✨ EasyThreeD ET4000+ board and UI (#23080)
Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>x301
schmttc
3 years ago
committed by
Scott Lahteine
parent
0e60c8b7e0
commit
d75e7784e5
@ -0,0 +1,236 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
#include "../inc/MarlinConfigPre.h"
|
||||
|
||||
#if ENABLED(EASYTHREED_UI)
|
||||
|
||||
#include "easythreed_ui.h"
|
||||
#include "pause.h"
|
||||
#include "../module/temperature.h"
|
||||
#include "../module/printcounter.h"
|
||||
#include "../sd/cardreader.h"
|
||||
#include "../gcode/queue.h"
|
||||
#include "../module/motion.h"
|
||||
#include "../module/planner.h"
|
||||
#include "../MarlinCore.h"
|
||||
|
||||
EasythreedUI easythreed_ui;
|
||||
|
||||
#define BTN_DEBOUNCE_MS 20
|
||||
|
||||
void EasythreedUI::init() {
|
||||
SET_INPUT_PULLUP(BTN_HOME); SET_OUTPUT(BTN_HOME_GND);
|
||||
SET_INPUT_PULLUP(BTN_FEED); SET_OUTPUT(BTN_FEED_GND);
|
||||
SET_INPUT_PULLUP(BTN_RETRACT); SET_OUTPUT(BTN_RETRACT_GND);
|
||||
SET_INPUT_PULLUP(BTN_PRINT);
|
||||
SET_OUTPUT(EASYTHREED_LED_PIN);
|
||||
}
|
||||
|
||||
void EasythreedUI::run() {
|
||||
blinkLED();
|
||||
loadButton();
|
||||
printButton();
|
||||
}
|
||||
|
||||
enum LEDInterval : uint16_t {
|
||||
LED_OFF = 0,
|
||||
LED_ON = 4000,
|
||||
LED_BLINK_0 = 2500,
|
||||
LED_BLINK_1 = 1500,
|
||||
LED_BLINK_2 = 1000,
|
||||
LED_BLINK_3 = 800,
|
||||
LED_BLINK_4 = 500,
|
||||
LED_BLINK_5 = 300,
|
||||
LED_BLINK_6 = 150,
|
||||
LED_BLINK_7 = 50
|
||||
};
|
||||
|
||||
uint16_t blink_interval_ms = LED_ON; // Status LED on Start button
|
||||
|
||||
void EasythreedUI::blinkLED() {
|
||||
static millis_t prev_blink_interval_ms = 0, blink_start_ms = 0;
|
||||
|
||||
if (blink_interval_ms == LED_OFF) { WRITE(EASYTHREED_LED_PIN, HIGH); return; } // OFF
|
||||
if (blink_interval_ms >= LED_ON) { WRITE(EASYTHREED_LED_PIN, LOW); return; } // ON
|
||||
|
||||
const millis_t ms = millis();
|
||||
if (prev_blink_interval_ms != blink_interval_ms) {
|
||||
prev_blink_interval_ms = blink_interval_ms;
|
||||
blink_start_ms = ms;
|
||||
}
|
||||
if (PENDING(ms, blink_start_ms + blink_interval_ms))
|
||||
WRITE(EASYTHREED_LED_PIN, LOW);
|
||||
else if (PENDING(ms, blink_start_ms + 2 * blink_interval_ms))
|
||||
WRITE(EASYTHREED_LED_PIN, HIGH);
|
||||
else
|
||||
blink_start_ms = ms;
|
||||
}
|
||||
|
||||
//
|
||||
// Filament Load/Unload Button
|
||||
// Load/Unload buttons are a 3 position switch with a common center ground.
|
||||
//
|
||||
void EasythreedUI::loadButton() {
|
||||
if (printingIsActive()) return;
|
||||
|
||||
enum FilamentStatus : uint8_t { FS_IDLE, FS_PRESS, FS_CHECK, FS_PROCEED };
|
||||
static uint8_t filament_status = FS_IDLE;
|
||||
static millis_t filament_time = 0;
|
||||
|
||||
switch (filament_status) {
|
||||
|
||||
case FS_IDLE:
|
||||
if (!READ(BTN_RETRACT) || !READ(BTN_FEED)) { // If feed/retract switch is toggled...
|
||||
filament_status++; // ...proceed to next test.
|
||||
filament_time = millis();
|
||||
}
|
||||
break;
|
||||
|
||||
case FS_PRESS:
|
||||
if (ELAPSED(millis(), filament_time + BTN_DEBOUNCE_MS)) { // After a short debounce delay...
|
||||
if (!READ(BTN_RETRACT) || !READ(BTN_FEED)) { // ...if switch still toggled...
|
||||
thermalManager.setTargetHotend(EXTRUDE_MINTEMP + 10, 0); // Start heating up
|
||||
blink_interval_ms = LED_BLINK_7; // Set the LED to blink fast
|
||||
filament_status++;
|
||||
}
|
||||
else
|
||||
filament_status = FS_IDLE; // Switch not toggled long enough
|
||||
}
|
||||
break;
|
||||
|
||||
case FS_CHECK:
|
||||
if (READ(BTN_RETRACT) && READ(BTN_FEED)) { // Switch in center position (stop)
|
||||
blink_interval_ms = LED_ON; // LED on steady
|
||||
filament_status = FS_IDLE;
|
||||
thermalManager.disable_all_heaters();
|
||||
}
|
||||
else if (thermalManager.hotEnoughToExtrude(0)) { // Is the hotend hot enough to move material?
|
||||
filament_status++; // Proceed to feed / retract.
|
||||
blink_interval_ms = LED_BLINK_5; // Blink ~3 times per second
|
||||
}
|
||||
break;
|
||||
|
||||
case FS_PROCEED: {
|
||||
// Feed or Retract just once. Hard abort all moves and return to idle on swicth release.
|
||||
static bool flag = false;
|
||||
if (READ(BTN_RETRACT) && READ(BTN_FEED)) { // Switch in center position (stop)
|
||||
flag = false; // Restore flag to false
|
||||
filament_status = FS_IDLE; // Go back to idle state
|
||||
quickstop_stepper(); // Hard-stop all the steppers ... now!
|
||||
thermalManager.disable_all_heaters(); // And disable all the heaters
|
||||
blink_interval_ms = LED_ON;
|
||||
}
|
||||
else if (!flag) {
|
||||
flag = true;
|
||||
queue.inject(!READ(BTN_RETRACT) ? F("G91\nG0 E10 F180\nG0 E-120 F180\nM104 S0") : F("G91\nG0 E100 F120\nM104 S0"));
|
||||
}
|
||||
} break;
|
||||
}
|
||||
|
||||
}
|
||||
|
||||
#if HAS_STEPPER_RESET
|
||||
void disableStepperDrivers();
|
||||
#endif
|
||||
|
||||
//
|
||||
// Print Start/Pause/Resume Button
|
||||
//
|
||||
void EasythreedUI::printButton() {
|
||||
enum KeyStatus : uint8_t { KS_IDLE, KS_PRESS, KS_PROCEED };
|
||||
static uint8_t key_status = KS_IDLE;
|
||||
static millis_t key_time = 0;
|
||||
|
||||
enum PrintFlag : uint8_t { PF_START, PF_PAUSE, PF_RESUME };
|
||||
static PrintFlag print_key_flag = PF_START;
|
||||
|
||||
const millis_t ms = millis();
|
||||
|
||||
switch (key_status) {
|
||||
case KS_IDLE:
|
||||
if (!READ(BTN_PRINT)) { // Print/Pause/Resume button pressed?
|
||||
key_time = ms; // Save start time
|
||||
key_status++; // Go to debounce test
|
||||
}
|
||||
break;
|
||||
|
||||
case KS_PRESS:
|
||||
if (ELAPSED(ms, key_time + BTN_DEBOUNCE_MS)) // Wait for debounce interval to expire
|
||||
key_status = READ(BTN_PRINT) ? KS_IDLE : KS_PROCEED; // Proceed if still pressed
|
||||
break;
|
||||
|
||||
case KS_PROCEED:
|
||||
if (!READ(BTN_PRINT)) break; // Wait for the button to be released
|
||||
key_status = KS_IDLE; // Ready for the next press
|
||||
if (PENDING(ms, key_time + 1200 - BTN_DEBOUNCE_MS)) { // Register a press < 1.2 seconds
|
||||
switch (print_key_flag) {
|
||||
case PF_START: { // The "Print" button starts an SD card print
|
||||
if (printingIsActive()) break; // Already printing? (find another line that checks for 'is planner doing anything else right now?')
|
||||
blink_interval_ms = LED_BLINK_2; // Blink the indicator LED at 1 second intervals
|
||||
print_key_flag = PF_PAUSE; // The "Print" button now pauses the print
|
||||
card.mount(); // Force SD card to mount - now!
|
||||
if (!card.isMounted) { // Failed to mount?
|
||||
blink_interval_ms = LED_OFF; // Turn off LED
|
||||
print_key_flag = PF_START;
|
||||
return; // Bail out
|
||||
}
|
||||
card.ls(); // List all files to serial output
|
||||
const uint16_t filecnt = card.countFilesInWorkDir(); // Count printable files in cwd
|
||||
if (filecnt == 0) return; // None are printable?
|
||||
card.selectFileByIndex(filecnt); // Select the last file according to current sort options
|
||||
card.openAndPrintFile(card.filename); // Start printing it
|
||||
break;
|
||||
}
|
||||
case PF_PAUSE: { // Pause printing (not currently firing)
|
||||
if (!printingIsActive()) break;
|
||||
blink_interval_ms = LED_ON; // Set indicator to steady ON
|
||||
queue.inject(F("M25")); // Queue Pause
|
||||
print_key_flag = PF_RESUME; // The "Print" button now resumes the print
|
||||
break;
|
||||
}
|
||||
case PF_RESUME: { // Resume printing
|
||||
if (printingIsActive()) break;
|
||||
blink_interval_ms = LED_BLINK_2; // Blink the indicator LED at 1 second intervals
|
||||
queue.inject(F("M24")); // Queue resume
|
||||
print_key_flag = PF_PAUSE; // The "Print" button now pauses the print
|
||||
break;
|
||||
}
|
||||
}
|
||||
}
|
||||
else { // Register a longer press
|
||||
if (print_key_flag == PF_START && !printingIsActive()) { // While not printing, this moves Z up 10mm
|
||||
blink_interval_ms = LED_ON;
|
||||
queue.inject(F("G91\nG0 Z10 F600\nG90")); // Raise Z soon after returning to main loop
|
||||
}
|
||||
else { // While printing, cancel print
|
||||
card.abortFilePrintSoon(); // There is a delay while the current steps play out
|
||||
blink_interval_ms = LED_OFF; // Turn off LED
|
||||
}
|
||||
planner.synchronize(); // Wait for commands already in the planner to finish
|
||||
TERN_(HAS_STEPPER_RESET, disableStepperDrivers()); // Disable all steppers - now!
|
||||
print_key_flag = PF_START; // The "Print" button now starts a new print
|
||||
}
|
||||
break;
|
||||
}
|
||||
}
|
||||
#endif // EASYTHREED_UI
|
||||
@ -0,0 +1,35 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
#pragma once
|
||||
|
||||
class EasythreedUI {
|
||||
public:
|
||||
static void init();
|
||||
static void run();
|
||||
|
||||
private:
|
||||
static void blinkLED();
|
||||
static void loadButton();
|
||||
static void printButton();
|
||||
};
|
||||
|
||||
extern EasythreedUI easythreed_ui;
|
||||
Loading…
Reference in New Issue