Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1

Marlin/Configuration_adv.h

@@ -239,6 +239,11 @@
 #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60}  // set the speeds for manual moves (mm/min)
 #endif
 
+//Comment to disable setting feedrate multiplier via encoder
+#ifdef ULTIPANEL
+    #define ULTIPANEL_FEEDMULTIPLY
+#endif
+
 // minimum time in microseconds that a movement needs to take if the buffer is emptied.
 #define DEFAULT_MINSEGMENTTIME        20000
 
@@ -279,6 +284,9 @@
 //=============================Additional Features===========================
 //===========================================================================
 
+//#define CHDK 4        //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
+#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
+
 #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
 #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
 

Marlin/Marlin.h

@@ -203,7 +203,8 @@ void setPwmFrequency(uint8_t pin, int val);
 extern float homing_feedrate[];
 extern bool axis_relative_modes[];
 extern int feedmultiply;
-extern int extrudemultiply; // Sets extrude multiply factor (in percent)
+extern int extrudemultiply; // Sets extrude multiply factor (in percent) for all extruders
+extern int extruder_multiply[EXTRUDERS]; // sets extrude multiply factor (in percent) for each extruder individually
 extern float volumetric_multiplier[EXTRUDERS]; // reciprocal of cross-sectional area of filament (in square millimeters), stored this way to reduce computational burden in planner
 extern float current_position[NUM_AXIS] ;
 extern float add_homeing[3];

Marlin/Marlin_main.cpp

@@ -189,6 +189,14 @@ bool axis_relative_modes[] = AXIS_RELATIVE_MODES;
 int feedmultiply=100; //100->1 200->2
 int saved_feedmultiply;
 int extrudemultiply=100; //100->1 200->2
+int extruder_multiply[EXTRUDERS] = {100
+  #if EXTRUDERS > 1
+    , 100
+    #if EXTRUDERS > 2
+      , 100
+    #endif
+  #endif
+};
 float volumetric_multiplier[EXTRUDERS] = {1.0
   #if EXTRUDERS > 1
     , 1.0
@@ -314,6 +322,12 @@ bool Stopped=false;
 bool CooldownNoWait = true;
 bool target_direction;
 
+//Insert variables if CHDK is defined
+#ifdef CHDK
+unsigned long chdkHigh = 0;
+boolean chdkActive = false;
+#endif
+
 //===========================================================================
 //=============================Routines======================================
 //===========================================================================
@@ -2422,7 +2436,18 @@ void process_commands()
     {
       if(code_seen('S'))
       {
-        extrudemultiply = code_value() ;
+        int tmp_code = code_value();
+        if (code_seen('T'))
+        {
+          if(setTargetedHotend(221)){
+            break;
+          }
+          extruder_multiply[tmp_extruder] = tmp_code;
+        }
+        else
+        {
+          extrudemultiply = tmp_code ;
+        }
       }
     }
     break;
@@ -2590,23 +2615,33 @@ void process_commands()
     #endif //PIDTEMP
     case 240: // M240  Triggers a camera by emulating a Canon RC-1 : http://www.doc-diy.net/photo/rc-1_hacked/
      {
-      #if defined(PHOTOGRAPH_PIN) && PHOTOGRAPH_PIN > -1
-        const uint8_t NUM_PULSES=16;
-        const float PULSE_LENGTH=0.01524;
-        for(int i=0; i < NUM_PULSES; i++) {
-          WRITE(PHOTOGRAPH_PIN, HIGH);
-          _delay_ms(PULSE_LENGTH);
-          WRITE(PHOTOGRAPH_PIN, LOW);
-          _delay_ms(PULSE_LENGTH);
+     	#ifdef CHDK
+       
+         SET_OUTPUT(CHDK);
+         WRITE(CHDK, HIGH);
+         chdkHigh = millis();
+         chdkActive = true;
+       
+       #else
+     	
+      	#if defined(PHOTOGRAPH_PIN) && PHOTOGRAPH_PIN > -1
+	const uint8_t NUM_PULSES=16;
+	const float PULSE_LENGTH=0.01524;
+	for(int i=0; i < NUM_PULSES; i++) {
+        WRITE(PHOTOGRAPH_PIN, HIGH);
+        _delay_ms(PULSE_LENGTH);
+        WRITE(PHOTOGRAPH_PIN, LOW);
+        _delay_ms(PULSE_LENGTH);
         }
         delay(7.33);
         for(int i=0; i < NUM_PULSES; i++) {
-          WRITE(PHOTOGRAPH_PIN, HIGH);
-          _delay_ms(PULSE_LENGTH);
-          WRITE(PHOTOGRAPH_PIN, LOW);
-          _delay_ms(PULSE_LENGTH);
+        WRITE(PHOTOGRAPH_PIN, HIGH);
+        _delay_ms(PULSE_LENGTH);
+        WRITE(PHOTOGRAPH_PIN, LOW);
+        _delay_ms(PULSE_LENGTH);
         }
-      #endif
+      	#endif
+      #endif //chdk end if
      }
     break;
 #ifdef DOGLCD
@@ -3355,6 +3390,16 @@ void manage_inactivity()
       }
     }
   }
+  
+  #ifdef CHDK //Check if pin should be set to LOW after M240 set it to HIGH
+    if (chdkActive)
+    {
+      chdkActive = false;
+      if (millis()-chdkHigh < CHDK_DELAY) return;
+      WRITE(CHDK, LOW);
+    }
+  #endif
+  
   #if defined(KILL_PIN) && KILL_PIN > -1
     if( 0 == READ(KILL_PIN) )
       kill();
@@ -3522,6 +3567,9 @@ bool setTargetedHotend(int code){
         case 218:
           SERIAL_ECHO(MSG_M218_INVALID_EXTRUDER);
           break;
+        case 221:
+          SERIAL_ECHO(MSG_M221_INVALID_EXTRUDER);
+          break;
       }
       SERIAL_ECHOLN(tmp_extruder);
       return true;

Marlin/language.h

@@ -77,8 +77,18 @@
 	#define MSG_AUTO_HOME "Auto home"
 	#define MSG_SET_ORIGIN "Set origin"
 	#define MSG_PREHEAT_PLA "Preheat PLA"
+	#define MSG_PREHEAT_PLA0 "Preheat PLA 1"
+	#define MSG_PREHEAT_PLA1 "Preheat PLA 2"
+	#define MSG_PREHEAT_PLA2 "Preheat PLA 3"
+	#define MSG_PREHEAT_PLA012 "Preheat PLA All"
+	#define MSG_PREHEAT_PLA_BEDONLY "Preheat PLA Bed"
 	#define MSG_PREHEAT_PLA_SETTINGS "Preheat PLA conf"
 	#define MSG_PREHEAT_ABS "Preheat ABS"
+	#define MSG_PREHEAT_ABS0 "Preheat ABS 1"
+	#define MSG_PREHEAT_ABS1 "Preheat ABS 2"
+	#define MSG_PREHEAT_ABS2 "Preheat ABS 3"
+	#define MSG_PREHEAT_ABS012 "Preheat ABS All"
+	#define MSG_PREHEAT_ABS_BEDONLY "Preheat ABS Bed"
 	#define MSG_PREHEAT_ABS_SETTINGS "Preheat ABS conf"
 	#define MSG_COOLDOWN "Cooldown"
 	#define MSG_SWITCH_PS_ON "Switch power on"
@@ -100,6 +110,9 @@
 	#define MSG_BED "Bed"
 	#define MSG_FAN_SPEED "Fan speed"
 	#define MSG_FLOW "Flow"
+	#define MSG_FLOW0 "Flow 0"
+	#define MSG_FLOW1 "Flow 1"
+	#define MSG_FLOW2 "Flow 2"
 	#define MSG_CONTROL "Control"
 	#define MSG_MIN " \002 Min"
 	#define MSG_MAX " \002 Max"
@@ -192,6 +205,7 @@
 	#define MSG_M105_INVALID_EXTRUDER "M105 Invalid extruder "
 	#define MSG_M200_INVALID_EXTRUDER "M200 Invalid extruder "
 	#define MSG_M218_INVALID_EXTRUDER "M218 Invalid extruder "
+	#define MSG_M221_INVALID_EXTRUDER "M221 Invalid extruder "
 	#define MSG_ERR_NO_THERMISTORS "No thermistors - no temperature"
 	#define MSG_M109_INVALID_EXTRUDER "M109 Invalid extruder "
 	#define MSG_HEATING "Heating..."
@@ -247,7 +261,6 @@
 
 #if LANGUAGE_CHOICE == 2
 
-
 // LCD Menu Messages
 // Please note these are limited to 17 characters!
 
@@ -260,8 +273,18 @@
 	#define MSG_AUTO_HOME "Auto. poz. zerowa"
 	#define MSG_SET_ORIGIN "Ustaw punkt zero"
 	#define MSG_PREHEAT_PLA "Rozgrzej PLA"
+	#define MSG_PREHEAT_PLA0 "Rozgrzej PLA 1"
+	#define MSG_PREHEAT_PLA1 "Rozgrzej PLA 2"
+	#define MSG_PREHEAT_PLA2 "Rozgrzej PLA 3"
+	#define MSG_PREHEAT_PLA012 "Roz. PLA Wszystko"
+	#define MSG_PREHEAT_PLA_BEDONLY "Rozgrzej PLA Loze"
 	#define MSG_PREHEAT_PLA_SETTINGS "Ustaw. rozg. PLA"
 	#define MSG_PREHEAT_ABS "Rozgrzej ABS"
+	#define MSG_PREHEAT_ABS0 "Rozgrzej ABS 1"
+	#define MSG_PREHEAT_ABS1 "Rozgrzej ABS 2"
+	#define MSG_PREHEAT_ABS2 "Rozgrzej ABS 3"
+	#define MSG_PREHEAT_ABS012 "Roz. ABS Wszystko"
+	#define MSG_PREHEAT_ABS_BEDONLY "Rozgrzej ABS Loze"
 	#define MSG_PREHEAT_ABS_SETTINGS "Ustaw. rozg. ABS"
 	#define MSG_COOLDOWN "Chlodzenie"
 	#define MSG_SWITCH_PS_ON "Wlacz zasilacz"
@@ -283,6 +306,9 @@
 	#define MSG_BED "Loze"
 	#define MSG_FAN_SPEED "Obroty wiatraka"
 	#define MSG_FLOW "Przeplyw"
+	#define MSG_FLOW0 "Przeplyw 0"
+	#define MSG_FLOW1 "Przeplyw 1"
+	#define MSG_FLOW2 "Przeplyw 2"
 	#define MSG_CONTROL "Kontrola"
 	#define MSG_MIN " \002 Min"
 	#define MSG_MAX " \002 Max"
@@ -378,6 +404,7 @@
 	#define MSG_M105_INVALID_EXTRUDER "M105 Niepoprawny ekstruder "
 	#define MSG_M200_INVALID_EXTRUDER "M200 Niepoprawny ekstruder "
 	#define MSG_M218_INVALID_EXTRUDER "M218 Niepoprawny ekstruder "
+	#define MSG_M221_INVALID_EXTRUDER "M221 Niepoprawny ekstruder "
 	#define MSG_ERR_NO_THERMISTORS "Brak termistorow - brak temperatury :("
 	#define MSG_M109_INVALID_EXTRUDER "M109 Niepoprawny ekstruder "
 	#define MSG_HEATING "Nagrzewanie ekstrudera..."
@@ -445,8 +472,18 @@
 	#define MSG_AUTO_HOME "Home auto."
 	#define MSG_SET_ORIGIN "Regler origine"
 	#define MSG_PREHEAT_PLA " Prechauffage PLA"
-	#define MSG_PREHEAT_PLA_SETTINGS " Regl. prech. PLA"
+	#define MSG_PREHEAT_PLA0 "Prechauff. PLA 1"
+        #define MSG_PREHEAT_PLA1 "Prechauff. PLA 2"
+	#define MSG_PREHEAT_PLA2 "Prechauff. PLA 3"
+	#define MSG_PREHEAT_PLA012 "Prech. PLA Tout"
+	#define MSG_PREHEAT_PLA_BEDONLY "Prech. PLA Plateau"
+	#define MSG_PREHEAT_PLA_SETTINGS "Regl. prech. PLA"
 	#define MSG_PREHEAT_ABS "Prechauffage ABS"
+	#define MSG_PREHEAT_ABS0 "Prechauff. ABS 1"
+	#define MSG_PREHEAT_ABS1 "Prechauff. ABS 2"
+	#define MSG_PREHEAT_ABS2 "Prechauff. ABS 3"
+	#define MSG_PREHEAT_ABS012 "Prech. ABS Tout"
+	#define MSG_PREHEAT_ABS_BEDONLY "Prech. ABS Plateau"
 	#define MSG_PREHEAT_ABS_SETTINGS "Regl. prech. ABS"
 	#define MSG_COOLDOWN "Refroidir"
 	#define MSG_SWITCH_PS_ON "Allumer alim."
@@ -470,6 +507,9 @@
 	#define MSG_BED "Plateau"
 	#define MSG_FAN_SPEED "Vite. ventilateur"
 	#define MSG_FLOW "Flux"
+	#define MSG_FLOW0 "Flux 0"
+	#define MSG_FLOW1 "Flux 1"
+	#define MSG_FLOW2 "Flux 2"
 	#define MSG_CONTROL "Controler"
 	#define MSG_MIN " \002 Min"
 	#define MSG_MAX " \002 Max"
@@ -563,6 +603,7 @@
 	#define MSG_M105_INVALID_EXTRUDER "M105 Extruder invalide"
 	#define MSG_M200_INVALID_EXTRUDER "M200 Extruder invalide"
 	#define MSG_M218_INVALID_EXTRUDER "M218 Extruder invalide"
+	#define MSG_M221_INVALID_EXTRUDER "M221 Extruder invalide"
 	#define MSG_ERR_NO_THERMISTORS "Pas de thermistor, pas de temperature"
 	#define MSG_M109_INVALID_EXTRUDER "M109 Extruder invalide "
 	#define MSG_HEATING "En chauffe..."
@@ -631,8 +672,18 @@
 	#define MSG_AUTO_HOME        "Auto Nullpunkt"
 	#define MSG_SET_ORIGIN       "Setze Nullpunkt"
 	#define MSG_PREHEAT_PLA      "Vorwärmen PLA"
+	#define MSG_PREHEAT_PLA0     "Vorwärmen PLA 1"
+	#define MSG_PREHEAT_PLA1     "Vorwärmen PLA 2"
+	#define MSG_PREHEAT_PLA2     "Vorwärmen PLA 3"
+	#define MSG_PREHEAT_PLA012   "Vorw. PLA Alle"
+	#define MSG_PREHEAT_PLA_BEDONLY "Vorw. PLA Bett"
 	#define MSG_PREHEAT_PLA_SETTINGS "Vorwärm. PLA Ein."
 	#define MSG_PREHEAT_ABS      "Vorwärmen ABS"
+	#define MSG_PREHEAT_ABS0     "Vorwärmen ABS 1"
+	#define MSG_PREHEAT_ABS1     "Vorwärmen ABS 2"
+	#define MSG_PREHEAT_ABS2     "Vorwärmen ABS 3"
+	#define MSG_PREHEAT_ABS012   "Vorw. ABS Alle"
+	#define MSG_PREHEAT_ABS_BEDONLY "Vorw. ABS Bett"
 	#define MSG_PREHEAT_ABS_SETTINGS "Vorwärm. ABS Ein."
 	#define MSG_COOLDOWN         "Abkühlen"
 	#define MSG_SWITCH_PS_ON     "Switch Power On"
@@ -654,6 +705,9 @@
 	#define MSG_BED              "Bett"
 	#define MSG_FAN_SPEED        "Lüftergeschw."
 	#define MSG_FLOW             "Fluss"
+	#define MSG_FLOW0            "Fluss 0"
+	#define MSG_FLOW1            "Fluss 1"
+	#define MSG_FLOW2            "Fluss 2"
 	#define MSG_CONTROL          "Einstellungen"
 	#define MSG_MIN              "\002 Min"
 	#define MSG_MAX              "\002 Max"
@@ -749,6 +803,7 @@
 	#define MSG_M105_INVALID_EXTRUDER "M105 Invalid extruder "
 	#define MSG_M200_INVALID_EXTRUDER "M200 Invalid extruder "
 	#define MSG_M218_INVALID_EXTRUDER "M218 Invalid extruder "
+	#define MSG_M221_INVALID_EXTRUDER "M221 Invalid extruder "
 	#define MSG_ERR_NO_THERMISTORS "No thermistors - no temp"
 	#define MSG_M109_INVALID_EXTRUDER "M109 Invalid extruder "
 	#define MSG_HEATING "Heating..."
@@ -816,8 +871,18 @@
 	#define MSG_AUTO_HOME "Llevar al origen"
 	#define MSG_SET_ORIGIN "Establecer cero"
 	#define MSG_PREHEAT_PLA "Precalentar PLA"
+	#define MSG_PREHEAT_PLA0 "Precalentar PLA 1"
+	#define MSG_PREHEAT_PLA1 "Precalentar PLA 2"
+	#define MSG_PREHEAT_PLA2 "Precalentar PLA 3"
+	#define MSG_PREHEAT_PLA012 "Precal. PLA Todo"
+	#define MSG_PREHEAT_PLA_BEDONLY "Precal. PLA Base"
 	#define MSG_PREHEAT_PLA_SETTINGS "Ajustar temp. PLA"
 	#define MSG_PREHEAT_ABS "Precalentar ABS"
+	#define MSG_PREHEAT_ABS0 "Precalentar ABS 1"
+	#define MSG_PREHEAT_ABS1 "Precalentar ABS 2"
+	#define MSG_PREHEAT_ABS2 "Precalentar ABS 3"
+	#define MSG_PREHEAT_ABS012 "Precal. ABS Todo"
+	#define MSG_PREHEAT_ABS_BEDONLY "Precal. ABS Base"
 	#define MSG_PREHEAT_ABS_SETTINGS "Ajustar temp. ABS"
 	#define MSG_COOLDOWN "Enfriar"
 	#define MSG_SWITCH_PS_ON "Switch Power On"
@@ -839,6 +904,9 @@
 	#define MSG_BED "Base"
 	#define MSG_FAN_SPEED "Ventilador"
 	#define MSG_FLOW "Flujo"
+	#define MSG_FLOW0 "Flujo 0"
+	#define MSG_FLOW1 "Flujo 1"
+	#define MSG_FLOW2 "Flujo 2"
 	#define MSG_CONTROL "Control"
 	#define MSG_MIN "\002 Min"
 	#define MSG_MAX "\002 Max"
@@ -940,6 +1008,7 @@
 	#define MSG_M105_INVALID_EXTRUDER "M105 Extrusor Invalido "
 	#define MSG_M200_INVALID_EXTRUDER "M200 Extrusor Invalido "
 	#define MSG_M218_INVALID_EXTRUDER "M218 Extrusor Invalido "
+	#define MSG_M221_INVALID_EXTRUDER "M221 Extrusor Invalido "
 	#define MSG_ERR_NO_THERMISTORS "No hay termistores - no temp"
 	#define MSG_M109_INVALID_EXTRUDER "M109 Extrusor Invalido "
 	#define MSG_HEATING "Calentando..."
@@ -997,17 +1066,27 @@
 // LCD Menu Messages
 // Please note these are limited to 17 characters!
 
-	#define WELCOME_MSG MACHINE_NAME			" Готов."
+	#define WELCOME_MSG MACHINE_NAME			        "Готов."
 	#define MSG_SD_INSERTED						"Карта вставлена"
 	#define MSG_SD_REMOVED						"Карта извлечена"
-	#define MSG_MAIN							"Меню            \003"
+	#define MSG_MAIN							"Меню \003"
 	#define MSG_AUTOSTART						"Автостарт"
 	#define MSG_DISABLE_STEPPERS 				"Выкл. двигатели"
 	#define MSG_AUTO_HOME						"Парковка"
 	#define MSG_SET_ORIGIN						"Запомнить ноль"
 	#define MSG_PREHEAT_PLA 					"Преднагрев PLA"
+	#define MSG_PREHEAT_PLA0					"Преднагрев PLA0"
+	#define MSG_PREHEAT_PLA1					"Преднагрев PLA1"
+	#define MSG_PREHEAT_PLA2					"Преднагрев PLA2"
+	#define MSG_PREHEAT_PLA012 					"Преднаг. PLA все"
+	#define MSG_PREHEAT_PLA_BEDONLY 			"Пред. PLA Кровать"
 	#define MSG_PREHEAT_PLA_SETTINGS  			"Настройки PLA"
 	#define MSG_PREHEAT_ABS						"Преднагрев ABS"
+	#define MSG_PREHEAT_ABS0					"Преднагрев ABS0"
+	#define MSG_PREHEAT_ABS1					"Преднагрев ABS1"
+	#define MSG_PREHEAT_ABS2					"Преднагрев ABS2"
+	#define MSG_PREHEAT_ABS012 					"Преднаг. ABS все "
+	#define MSG_PREHEAT_ABS_BEDONLY 			"Пред. ABS Кровать"
 	#define MSG_PREHEAT_ABS_SETTINGS  			"Настройки ABS"
 	#define MSG_COOLDOWN						"Охлаждение"
 	#define MSG_SWITCH_PS_ON					"Switch Power On"
@@ -1029,6 +1108,9 @@
 	#define MSG_BED								"\002 Кровать:"
 	#define MSG_FAN_SPEED						"Куллер:"
 	#define MSG_FLOW							"Поток:"
+	#define MSG_FLOW0 " Поток0:"
+	#define MSG_FLOW1 " Поток1:"
+	#define MSG_FLOW2 " Поток2:"
 	#define MSG_CONTROL							"Настройки \003"
 	#define MSG_MIN								"\002 Минимум:"
 	#define MSG_MAX								"\002 Максимум:"
@@ -1068,8 +1150,8 @@
 	#define MSG_WATCH							"Обзор           \003"
 	#define MSG_PREPARE							"Действия        \x7E"
 	#define MSG_TUNE							"Настройки       \x7E"
-	#define MSG_RESUME_PRINT  					"Продолжить печать"
-	#define MSG_RESUME_PRINT					"Продолжить печать"
+	#define MSG_PAUSE_PRINT  					"Продолжить печать"
+	#define MSG_RESUME_PRINT					"возобн. печать"
 	#define MSG_STOP_PRINT 						"Остановить печать"
 	#define MSG_CARD_MENU						"Меню карты      \x7E"
 	#define MSG_NO_CARD							"Нет карты"
@@ -1122,6 +1204,7 @@
 	#define MSG_M105_INVALID_EXTRUDER			"M105 ошибка экструдера "
 	#define MSG_M200_INVALID_EXTRUDER			"M200 ошибка экструдера "
 	#define MSG_M218_INVALID_EXTRUDER			"M218 ошибка экструдера "
+	#define MSG_M221_INVALID_EXTRUDER			"M221 ошибка экструдера "
 	#define MSG_ERR_NO_THERMISTORS				"Нет термистра - нет температуры"
 	#define MSG_M109_INVALID_EXTRUDER			"M109 ошибка экструдера "
 	#define MSG_HEATING							"Нагрев...  "
@@ -1187,8 +1270,18 @@
 	#define MSG_AUTO_HOME            "Auto Home"
 	#define MSG_SET_ORIGIN           "Imposta Origine"
 	#define MSG_PREHEAT_PLA          "Preriscalda PLA"
+	#define MSG_PREHEAT_PLA0         "Preriscalda PLA 1"
+	#define MSG_PREHEAT_PLA1         "Preriscalda PLA 2"
+	#define MSG_PREHEAT_PLA2         "Preriscalda PLA 3"
+	#define MSG_PREHEAT_PLA012       "Preris. PLA Tutto"
+	#define MSG_PREHEAT_PLA_BEDONLY  "Preri. PLA Piatto"
 	#define MSG_PREHEAT_PLA_SETTINGS "Preris. PLA Conf"
 	#define MSG_PREHEAT_ABS          "Preriscalda ABS"
+	#define MSG_PREHEAT_ABS0         "Preriscalda ABS 1"
+	#define MSG_PREHEAT_ABS1         "Preriscalda ABS 2"
+	#define MSG_PREHEAT_ABS2         "Preriscalda ABS 3"
+	#define MSG_PREHEAT_ABS012       "Preris. ABS Tutto"
+	#define MSG_PREHEAT_ABS_BEDONLY  "Preri. ABS Piatto"
 	#define MSG_PREHEAT_ABS_SETTINGS "Preris. ABS Conf"
 	#define MSG_COOLDOWN             "Raffredda"
 	#define MSG_SWITCH_PS_ON         "Switch Power On"
@@ -1210,6 +1303,9 @@
 	#define MSG_BED                  "Piatto"
 	#define MSG_FAN_SPEED            "Ventola"
 	#define MSG_FLOW                 "Flusso"
+	#define MSG_FLOW0                "Flusso 0"
+	#define MSG_FLOW1                "Flusso 1"
+	#define MSG_FLOW2                "Flusso 2"
 	#define MSG_CONTROL              "Controllo"
 	#define MSG_MIN                  " \002 Min:"
 	#define MSG_MAX                  " \002 Max:"
@@ -1303,6 +1399,7 @@
 	#define MSG_M105_INVALID_EXTRUDER "M105 Estrusore non valido "
 	#define MSG_M200_INVALID_EXTRUDER "M200 Estrusore non valido "
 	#define MSG_M218_INVALID_EXTRUDER "M218 Estrusore non valido "
+	#define MSG_M221_INVALID_EXTRUDER "M221 Estrusore non valido "
 	#define MSG_ERR_NO_THERMISTORS   "Nessun Termistore - nessuna temperatura"
 	#define MSG_M109_INVALID_EXTRUDER "M109 Estrusore non valido "
 	#define MSG_HEATING              "Riscaldamento..."
@@ -1370,8 +1467,18 @@
 	#define MSG_AUTO_HOME "Ir para origen"
 	#define MSG_SET_ORIGIN "Estabelecer orig."
 	#define MSG_PREHEAT_PLA "Pre-aquecer PLA"
+	#define MSG_PREHEAT_PLA0 " pre-aquecer PLA 1"
+	#define MSG_PREHEAT_PLA1 " pre-aquecer PLA 2"
+	#define MSG_PREHEAT_PLA2 " pre-aquecer PLA 3"
+	#define MSG_PREHEAT_PLA012 " pre-aq. PLA Tudo"
+	#define MSG_PREHEAT_PLA_BEDONLY  " pre-aq. PLA \002Base"
 	#define MSG_PREHEAT_PLA_SETTINGS "PLA setting"
 	#define MSG_PREHEAT_ABS "Pre-aquecer ABS"
+	#define MSG_PREHEAT_ABS0 " pre-aquecer ABS 1"
+	#define MSG_PREHEAT_ABS1 " pre-aquecer ABS 2"
+	#define MSG_PREHEAT_ABS2 " pre-aquecer ABS 3"
+	#define MSG_PREHEAT_ABS012 " pre-aq. ABS Tudo"
+	#define MSG_PREHEAT_ABS_BEDONLY  " pre-aq. ABS \002Base"
 	#define MSG_PREHEAT_ABS_SETTINGS "ABS setting"
 	#define MSG_COOLDOWN "Esfriar"
 	#define MSG_SWITCH_PS_ON "Switch Power On"
@@ -1395,6 +1502,9 @@
 	#define MSG_BED "\002Base:"
 	#define MSG_FAN_SPEED "Velocidade vento."
 	#define MSG_FLOW "Fluxo:"
+	#define MSG_FLOW0 "Fluxo0:"
+	#define MSG_FLOW1 "Fluxo1:"
+	#define MSG_FLOW2 "Fluxo2:"
 	#define MSG_CONTROL "Controle \003"
 	#define MSG_MIN "\002 Min:"
 	#define MSG_MAX "\002 Max:"
@@ -1492,6 +1602,7 @@
 	#define MSG_M105_INVALID_EXTRUDER "M105 Extrusor inválido "
 	#define MSG_M200_INVALID_EXTRUDER "M200 Extrusor inválido "
 	#define MSG_M218_INVALID_EXTRUDER "M218 Extrusor inválido "
+	#define MSG_M221_INVALID_EXTRUDER "M221 Extrusor inválido "
 	#define MSG_ERR_NO_THERMISTORS "Nao ha termistor - no temp"
 	#define MSG_M109_INVALID_EXTRUDER "M109 Extrusor inválido "
 	#define MSG_HEATING "Aquecendo..."
@@ -1560,8 +1671,18 @@
 	#define MSG_AUTO_HOME "Aja referenssiin"
 	#define MSG_SET_ORIGIN "Aseta origo"
 	#define MSG_PREHEAT_PLA "Esilammita PLA"
+	#define MSG_PREHEAT_PLA0 "Esilammita PLA 1"
+	#define MSG_PREHEAT_PLA1 "Esilammita PLA 2"
+	#define MSG_PREHEAT_PLA2 "Esilammita PLA 3"
+	#define MSG_PREHEAT_PLA012 "Esila. PLA Kaikki"
+	#define MSG_PREHEAT_PLA_BEDONLY  "Esila. PLA Alusta"
 	#define MSG_PREHEAT_PLA_SETTINGS "Esilamm. PLA konf"
 	#define MSG_PREHEAT_ABS "Esilammita ABS"
+	#define MSG_PREHEAT_ABS0 "Esilammita ABS 1"
+	#define MSG_PREHEAT_ABS1 "Esilammita ABS 2"
+	#define MSG_PREHEAT_ABS2 "Esilammita ABS 3"
+	#define MSG_PREHEAT_ABS012 "Esila. ABS Kaikki"
+	#define MSG_PREHEAT_ABS_BEDONLY  "Esila. ABS Alusta"
 	#define MSG_PREHEAT_ABS_SETTINGS "Esilamm. ABS konf"
 	#define MSG_COOLDOWN "Jaahdyta"
 	#define MSG_SWITCH_PS_ON "Virta paalle"
@@ -1583,6 +1704,9 @@
 	#define MSG_BED "Alusta"
 	#define MSG_FAN_SPEED "Tuul. nopeus"
 	#define MSG_FLOW "Virtaus"
+	#define MSG_FLOW0 "Virtaus 0"
+	#define MSG_FLOW1 "Virtaus 1"
+	#define MSG_FLOW2 "Virtaus 2"
 	#define MSG_CONTROL "Kontrolli"
 	#define MSG_MIN " \002 Min"
 	#define MSG_MAX " \002 Max"
@@ -1675,6 +1799,7 @@
 	#define MSG_M105_INVALID_EXTRUDER "M105 Virheellinen suutin "
 	#define MSG_M200_INVALID_EXTRUDER "M200 Virheellinen suutin "
 	#define MSG_M218_INVALID_EXTRUDER "M218 Virheellinen suutin "
+	#define MSG_M221_INVALID_EXTRUDER "M221 Virheellinen suutin "
 	#define MSG_ERR_NO_THERMISTORS "Ei termistoreja - ei lampotiloja"
 	#define MSG_M109_INVALID_EXTRUDER "M109 Virheellinen suutin "
 	#define MSG_HEATING "Lammitan..."
@@ -1743,8 +1868,18 @@
 	#define MSG_AUTO_HOME "Levar a l'orichen"
 	#define MSG_SET_ORIGIN "Establir zero"
 	#define MSG_PREHEAT_PLA "Precalentar PLA"
+	#define MSG_PREHEAT_PLA0 "Precalentar PLA0"
+	#define MSG_PREHEAT_PLA1 "Precalentar PLA1"
+	#define MSG_PREHEAT_PLA2 "Precalentar PLA2"
+	#define MSG_PREHEAT_PLA012 "Precalentar PLA a"
+	#define MSG_PREHEAT_PLA_BEDONLY  "Prec. PLA Base"
 	#define MSG_PREHEAT_PLA_SETTINGS "Achustar tem. PLA"
 	#define MSG_PREHEAT_ABS "Precalentar ABS"
+	#define MSG_PREHEAT_ABS0 "Precalentar ABS0"
+	#define MSG_PREHEAT_ABS1 "Precalentar ABS1"
+	#define MSG_PREHEAT_ABS2 "Precalentar ABS2"
+	#define MSG_PREHEAT_ABS012 "Precalentar ABS a"
+	#define MSG_PREHEAT_ABS_BEDONLY  "Prec. ABS Base"
 	#define MSG_PREHEAT_ABS_SETTINGS "Achustar tem. ABS"
 	#define MSG_COOLDOWN "Enfriar"
 	#define MSG_SWITCH_PS_ON "Enchegar Fuent"
@@ -1766,6 +1901,9 @@
 	#define MSG_BED "Base"
 	#define MSG_FAN_SPEED "Ixoriador"
 	#define MSG_FLOW "Fluxo"
+	#define MSG_FLOW0 "Fluxo 0"
+	#define MSG_FLOW1 "Fluxo 1"
+	#define MSG_FLOW2 "Fluxo 2"
 	#define MSG_CONTROL "Control"
 	#define MSG_MIN "\002 Min"
 	#define MSG_MAX "\002 Max"
@@ -1867,6 +2005,7 @@
 	#define MSG_M105_INVALID_EXTRUDER "M105 Extrusor Invalido "
 	#define MSG_M200_INVALID_EXTRUDER "M200 Extrusor Invalido "
 	#define MSG_M218_INVALID_EXTRUDER "M218 Extrusor Invalido "
+	#define MSG_M221_INVALID_EXTRUDER "M221 Extrusor Invalido "
 	#define MSG_ERR_NO_THERMISTORS "No i hai termistores - no temp"
 	#define MSG_M109_INVALID_EXTRUDER "M109 Extrusor Invalido "
 	#define MSG_HEATING "Calentando..."
@@ -1932,8 +2071,18 @@
 	#define MSG_AUTO_HOME "Auto home"
 	#define MSG_SET_ORIGIN "Nulpunt instellen"
 	#define MSG_PREHEAT_PLA "PLA voorverwarmen"
+	#define MSG_PREHEAT_PLA0 "PLA voorverw. 0"
+	#define MSG_PREHEAT_PLA1 "PLA voorverw. 1"
+	#define MSG_PREHEAT_PLA2 "PLA voorverw. 2"
+	#define MSG_PREHEAT_PLA012 "PLA voorverw. aan"
+	#define MSG_PREHEAT_PLA_BEDONLY  "PLA voorverw. Bed"
 	#define MSG_PREHEAT_PLA_SETTINGS "PLA verw. conf"
 	#define MSG_PREHEAT_ABS "ABS voorverwarmen"
+	#define MSG_PREHEAT_ABS0 "ABS voorverw. 0"
+	#define MSG_PREHEAT_ABS1 "ABS voorverw. 1"
+	#define MSG_PREHEAT_ABS2 "ABS voorverw. 2"
+	#define MSG_PREHEAT_ABS012 "ABS voorverw. aan"
+	#define MSG_PREHEAT_ABS_BEDONLY  "ABS voorverw. Bed"
 	#define MSG_PREHEAT_ABS_SETTINGS "ABS verw. conf"
 	#define MSG_COOLDOWN "Afkoelen"
 	#define MSG_SWITCH_PS_ON "Stroom aan"
@@ -1955,6 +2104,9 @@
 	#define MSG_BED "Bed"
 	#define MSG_FAN_SPEED "Fan snelheid"
 	#define MSG_FLOW "Flow"
+	#define MSG_FLOW0 "Flow 0"
+	#define MSG_FLOW1 "Flow 1"
+	#define MSG_FLOW2 "Flow 2"
 	#define MSG_CONTROL "Control"
 	#define MSG_MIN " \002 Min"
 	#define MSG_MAX " \002 Max"
@@ -2047,6 +2199,7 @@
 	#define MSG_M105_INVALID_EXTRUDER "M105 Ongeldige extruder "
 	#define MSG_M200_INVALID_EXTRUDER "M200 Ongeldige extruder "
 	#define MSG_M218_INVALID_EXTRUDER "M218 Ongeldige extruder "
+	#define MSG_M221_INVALID_EXTRUDER "M221 Ongeldige extruder "
 	#define MSG_ERR_NO_THERMISTORS "Geen thermistors - geen temperatuur"
 	#define MSG_M109_INVALID_EXTRUDER "M109 Ongeldige extruder "
 	#define MSG_HEATING "Opwarmen..."

Marlin/ultralcd.cpp

@@ -196,6 +196,7 @@ static void lcd_status_screen()
         lcd_quick_feedback();
     }
 
+#ifdef ULTIPANEL_FEEDMULTIPLY
     // Dead zone at 100% feedrate
     if ((feedmultiply < 100 && (feedmultiply + int(encoderPosition)) > 100) ||
             (feedmultiply > 100 && (feedmultiply + int(encoderPosition)) < 100))
@@ -219,6 +220,7 @@ static void lcd_status_screen()
         feedmultiply += int(encoderPosition);
         encoderPosition = 0;
     }
+#endif//ULTIPANEL_FEEDMULTIPLY
 
     if (feedmultiply < 10)
         feedmultiply = 10;
@@ -302,37 +304,6 @@ static void lcd_autostart_sd()
 }
 #endif
 
-void lcd_preheat_pla()
-{
-    setTargetHotend0(plaPreheatHotendTemp);
-    setTargetHotend1(plaPreheatHotendTemp);
-    setTargetHotend2(plaPreheatHotendTemp);
-    setTargetBed(plaPreheatHPBTemp);
-    fanSpeed = plaPreheatFanSpeed;
-    lcd_return_to_status();
-    setWatch(); // heater sanity check timer
-}
-
-void lcd_preheat_abs()
-{
-    setTargetHotend0(absPreheatHotendTemp);
-    setTargetHotend1(absPreheatHotendTemp);
-    setTargetHotend2(absPreheatHotendTemp);
-    setTargetBed(absPreheatHPBTemp);
-    fanSpeed = absPreheatFanSpeed;
-    lcd_return_to_status();
-    setWatch(); // heater sanity check timer
-}
-
-static void lcd_cooldown()
-{
-    setTargetHotend0(0);
-    setTargetHotend1(0);
-    setTargetHotend2(0);
-    setTargetBed(0);
-    lcd_return_to_status();
-}
-
 #ifdef BABYSTEPPING
 static void lcd_babystep_x()
 {
@@ -412,6 +383,13 @@ static void lcd_tune_menu()
 #endif
     MENU_ITEM_EDIT(int3, MSG_FAN_SPEED, &fanSpeed, 0, 255);
     MENU_ITEM_EDIT(int3, MSG_FLOW, &extrudemultiply, 10, 999);
+    MENU_ITEM_EDIT(int3, MSG_FLOW0, &extruder_multiply[0], 10, 999);
+#if TEMP_SENSOR_1 != 0
+    MENU_ITEM_EDIT(int3, MSG_FLOW1, &extruder_multiply[1], 10, 999);
+#endif
+#if TEMP_SENSOR_2 != 0
+    MENU_ITEM_EDIT(int3, MSG_FLOW2, &extruder_multiply[2], 10, 999);
+#endif
 
 #ifdef BABYSTEPPING
     #ifdef BABYSTEP_XY
@@ -426,6 +404,154 @@ static void lcd_tune_menu()
     END_MENU();
 }
 
+void lcd_preheat_pla0()
+{
+    setTargetHotend0(plaPreheatHotendTemp);
+    setTargetBed(plaPreheatHPBTemp);
+    fanSpeed = plaPreheatFanSpeed;
+    lcd_return_to_status();
+    setWatch(); // heater sanity check timer
+}
+
+void lcd_preheat_abs0()
+{
+    setTargetHotend0(absPreheatHotendTemp);
+    setTargetBed(absPreheatHPBTemp);
+    fanSpeed = absPreheatFanSpeed;
+    lcd_return_to_status();
+    setWatch(); // heater sanity check timer
+}
+
+#if TEMP_SENSOR_1 != 0 //2nd extruder preheat
+void lcd_preheat_pla1()
+{
+    setTargetHotend1(plaPreheatHotendTemp);
+    setTargetBed(plaPreheatHPBTemp);
+    fanSpeed = plaPreheatFanSpeed;
+    lcd_return_to_status();
+    setWatch(); // heater sanity check timer
+}
+
+void lcd_preheat_abs1()
+{
+    setTargetHotend1(absPreheatHotendTemp);
+    setTargetBed(absPreheatHPBTemp);
+    fanSpeed = absPreheatFanSpeed;
+    lcd_return_to_status();
+    setWatch(); // heater sanity check timer
+}
+#endif //2nd extruder preheat
+
+#if TEMP_SENSOR_2 != 0 //3 extruder preheat
+void lcd_preheat_pla2()
+{
+    setTargetHotend2(plaPreheatHotendTemp);
+    setTargetBed(plaPreheatHPBTemp);
+    fanSpeed = plaPreheatFanSpeed;
+    lcd_return_to_status();
+    setWatch(); // heater sanity check timer
+}
+
+void lcd_preheat_abs2()
+{
+    setTargetHotend2(absPreheatHotendTemp);
+    setTargetBed(absPreheatHPBTemp);
+    fanSpeed = absPreheatFanSpeed;
+    lcd_return_to_status();
+    setWatch(); // heater sanity check timer
+}
+#endif //3 extruder preheat
+
+#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 //more than one extruder present
+void lcd_preheat_pla012()
+{
+    setTargetHotend0(plaPreheatHotendTemp);
+    setTargetHotend1(plaPreheatHotendTemp);
+    setTargetHotend2(plaPreheatHotendTemp);
+    setTargetBed(plaPreheatHPBTemp);
+    fanSpeed = plaPreheatFanSpeed;
+    lcd_return_to_status();
+    setWatch(); // heater sanity check timer
+}
+
+void lcd_preheat_abs012()
+{
+    setTargetHotend0(absPreheatHotendTemp);
+    setTargetHotend1(absPreheatHotendTemp);
+    setTargetHotend2(absPreheatHotendTemp);
+    setTargetBed(absPreheatHPBTemp);
+    fanSpeed = absPreheatFanSpeed;
+    lcd_return_to_status();
+    setWatch(); // heater sanity check timer
+}
+#endif //more than one extruder present
+
+void lcd_preheat_pla_bedonly()
+{
+    setTargetBed(plaPreheatHPBTemp);
+    fanSpeed = plaPreheatFanSpeed;
+    lcd_return_to_status();
+    setWatch(); // heater sanity check timer
+}
+
+void lcd_preheat_abs_bedonly()
+{
+    setTargetBed(absPreheatHPBTemp);
+    fanSpeed = absPreheatFanSpeed;
+    lcd_return_to_status();
+    setWatch(); // heater sanity check timer
+}
+
+static void lcd_preheat_pla_menu()
+{
+    START_MENU();
+    MENU_ITEM(back, MSG_PREPARE, lcd_prepare_menu);
+    MENU_ITEM(function, MSG_PREHEAT_PLA0, lcd_preheat_pla0);
+#if TEMP_SENSOR_1 != 0 //2 extruder preheat
+    MENU_ITEM(function, MSG_PREHEAT_PLA1, lcd_preheat_pla1);
+#endif //2 extruder preheat
+#if TEMP_SENSOR_2 != 0 //3 extruder preheat
+    MENU_ITEM(function, MSG_PREHEAT_PLA2, lcd_preheat_pla2);
+#endif //3 extruder preheat
+#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 //all extruder preheat
+    MENU_ITEM(function, MSG_PREHEAT_PLA012, lcd_preheat_pla012);
+#endif //2 extruder preheat
+#if TEMP_SENSOR_BED != 0
+    MENU_ITEM(function, MSG_PREHEAT_PLA_BEDONLY, lcd_preheat_pla_bedonly);
+#endif
+    END_MENU();
+}
+
+static void lcd_preheat_abs_menu()
+{
+    START_MENU();
+    MENU_ITEM(back, MSG_PREPARE, lcd_prepare_menu);
+    MENU_ITEM(function, MSG_PREHEAT_ABS0, lcd_preheat_abs0);
+#if TEMP_SENSOR_1 != 0 //2 extruder preheat
+    MENU_ITEM(function, MSG_PREHEAT_ABS1, lcd_preheat_abs1);
+#endif //2 extruder preheat
+#if TEMP_SENSOR_2 != 0 //3 extruder preheat
+    MENU_ITEM(function, MSG_PREHEAT_ABS2, lcd_preheat_abs2);
+#endif //3 extruder preheat
+#if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 //all extruder preheat
+    MENU_ITEM(function, MSG_PREHEAT_ABS012, lcd_preheat_abs012);
+#endif //2 extruder preheat
+#if TEMP_SENSOR_BED != 0
+    MENU_ITEM(function, MSG_PREHEAT_ABS_BEDONLY, lcd_preheat_abs_bedonly);
+#endif
+    END_MENU();
+}
+
+void lcd_cooldown()
+{
+    setTargetHotend0(0);
+    setTargetHotend1(0);
+    setTargetHotend2(0);
+    setTargetBed(0);
+    fanSpeed = 0;
+    lcd_return_to_status();
+}
+
 static void lcd_prepare_menu()
 {
     START_MENU();
@@ -438,8 +564,15 @@ static void lcd_prepare_menu()
     MENU_ITEM(gcode, MSG_DISABLE_STEPPERS, PSTR("M84"));
     MENU_ITEM(gcode, MSG_AUTO_HOME, PSTR("G28"));
     //MENU_ITEM(gcode, MSG_SET_ORIGIN, PSTR("G92 X0 Y0 Z0"));
-    MENU_ITEM(function, MSG_PREHEAT_PLA, lcd_preheat_pla);
-    MENU_ITEM(function, MSG_PREHEAT_ABS, lcd_preheat_abs);
+#if TEMP_SENSOR_0 != 0
+  #if TEMP_SENSOR_1 != 0 || TEMP_SENSOR_2 != 0 || TEMP_SENSOR_BED != 0
+    MENU_ITEM(submenu, MSG_PREHEAT_PLA, lcd_preheat_pla_menu);
+    MENU_ITEM(submenu, MSG_PREHEAT_ABS, lcd_preheat_abs_menu);
+  #else
+    MENU_ITEM(function, MSG_PREHEAT_PLA, lcd_preheat_pla0);
+    MENU_ITEM(function, MSG_PREHEAT_ABS, lcd_preheat_abs0);
+  #endif
+#endif
     MENU_ITEM(function, MSG_COOLDOWN, lcd_cooldown);
 #if PS_ON_PIN > -1
     if (powersupply)