Merge pull request #553 from iXce/req413

Update #413 for merging, fix languages.h

Marlin/Configuration.h

@@ -28,6 +28,7 @@
 // 3  = MEGA/RAMPS up to 1.2 = 3
 // 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
 // 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
+// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
 // 4  = Duemilanove w/ ATMega328P pin assignment
 // 5  = Gen6
 // 51 = Gen6 deluxe

Marlin/Marlin_main.cpp

@@ -194,6 +194,10 @@ int EtoPPressure=0;
   float retract_recover_length=0, retract_recover_feedrate=8*60;
 #endif
 
+#ifdef ULTIPANEL
+	bool powersupply = true;
+#endif
+
 //===========================================================================
 //=============================private variables=============================
 //===========================================================================
@@ -1390,14 +1394,26 @@ void process_commands()
     #endif
 
     #if defined(PS_ON_PIN) && PS_ON_PIN > -1
-      case 80: // M80 - ATX Power On
+      case 80: // M80 - Turn on Power Supply
         SET_OUTPUT(PS_ON_PIN); //GND
         WRITE(PS_ON_PIN, PS_ON_AWAKE);
+        #ifdef ULTIPANEL
+          powersupply = true;
+          LCD_MESSAGEPGM(WELCOME_MSG);
+          lcd_update();
+        #endif
         break;
       #endif
-
-      case 81: // M81 - ATX Power Off
-
+      
+      case 81: // M81 - Turn off Power Supply
+        disable_heater();
+        st_synchronize();
+        disable_e0();
+        disable_e1();
+        disable_e2();
+        finishAndDisableSteppers();
+        fanSpeed = 0;
+        delay(1000); // Wait a little before to switch off
       #if defined(SUICIDE_PIN) && SUICIDE_PIN > -1
         st_synchronize();
         suicide();
@@ -1405,7 +1421,12 @@ void process_commands()
         SET_OUTPUT(PS_ON_PIN);
         WRITE(PS_ON_PIN, PS_ON_ASLEEP);
       #endif
-        break;
+      #ifdef ULTIPANEL
+        powersupply = false;
+        LCD_MESSAGEPGM(MACHINE_NAME" "MSG_OFF".");
+        lcd_update();
+      #endif
+	  break;
 
     case 82:
       axis_relative_modes[3] = false;

Marlin/pins.h

@@ -298,7 +298,7 @@
 * Arduino Mega pin assignment
 *
 ****************************************************************************************/
-#if MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 77
+#if MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 77
 #define KNOWN_BOARD 1
 
 //////////////////FIX THIS//////////////
@@ -314,7 +314,7 @@
 // #define RAMPS_V_1_0
 
 
-#if MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 77
+#if MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 77
 
   #define LARGE_FLASH true
   
@@ -392,7 +392,7 @@
     #define LED_PIN            13
   #endif
 
-  #if MOTHERBOARD == 33
+  #if MOTHERBOARD == 33 || MOTHERBOARD == 35
     #define FAN_PIN            9 // (Sprinter config)
   #else
     #define FAN_PIN            4 // IO pin. Buffer needed
@@ -401,6 +401,10 @@
   #if MOTHERBOARD == 77
     #define FAN_PIN            8 
   #endif
+  
+  #if MOTHERBOARD == 35
+    #define CONTROLLERFAN_PIN  10 //Pin used for the fan to cool controller
+  #endif
 
   #define PS_ON_PIN          12
 
@@ -410,12 +414,18 @@
     #define KILL_PIN           -1
   #endif
 
-  #define HEATER_0_PIN       10   // EXTRUDER 1
+  #if MOTHERBOARD == 35
+    #define HEATER_0_PIN       8
+  #else
+    #define HEATER_0_PIN       10   // EXTRUDER 1
+  #endif
+
   #if MOTHERBOARD == 33 
     #define HEATER_1_PIN       -1
   #else
     #define HEATER_1_PIN       9    // EXTRUDER 2 (FAN On Sprinter)
   #endif
+
   #define HEATER_2_PIN       -1 
 
   #if MOTHERBOARD == 77
@@ -427,10 +437,15 @@
   #define TEMP_0_PIN         13   // ANALOG NUMBERING
   #define TEMP_1_PIN         15   // ANALOG NUMBERING
   #define TEMP_2_PIN         -1   // ANALOG NUMBERING
-  #if MOTHERBOARD == 77
-    #define HEATER_BED_PIN     9    // BED
+
+  #if MOTHERBOARD == 35
+    #define HEATER_BED_PIN     -1    // NO BED
   #else
-    #define HEATER_BED_PIN     8    // BED
+    #if MOTHERBOARD == 77
+      #define HEATER_BED_PIN     9    // BED
+    #else
+      #define HEATER_BED_PIN     8    // BED
+    #endif
   #endif
   #define TEMP_BED_PIN       14   // ANALOG NUMBERING
 
@@ -578,7 +593,7 @@
 #define TEMP_2_PIN          -1   
 #define TEMP_BED_PIN        1    // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
 
-#endif // MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 77
+#endif // MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 77
 
 // SPI for Max6675 Thermocouple 
 
@@ -592,9 +607,7 @@
   #define MAX6675_SS       49
 #endif
 
-#endif //MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 77
-
-
+#endif //MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 77
 
 /****************************************************************************************
 * Duemilanove w/ ATMega328P pin assignment

Marlin/ultralcd.cpp

@@ -40,6 +40,7 @@ void copy_and_scalePID_d();
 /* Different menus */
 static void lcd_status_screen();
 #ifdef ULTIPANEL
+extern bool powersupply;
 static void lcd_main_menu();
 static void lcd_tune_menu();
 static void lcd_prepare_menu();
@@ -348,6 +349,14 @@ static void lcd_prepare_menu()
     MENU_ITEM(function, MSG_PREHEAT_PLA, lcd_preheat_pla);
     MENU_ITEM(function, MSG_PREHEAT_ABS, lcd_preheat_abs);
     MENU_ITEM(function, MSG_COOLDOWN, lcd_cooldown);
+#if PS_ON_PIN > -1
+    if (powersupply)
+    {
+        MENU_ITEM(gcode, MSG_SWITCH_PS_OFF, PSTR("M81"));
+    }else{
+        MENU_ITEM(gcode, MSG_SWITCH_PS_ON, PSTR("M80"));
+    }
+#endif
     MENU_ITEM(submenu, MSG_MOVE_AXIS, lcd_move_menu);
     END_MENU();
 }