diff --git a/Marlin/src/pins/pins_RAMPS_RE_ARM.h b/Marlin/src/pins/pins_RAMPS_RE_ARM.h index 1d583cbafa..29f31fc630 100644 --- a/Marlin/src/pins/pins_RAMPS_RE_ARM.h +++ b/Marlin/src/pins/pins_RAMPS_RE_ARM.h @@ -98,13 +98,6 @@ #define E1_CS_PIN -1 #endif -//#define E2_STEP_PIN P2_08 // (36) -//#define E2_DIR_PIN P2_13 // (34) -//#define E2_ENABLE_PIN P4_29 // (30) -//#ifndef E2_CS_PIN -// #define E2_CS_PIN -1 -//#endif - // // Software SPI pins for TMC2130 stepper drivers // @@ -118,14 +111,14 @@ // Temperature Sensors // 3.3V max when defined as an analog input // -#define TEMP_0_PIN 0 // A0 (T0) - (67) - TEMP_0_PIN -#define TEMP_BED_PIN 1 // A1 (T1) - (68) - TEMP_BED_PIN -#define TEMP_1_PIN 2 // A2 (T2) - (69) - TEMP_1_PIN -#define TEMP_2_PIN 3 // A3 - (63) - J5-3 & AUX-2 -#define TEMP_3_PIN 4 // A4 - (37) - BUZZER_PIN -//#define TEMP_4_PIN 5 // A5 - (49) - SD_DETECT_PIN -//#define ?? 6 // A6 - ( 0) - RXD0 - J4-4 & AUX-1 -#define FILWIDTH_PIN 7 // A7 - ( 1) - TXD0 - J4-5 & AUX-1 +#define TEMP_0_PIN 0 // A0 (T0) - (67) - TEMP_0_PIN +#define TEMP_BED_PIN 1 // A1 (T1) - (68) - TEMP_BED_PIN +#define TEMP_1_PIN 2 // A2 (T2) - (69) - TEMP_1_PIN +#define TEMP_2_PIN 3 // A3 - (63) - J5-3 & AUX-2 +#define TEMP_3_PIN 4 // A4 - (37) - BUZZER_PIN +//#define TEMP_4_PIN 5 // A5 - (49) - SD_DETECT_PIN +//#define ?? 6 // A6 - ( 0) - RXD0 - J4-4 & AUX-1 +#define FILWIDTH_PIN 7 // A7 - ( 1) - TXD0 - J4-5 & AUX-1 // // Augmentation for auto-assigning RAMPS plugs @@ -195,55 +188,57 @@ // // Misc. Functions // -#define LED_PIN P4_28 // (13) +#define LED_PIN P4_28 // (13) // define digital pin 4 for the filament runout sensor. Use the RAMPS 1.4 digital input 4 on the servos connector #ifndef FIL_RUNOUT_PIN - #define FIL_RUNOUT_PIN P1_18 // (4) + #define FIL_RUNOUT_PIN P1_18 // (4) #endif -#define PS_ON_PIN P2_12 // (12) +#define PS_ON_PIN P2_12 // (12) #if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN) - #if !defined(NUM_SERVOS) || NUM_SERVOS < 4 // try to use servo connector - #define CASE_LIGHT_PIN P1_18 // (4) MUST BE HARDWARE PWM + #if !defined(NUM_SERVOS) || NUM_SERVOS < 4 // Try to use servo connector + #define CASE_LIGHT_PIN P1_18 // (4) MUST BE HARDWARE PWM #endif #endif // // M3/M4/M5 - Spindle/Laser Control +// Use servo pins, if available // #if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENABLE) - #if !defined(NUM_SERVOS) || NUM_SERVOS == 1 // must use servo connector - #undef SERVO1 - #undef SERVO2 - #undef SERVO3 - #define SPINDLE_LASER_ENABLE_PIN P1_21 // (6) Pin should have a pullup/pulldown! - #define SPINDLE_LASER_PWM_PIN P1_18 // (4) MUST BE HARDWARE PWM - #define SPINDLE_DIR_PIN P1_19 // (5) + #if NUM_SERVOS > 1 + #error "SPINDLE_LASER_ENABLE requires 3 free servo pins." #endif + #define SPINDLE_LASER_ENABLE_PIN SERVO1_PIN // (6) Pin should have a pullup/pulldown! + #define SPINDLE_LASER_PWM_PIN SERVO3_PIN // (4) MUST BE HARDWARE PWM + #define SPINDLE_DIR_PIN SERVO2_PIN // (5) #endif // // Průša i3 MK2 Multiplexer Support // #if SERIAL_PORT != 0 && SERIAL_PORT_2 != 0 - #define E_MUX0_PIN P0_03 // ( 0) Z_CS_PIN - #define E_MUX1_PIN P0_02 // ( 1) E0_CS_PIN + #define E_MUX0_PIN P0_03 // ( 0) Z_CS_PIN + #define E_MUX1_PIN P0_02 // ( 1) E0_CS_PIN #endif #define E_MUX2_PIN P0_26 // (63) E1_CS_PIN /** * LCD / Controller * - * All controllers can use J3 and J5 on the Re-ARM board. Custom cabling will be required. + * All controllers can use J3 and J5 on the Re-ARM board. Custom cabling will be required. + * + * - https://github.com/wolfmanjm/universal-panel-adapter + * - http://panucattdevices.freshdesk.com/support/solutions/articles/1000243195-lcd-display-installation */ /** * Smart LCD adapter * * The Smart LCD adapter can be used for the two 10 pin LCD controllers such as - * REPRAP_DISCOUNT_SMART_CONTROLLER. It can't be used for controllers that use + * REPRAP_DISCOUNT_SMART_CONTROLLER. It can't be used for controllers that use * DOGLCD_A0, DOGLCD_CS, LCD_PINS_D5, LCD_PINS_D6 or LCD_PINS_D7. A custom cable * is needed to pick up 5V for the EXP1 connection. * @@ -252,95 +247,91 @@ * that the garbage/lines are erased immediately after the SD card accesses are completed. */ -#if ENABLED(ULTRA_LCD) +#if ENABLED(CR10_STOCKDISPLAY) - #if ENABLED(CR10_STOCKDISPLAY) + // Re-Arm can support Creality stock display without SD card reader and single cable on EXP3. + // Re-Arm J3 pins 1 (p1.31) & 2 (P3.26) are not used. Stock cable will need to have one + // 10-pin IDC connector trimmed or replaced with a 12-pin IDC connector to fit J3. + // Requires REVERSE_ENCODER_DIRECTION in Configuration.h - // Re-Arm can support Creality stock display without SD card reader and single cable on EXP3. - // Re-Arm J3 pins 1 (p1.31) & 2 (P3.26) are not used. Stock cable will need to have one - // 10-pin IDC connector trimmed or replaced with a 12-pin IDC connector to fit J3. - // Requires REVERSE_ENCODER_DIRECTION in Configuration.h + #define BEEPER_PIN P2_11 // J3-3 & AUX-4 - #define BEEPER_PIN P2_11 // J3-3 & AUX-4 + #define BTN_EN1 P0_16 // J3-7 & AUX-4 + #define BTN_EN2 P1_23 // J3-5 & AUX-4 + #define BTN_ENC P3_25 // J3-4 & AUX-4 - #define BTN_EN1 P0_16 // J3-7 & AUX-4 - #define BTN_EN2 P1_23 // J3-5 & AUX-4 - #define BTN_ENC P3_25 // J3-4 & AUX-4 + #define LCD_PINS_RS P0_15 // J3-9 & AUX-4 (CS) + #define LCD_PINS_ENABLE P0_18 // J3-10 & AUX-3 (SID, MOSI) + #define LCD_PINS_D4 P2_06 // J3-8 & AUX-3 (SCK, CLK) - #define LCD_PINS_RS P0_15 // J3-9 & AUX-4 (CS) - #define LCD_PINS_ENABLE P0_18 // J3-10 & AUX-3 (SID, MOSI) - #define LCD_PINS_D4 P2_06 // J3-8 & AUX-3 (SCK, CLK) +#elif ENABLED(ULTRA_LCD) + #define BEEPER_PIN P1_30 // (37) not 5V tolerant + + #define BTN_EN1 P3_26 // (31) J3-2 & AUX-4 + #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4 + #define BTN_ENC P2_11 // (35) J3-3 & AUX-4 + + #define SD_DETECT_PIN P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant) + #define KILL_PIN P1_22 // (41) J5-4 & AUX-4 + #define LCD_PINS_RS P0_16 // (16) J3-7 & AUX-4 + #define LCD_SDSS P0_16 // (16) J3-7 & AUX-4 + + #if ENABLED(NEWPANEL) + #if ENABLED(REPRAPWORLD_KEYPAD) + #define SHIFT_OUT P0_18 // (51) (MOSI) J3-10 & AUX-3 + #define SHIFT_CLK P0_15 // (52) (SCK) J3-9 & AUX-3 + #define SHIFT_LD P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant) + #endif #else + //#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4 + //#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4 + //#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4 + //#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4 + #endif - #define BEEPER_PIN P1_30 // (37) not 5V tolerant + #if ENABLED(VIKI2) || ENABLED(miniVIKI) + // #define LCD_SCREEN_ROT_180 - #define BTN_EN1 P3_26 // (31) J3-2 & AUX-4 - #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4 - #define BTN_ENC P2_11 // (35) J3-3 & AUX-4 + #define BTN_EN1 P3_26 // (31) J3-2 & AUX-4 + #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4 + #define BTN_ENC P2_11 // (35) J3-3 & AUX-4 - #define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3 - #define KILL_PIN P1_22 // (41) J5-4 & AUX-4 - #define LCD_PINS_RS P0_16 // (16) J3-7 & AUX-4 - #define LCD_SDSS P0_16 // (16) J3-7 & AUX-4 + #define SD_DETECT_PIN P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant) + #define KILL_PIN P1_22 // (41) J5-4 & AUX-4 - #if ENABLED(NEWPANEL) - #if ENABLED(REPRAPWORLD_KEYPAD) - #define SHIFT_OUT P0_18 // (51) (MOSI) J3-10 & AUX-3 - #define SHIFT_CLK P0_15 // (52) (SCK) J3-9 & AUX-3 - #define SHIFT_LD P1_31 // (49) not 5V tolerant J3-1 & AUX-3 - #endif - #else - //#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4 - //#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4 - //#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4 - //#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4 + #define DOGLCD_CS P0_16 // (16) + #define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2 + #define DOGLCD_SCK SCK_PIN + #define DOGLCD_MOSI MOSI_PIN + + #define STAT_LED_BLUE_PIN P0_26 //(63) may change if cable changes + #define STAT_LED_RED_PIN P1_21 // ( 6) may change if cable changes + #else + #define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2 + #define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2 + #define LCD_BACKLIGHT_PIN P0_16 //(16) J3-7 & AUX-4 - only used on DOGLCD controllers + #define LCD_PINS_ENABLE P0_18 // (51) (MOSI) J3-10 & AUX-3 + #define LCD_PINS_D4 P0_15 // (52) (SCK) J3-9 & AUX-3 + #if ENABLED(ULTIPANEL) + #define LCD_PINS_D5 P1_17 // (71) ENET_MDIO + #define LCD_PINS_D6 P1_14 // (73) ENET_RX_ER + #define LCD_PINS_D7 P1_10 // (75) ENET_RXD1 #endif + #endif - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - // #define LCD_SCREEN_ROT_180 - - #define BTN_EN1 P3_26 // (31) J3-2 & AUX-4 - #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4 - #define BTN_ENC P2_11 // (35) J3-3 & AUX-4 - - #define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3 - #define KILL_PIN P1_22 // (41) J5-4 & AUX-4 - - #define DOGLCD_CS P0_16 // (16) - #define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2 - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - - #define STAT_LED_BLUE_PIN P0_26 // (63) may change if cable changes - #define STAT_LED_RED_PIN P1_21 // ( 6) may change if cable changes - #else - #define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2 - #define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2 - #define LCD_BACKLIGHT_PIN P0_16 // (16) J3-7 & AUX-4 - only used on DOGLCD controllers - #define LCD_PINS_ENABLE P0_18 // (51) (MOSI) J3-10 & AUX-3 - #define LCD_PINS_D4 P0_15 // (52) (SCK) J3-9 & AUX-3 - #if ENABLED(ULTIPANEL) - #define LCD_PINS_D5 P1_17 // (71) ENET_MDIO - #define LCD_PINS_D6 P1_14 // (73) ENET_RX_ER - #define LCD_PINS_D7 P1_10 // (75) ENET_RXD1 - #endif - #endif - - //#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3 - //#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3 - //#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3 - //#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 - sometimes called SDSS - - #if ENABLED(MINIPANEL) - // GLCD features - //#define LCD_CONTRAST 190 - // Uncomment screen orientation - //#define LCD_SCREEN_ROT_90 - //#define LCD_SCREEN_ROT_180 - //#define LCD_SCREEN_ROT_270 - #endif + //#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3 + //#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3 + //#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3 + //#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS) + #if ENABLED(MINIPANEL) + // GLCD features + //#define LCD_CONTRAST 190 + // Uncomment screen orientation + //#define LCD_SCREEN_ROT_90 + //#define LCD_SCREEN_ROT_180 + //#define LCD_SCREEN_ROT_270 #endif #endif // ULTRA_LCD @@ -349,17 +340,17 @@ // Ethernet pins // #if DISABLED(ULTIPANEL) - #define ENET_MDIO P1_17 // (71) J12-4 - #define ENET_RX_ER P1_14 // (73) J12-6 - #define ENET_RXD1 P1_10 // (75) J12-8 + #define ENET_MDIO P1_17 // (71) J12-4 + #define ENET_RX_ER P1_14 // (73) J12-6 + #define ENET_RXD1 P1_10 // (75) J12-8 #endif -#define ENET_MOC P1_16 // (70) J12-3 -#define REF_CLK P1_15 // (72) J12-5 -#define ENET_RXD0 P1_09 // (74) J12-7 -#define ENET_CRS P1_08 // (76) J12-9 -#define ENET_TX_EN P1_04 // (77) J12-10 -#define ENET_TXD0 P1_00 // (78) J12-11 -#define ENET_TXD1 P1_01 // (79) J12-12 +#define ENET_MOC P1_16 // (70) J12-3 +#define REF_CLK P1_15 // (72) J12-5 +#define ENET_RXD0 P1_09 // (74) J12-7 +#define ENET_CRS P1_08 // (76) J12-9 +#define ENET_TX_EN P1_04 // (77) J12-10 +#define ENET_TXD0 P1_00 // (78) J12-11 +#define ENET_TXD1 P1_01 // (79) J12-12 //#define USB_SD_DISABLED #define USB_SD_ONBOARD // Provide the onboard SD card to the host as a USB mass storage device @@ -369,11 +360,11 @@ #if ENABLED(LPC_SD_LCD) - #define SCK_PIN P0_15 - #define MISO_PIN P0_17 - #define MOSI_PIN P0_18 - #define SS_PIN P1_23 // Chip select for SD card used by Marlin - #define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card + #define SCK_PIN P0_15 + #define MISO_PIN P0_17 + #define MOSI_PIN P0_18 + #define SS_PIN P1_23 // Chip select for SD card used by Marlin + #define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card #elif ENABLED(LPC_SD_ONBOARD) @@ -383,66 +374,51 @@ #define SHARED_SD_CARD #undef SD_DETECT_PIN // there is also no detect pin for the onboard card #endif - #define SCK_PIN P0_07 - #define MISO_PIN P0_08 - #define MOSI_PIN P0_09 - #define SS_PIN P0_06 // Chip select for SD card used by Marlin - #define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card + + #define SCK_PIN P0_07 + #define MISO_PIN P0_08 + #define MOSI_PIN P0_09 + #define SS_PIN P0_06 // Chip select for SD card used by Marlin + #define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card #endif /** * Fast PWMs * - * The LPC1768's hardware PWM controller has 6 channels. Each channel + * The LPC1768's hardware PWM controller has 6 channels. Each channel * can be setup to either control a dedicated pin directly or to generate - * an interrupt. The direct method's duty cycle is accurate to within a - * a microsecond. The interrupt method's average duty cycle has the + * an interrupt. The direct method's duty cycle is accurate to within a + * a microsecond. The interrupt method's average duty cycle has the * the same accuracy but the individual cycles can vary because of higher * priority interrupts. * * All Fast PWMs have a 50Hz rate. * - * The following pins/signals use the direct method. All other pins use the + * The following pins/signals use the direct method. All other pins use the * the interrupt method. Note that SERVO2_PIN and RAMPS_D8_PIN use the * interrupt method. + * * P1_20 (11) SERVO0_PIN * P1_21 ( 6) SERVO1_PIN J5-1 * P0_18 ( 4) SERVO3_PIN 5V output * *P2_04 ( 9) RAMPS_D9_PIN * *P2_05 (10) RAMPS_D10_PIN * - * * - If used as a heater driver then a Fast PWM is NOT assigned. If used as + * * - If used as a heater driver then a Fast PWM is NOT assigned. If used as * a fan driver then enabling FAST_PWM_FAN assigns a Fast PWM to it. */ /** * Special pins - * P1_30 (37) - not 5V tolerant - * P1_31 (49) - not 5V tolerant - * P0_27 (57) - open collector - * P0_28 (58) - open collector - * - */ + * P1_30 (37) (NOT 5V tolerant) + * P1_31 (49) (NOT 5V tolerant) + * P0_27 (57) (Open collector) + * P0_28 (58) (Open collector) + */ /** - * The following mega2560 pins are NOT available in a Re-ARM system - * 7 - * 17 - * 22 - * 23 - * 25 - * 27 - * 29 - * 32 - * 39 - * 40 - * 42 - * 43 - * 44 - * 45 - * 47 - * 64 - * 65 - * 66 + * The following mega2560 pins are NOT available in a Re-ARM system: + * + * 7, 17, 22, 23, 25, 27, 29, 32, 39, 40, 42, 43, 44, 45, 47, 64, 65, 66 */