From e61257475917c95c35c631f33c99f2539b45e10c Mon Sep 17 00:00:00 2001
From: Alfred Melch <dev@melch.pro>
Date: Thu, 12 Aug 2021 07:40:34 +0200
Subject: [PATCH] Config: specify installed components

- Temp sensor on hotend
- 4, Stepper drivers: X, Y, Z and E0
- BLTOUCH and offset
---
 Marlin/Configuration.h | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index f0d6c906ca..d517bb9b1d 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -491,7 +491,7 @@
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  *
  */
-#define TEMP_SENSOR_0 1
+#define TEMP_SENSOR_0 5
 #define TEMP_SENSOR_1 0
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
@@ -866,9 +866,9 @@
  *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  */
-#define X_DRIVER_TYPE  A4988
-#define Y_DRIVER_TYPE  A4988
-#define Z_DRIVER_TYPE  A4988
+#define X_DRIVER_TYPE  TMC2209
+#define Y_DRIVER_TYPE  TMC2209
+#define Z_DRIVER_TYPE  TMC2209
 //#define X2_DRIVER_TYPE A4988
 //#define Y2_DRIVER_TYPE A4988
 //#define Z2_DRIVER_TYPE A4988
@@ -877,7 +877,7 @@
 //#define I_DRIVER_TYPE  A4988
 //#define J_DRIVER_TYPE  A4988
 //#define K_DRIVER_TYPE  A4988
-#define E0_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE TMC2209
 //#define E1_DRIVER_TYPE A4988
 //#define E2_DRIVER_TYPE A4988
 //#define E3_DRIVER_TYPE A4988
@@ -1092,7 +1092,7 @@
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
-//#define BLTOUCH
+#define BLTOUCH
 
 /**
  * Touch-MI Probe by hotends.fr
@@ -1184,7 +1184,7 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
+#define NOZZLE_TO_PROBE_OFFSET { -20, 13, 0 }
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.