Merge pull request #2868 from esenapaj/esenapaj-patch-1

Fix AUTOTEMP documentation in configs
9 years ago · b03787262a
parent 159ff94afd 27d918d836
commit b03787262a
11 changed files with 110 additions and 198 deletions
--- a/Marlin/example_configurations/Felix/Configuration_adv.h
+++ b/Marlin/example_configurations/Felix/Configuration_adv.h
@ -36,16 +36,6 @@
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif

-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
  // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
  #endif
 #endif

-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
  #define AUTOTEMP_OLDWEIGHT 0.98
--- a/Marlin/example_configurations/Hephestos/Configuration_adv.h
+++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h
@ -36,16 +36,6 @@
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif

-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
  // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
  #endif
 #endif

-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
  #define AUTOTEMP_OLDWEIGHT 0.98
--- a/Marlin/example_configurations/K8200/Configuration_adv.h
+++ b/Marlin/example_configurations/K8200/Configuration_adv.h
@ -36,16 +36,6 @@
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif

-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
  // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
  #endif
 #endif

-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
  #define AUTOTEMP_OLDWEIGHT 0.98
--- a/Marlin/example_configurations/SCARA/Configuration_adv.h
+++ b/Marlin/example_configurations/SCARA/Configuration_adv.h
@ -36,16 +36,6 @@
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif

-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
  // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
  #endif
 #endif

-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
  #define AUTOTEMP_OLDWEIGHT 0.98
--- a/Marlin/example_configurations/WITBOX/Configuration_adv.h
+++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h
@ -36,16 +36,6 @@
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif

-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
  // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
  #endif
 #endif

-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
  #define AUTOTEMP_OLDWEIGHT 0.98
--- a/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
@ -36,16 +36,6 @@
  #define THERMAL_PROTECTION_BED_HYSTERESIS 4 // Degrees Celsius
 #endif

-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
  // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
  #endif
 #endif

-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
  #define AUTOTEMP_OLDWEIGHT 0.98
--- a/Marlin/example_configurations/delta/generic/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h
@ -36,16 +36,6 @@
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif

-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
  // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
  #endif
 #endif

-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
  #define AUTOTEMP_OLDWEIGHT 0.98
--- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
@ -36,16 +36,6 @@
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif

-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
  // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
  #endif
 #endif

-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
  #define AUTOTEMP_OLDWEIGHT 0.98
--- a/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
@ -40,16 +40,6 @@
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif

-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
  // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -60,14 +50,16 @@
  #endif
 #endif

-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
  #define AUTOTEMP_OLDWEIGHT 0.98
--- a/Marlin/example_configurations/makibox/Configuration_adv.h
+++ b/Marlin/example_configurations/makibox/Configuration_adv.h
@ -36,16 +36,6 @@
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif

-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
  // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
  #endif
 #endif

-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
  #define AUTOTEMP_OLDWEIGHT 0.98
--- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
@ -36,16 +36,6 @@
  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 #endif

-/**
- * Automatic Temperature:
- * The hotend target temperature is calculated by all the buffered lines of gcode.
- * The maximum buffered steps/sec of the extruder motor is called "se".
- * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
- * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
- * mintemp and maxtemp. Turn this off by excuting M109 without F*
- * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
- * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
- */
 #if ENABLED(PIDTEMP)
  // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
@ -56,14 +46,16 @@
  #endif
 #endif

-
-//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
-//The maximum buffered steps/sec of the extruder motor are called "se".
-//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
-// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
-// you exit the value by any M109 without F*
-// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
-// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by excuting M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
 #define AUTOTEMP
 #if ENABLED(AUTOTEMP)
  #define AUTOTEMP_OLDWEIGHT 0.98