6f4873329e
Replace U8GLI v1.11 with v1.17
...
In Travis we already test against 1.17.
10 years ago
764e61708b
Merge pull request #2208 from alexxy/ru_translations
...
Update ru translation
10 years ago
a8670b66a7
Update ru translation
...
Signed-off-by: Alexey Shvetsov <alexxy@gentoo.org>
10 years ago
93da52d011
Added support for OLED SSD1306 I2C based LCDs.
10 years ago
9c09967803
Merge pull request #2149 from Wurstnase/enstop_bits
...
faster compare
10 years ago
0f3f7d6835
clean up double endstops
10 years ago
9d2a980bcf
Merge pull request #2170 from thinkyhead/beep_M600_elsewise
...
Slight size reduction by adding idle()
10 years ago
2728dc0606
Merge pull request #2194 from thinkyhead/reduce_strings
...
Redo "invalid extruder" to save 304 bytes
10 years ago
be5236e839
Reduce setTargetedHotend by removing the switch
10 years ago
06f401e7e5
Redo "invalid extruder" to save 264 bytes
...
- Use `setTargetedHotend` in `M200`, as with other commands that use
`T` for the extruder
- Synthesize the "invalid extruder" message, obviating several long
strings
10 years ago
1a882bcc2e
Merge pull request #2193 from thinkyhead/ignore_unrecognized_commands
...
Ignore unknown commands if they start with G, M, or T
10 years ago
a672872717
Merge pull request #2187 from AnHardt/MAX6675M105
...
Print active extruder with M105 for MAX6675
10 years ago
9beed830eb
Drop commented code_is_good lines
10 years ago
068d4a1eb2
Ignore unknown commands if they start with G, M, or T
10 years ago
5824f613ff
Merge pull request #2185 from jothan/bed_integral
...
Separate the maximum integral power for the bed from PID_INTEGRAL_DRI…
10 years ago
c5c9d12630
Merge pull request #2183 from AnHardt/displayinit
...
Initialize the display earlier
10 years ago
ef4becc413
Merge pull request #2188 from AnHardt/FtoN
...
Replace MSG_F? with MSG_N?
10 years ago
eecabf0b00
Merge pull request #2190 from thinkyhead/new_parser_m33
...
Update M33 for new gcode parser
10 years ago
0564625757
Update M33 for new gcode parser
10 years ago
f18f689c01
Replace MSG_F? with MSG_N?
...
To avoid double definitions.
I prefer to read N for Number not for Nozzle.
10 years ago
af7e3f5076
Print active extruder with M105 for MAX6675
...
Was omitted when T0 is a MAX6675.
10 years ago
d46d9d998e
Add maximum bed integral term in example configurations.
10 years ago
e86f2342c0
Separate the maximum integral power for the bed from PID_INTEGRAL_DRIVE_MAX / PID_MAX.
...
My PID_INTEGRAL_DRIVE_MAX was at 96, which was insufficient for my bed
to reach its intended temperature. The head requires a low maximum power since
I run on 24 volts and it has a somewhat low thermal mass.
10 years ago
a8a8f236d2
Merge pull request #2180 from thinkyhead/fix_radian
...
Fix DEGREES macro
10 years ago
f0523b5816
Initialize the display earlier
...
to have it ready to display errors during (temperature)-setup.
10 years ago
790c697c19
Fix DEGREES macro
10 years ago
76b4678f99
Merge pull request #2171 from thinkyhead/gcode_110_is_good
...
M110 is a known command
10 years ago
03d5709b09
M110 is a known command
...
- The command parser now displays “unknown command” in more cases.
Known commands must be added to the `switch` inside `process_commands`
to suppress the error.
10 years ago
d76a01194d
Slight size reduction by adding idle()
10 years ago
22c8bc5ef4
Merge pull request #2157 from AnHardt/bed-mintemp
...
Activate BED_MINTEMP error
10 years ago
97a48e36e9
Merge pull request #2156 from AnHardt/kill3
...
Call kill() only once when triggered by a temperature error
10 years ago
2deb5a8ac5
Temporary Hack
...
REVERT THIS CHANGE
In proper use, we want to force the vendor to update this file to reflect distribution parameters
However, until most users have converted to automatic versioning,
we “grant them a pass”
10 years ago
b5743d6927
Use SOURCE_CODE_URL rather than FIRMWARE_URL
10 years ago
5ea139fd79
Revised Versioning mechanism
10 years ago
da246f5cb1
Activate BED_MINTEMP error.
...
And call _temp_error() directly for ERR_MAXTEMP_BED to avoid the only one time use of bed_max_temp_error().
Includes #2156 .
10 years ago
959da98d8e
Call kill() only once when triggered by a temperature error
...
to avoid stack overflow when called from interrupt.
Some clean up for calls of disable_all_heaters().
'disable_all_heaters()' is called in kill() and again when 'killed' is already set inside _temp_error().
10 years ago
ffc39dc182
Merge pull request #2153 from thinkyhead/leveling_shrink
...
Reduce code size with out_of_range_error function
10 years ago
68f6f149d0
Reduce code size with out_of_range_error function
...
- Affects code size when automatic bed leveling is enabled
10 years ago
f8aabd670e
Notes about Development in its README.md
10 years ago
94120740d8
faster compare
...
!(~(ab)&0x3) and ab == 0x3 are equal
10 years ago
c9141e604a
Merge pull request #2145 from thinkyhead/gcode_folding
...
Indentation in process_commands
10 years ago
3778362f88
Merge pull request #2143 from thinkyhead/fix_command_parser_M110
...
Cleanup pins in RAMPS_13_EFB boards
10 years ago
b55f8718c3
Indent G90/G91, G92
10 years ago
b0d520b109
Indent G30, G31/G32
10 years ago
ffe27a6225
Indent G29
10 years ago
86083badc2
Indent G4, G10/G11, G28
10 years ago
47d7a9cb5e
Indent G2/G3
10 years ago
350f239d84
Indent G0/G1
10 years ago
672b0c1fd3
Cleanup pins in RAMPS_13_EFB boards
10 years ago
f4584c51c5
Merge pull request #2142 from thinkyhead/fix_command_parser_M110
...
No need for +1 on initial seen_pointer
10 years ago
AnHardt
Alexey Shvetsov
fmalpartida
Wurstnase
Scott Lahteine
Scott Lahteine
Jonathan Bastien-Filiatrault
Richard Wackerbarth