_FEEDRATE_MM_M { (30*60), (30*60), (4*60) }
 
 // Validate that endstops are triggered on homing moves
 #define VALIDATE_HOMING_ENDSTOPS
@@ -1812,7 +1812,7 @@
  *   M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  *   M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  */
-//#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
+#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
 //#define DISABLE_M503        // Saves ~2700 bytes of PROGMEM. Disable for release!
 #define EEPROM_CHITCHAT       // Give feedback on EEPROM commands. Disable to save PROGMEM.
 #define EEPROM_BOOT_SILENT    // Keep M503 quiet and only give errors during first load
@@ -1846,8 +1846,8 @@
 // Preheat Constants - Up to 5 are supported without changes
 //
 #define PREHEAT_1_LABEL       "PLA"
-#define PREHEAT_1_TEMP_HOTEND 180
+#define PREHEAT_1_TEMP_HOTEND 200
-#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_TEMP_BED     60
 #define PREHEAT_1_TEMP_CHAMBER 35
 #define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
@@ -1868,7 +1868,7 @@
  *    P1  Raise the nozzle always to Z-park height.
  *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  */
-//#define NOZZLE_PARK_FEATURE
+#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
@@ -2085,7 +2085,7 @@
  * SD Card support is disabled by default. If your controller has an SD slot,
  * you must uncomment the following option or it won't work.
  */
-//#define SDSUPPORT
+#define SDSUPPORT
 
 /**
  * SD CARD: ENABLE CRC
@@ -2344,7 +2344,7 @@
 // RepRapDiscount FULL GRAPHIC Smart Controller
 // https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
 //
-//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
 
 //
 // K.3D Full Graphic Smart Controller

Marlin/Configuration_adv.h

@@ -562,7 +562,7 @@
  * Multiple extruders can be assigned to the same pin in which case
  * the fan will turn on when any selected extruder is above the threshold.
  */
-#define E0_AUTO_FAN_PIN -1
+#define E0_AUTO_FAN_PIN FAN1_PIN
 #define E1_AUTO_FAN_PIN -1
 #define E2_AUTO_FAN_PIN -1
 #define E3_AUTO_FAN_PIN -1
@@ -764,7 +764,7 @@
 
 //#define SENSORLESS_BACKOFF_MM  { 2, 2, 0 }  // (mm) Backoff from endstops before sensorless homing
 
-#define HOMING_BUMP_MM      { 5, 5, 2 }       // (mm) Backoff from endstops after first bump
+#define HOMING_BUMP_MM      { 0, 0, 2 }       // (mm) Backoff from endstops after first bump
 #define HOMING_BUMP_DIVISOR { 2, 2, 4 }       // Re-Bump Speed Divisor (Divides the Homing Feedrate)
 
 //#define HOMING_BACKOFF_POST_MM { 2, 2, 2 }  // (mm) Backoff from endstops after homing
@@ -1424,7 +1424,7 @@
   //#define UTF_FILENAME_SUPPORT
 
   // This allows hosts to request long names for files and folders with M33
-  //#define LONG_FILENAME_HOST_SUPPORT
+  #define LONG_FILENAME_HOST_SUPPORT
 
   // Enable this option to scroll long filenames in the SD card menu
   //#define SCROLL_LONG_FILENAMES
@@ -1449,7 +1449,7 @@
   /**
    * Auto-report SdCard status with M27 S<seconds>
    */
-  //#define AUTO_REPORT_SD_STATUS
+  #define AUTO_REPORT_SD_STATUS
 
   /**
    * Support for USB thumb drives using an Arduino USB Host Shield or
@@ -1519,7 +1519,7 @@
    *
    * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
    */
-  //#define SDCARD_CONNECTION LCD
+  #define SDCARD_CONNECTION LCD
 
   // Enable if SD detect is rendered useless (e.g., by using an SD extender)
   //#define NO_SD_DETECT
@@ -2181,7 +2181,7 @@
  * Currently handles M108, M112, M410, M876
  * NOTE: Not yet implemented for all platforms.
  */
-//#define EMERGENCY_PARSER
+#define EMERGENCY_PARSER
 
 /**
  * Realtime Reporting (requires EMERGENCY_PARSER)
@@ -2217,7 +2217,7 @@
 #define SERIAL_OVERRUN_PROTECTION
 
 // For serial echo, the number of digits after the decimal point
-//#define SERIAL_FLOAT_PRECISION 4
+#define SERIAL_FLOAT_PRECISION 4
 
 // @section extras
 
@@ -2358,7 +2358,7 @@
  *
  * Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
  */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
   #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
@@ -2396,10 +2396,10 @@
   #define FILAMENT_CHANGE_ALERT_BEEPS         10  // Number of alert beeps to play when a response is needed.
   #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.
 
-  //#define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
+  #define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
   //#define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
 
-  //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+  #define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
   //#define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
 #endif
 
@@ -2821,7 +2821,7 @@
    * Define your own with:
    * { <off_time[1..15]>, <hysteresis_end[-3..12]>, hysteresis_start[1..8] }
    */
-  #define CHOPPER_TIMING CHOPPER_DEFAULT_12V        // All axes (override below)
+  #define CHOPPER_TIMING CHOPPER_DEFAULT_24V        // All axes (override below)
   //#define CHOPPER_TIMING_X  CHOPPER_TIMING        // For X Axes (override below)
   //#define CHOPPER_TIMING_X2 CHOPPER_TIMING_X
   //#define CHOPPER_TIMING_Y  CHOPPER_TIMING        // For Y Axes (override below)
@@ -2850,7 +2850,7 @@
    * M912 - Clear stepper driver overtemperature pre-warn condition flag.
    * M122 - Report driver parameters (Requires TMC_DEBUG)
    */
-  //#define MONITOR_DRIVER_STATUS
+  #define MONITOR_DRIVER_STATUS
 
   #if ENABLED(MONITOR_DRIVER_STATUS)
     #define CURRENT_STEP_DOWN     50  // [mA]
@@ -2912,7 +2912,7 @@
    *
    * Comment *_STALL_SENSITIVITY to disable sensorless homing for that axis.
    */
-  //#define SENSORLESS_HOMING // StallGuard capable drivers only
+  #define SENSORLESS_HOMING // StallGuard capable drivers only
 
   #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING)
     // TMC2209: 0...255. TMC2130: -64...63
@@ -3564,14 +3564,14 @@
 /**
  * Auto-report position with M154 S<seconds>
  */
-//#define AUTO_REPORT_POSITION
+#define AUTO_REPORT_POSITION
 
 /**
  * Include capabilities in M115 output
  */
 #define EXTENDED_CAPABILITIES_REPORT
 #if ENABLED(EXTENDED_CAPABILITIES_REPORT)
-  //#define M115_GEOMETRY_REPORT
+  #define M115_GEOMETRY_REPORT
 #endif
 
 /**
@@ -3619,11 +3619,11 @@
 //#define NO_WORKSPACE_OFFSETS
 
 // Extra options for the M114 "Current Position" report
-//#define M114_DETAIL         // Use 'M114` for details to check planner calculations
+#define M114_DETAIL         // Use 'M114` for details to check planner calculations
 //#define M114_REALTIME       // Real current position based on forward kinematics
 //#define M114_LEGACY         // M114 used to synchronize on every call. Enable if needed.
 
-//#define REPORT_FAN_CHANGE   // Report the new fan speed when changed by M106 (and others)
+#define REPORT_FAN_CHANGE   // Report the new fan speed when changed by M106 (and others)
 
 /**
  * Set the number of proportional font spaces required to fill up a typical character space.
@@ -3795,9 +3795,9 @@
  * Host Prompt Support enables Marlin to use the host for user prompts so
  * filament runout and other processes can be managed from the host side.
  */
-//#define HOST_ACTION_COMMANDS
+#define HOST_ACTION_COMMANDS
 #if ENABLED(HOST_ACTION_COMMANDS)
-  //#define HOST_PROMPT_SUPPORT
+  #define HOST_PROMPT_SUPPORT
   //#define HOST_START_MENU_ITEM  // Add a menu item that tells the host to start
 #endif
 

platformio.ini

@@ -13,7 +13,7 @@
 [platformio]
 src_dir      = Marlin
 boards_dir   = buildroot/share/PlatformIO/boards
-default_envs = mega2560
+default_envs = LPC1769
 include_dir  = Marlin
 extra_configs =
     ini/avr.ini