Reorder RAMBo tests

buildroot/share/tests/rambo-tests

@@ -6,33 +6,6 @@
 # exit on first failure
 set -e
 
-#
-# Build with the default configurations
-#
-restore_configs
-opt_set MOTHERBOARD BOARD_EINSY_RAMBO
-opt_set X_DRIVER_TYPE TMC2130
-opt_set Y_DRIVER_TYPE TMC2130
-opt_set Z_DRIVER_TYPE TMC2130
-opt_set E0_DRIVER_TYPE TMC2130
-exec_test $1 $2 "Default Configuration"
-
-#
-# Full size Rambo Dual Endstop CNC
-#
-restore_configs
-opt_set MOTHERBOARD BOARD_RAMBO
-opt_set EXTRUDERS 0
-opt_set TEMP_SENSOR_0 999
-opt_set DUMMY_THERMISTOR_999_VALUE 170
-opt_set DIGIPOT_MOTOR_CURRENT '{ 120, 120, 120, 120, 120 }'
-opt_enable USE_XMAX_PLUG USE_YMAX_PLUG USE_ZMAX_PLUG \
-           REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER REVERSE_ENCODER_DIRECTION SDSUPPORT EEPROM_SETTINGS \
-           S_CURVE_ACCELERATION X_DUAL_STEPPER_DRIVERS X_DUAL_ENDSTOPS Y_DUAL_STEPPER_DRIVERS Y_DUAL_ENDSTOPS \
-           ADAPTIVE_STEP_SMOOTHING CNC_COORDINATE_SYSTEMS GCODE_MOTION_MODES
-opt_disable MIN_SOFTWARE_ENDSTOP_Z MAX_SOFTWARE_ENDSTOPS
-exec_test $1 $2 "Rambo CNC Configuration"
-
 #
 # Lots of options - Formerly the first Mega2560 test
 #
@@ -68,5 +41,32 @@ opt_enable REPRAP_DISCOUNT_SMART_CONTROLLER LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TE
            HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT PINS_DEBUGGING MAX7219_DEBUG M114_DETAIL
 exec_test $1 $2 "RAMBO | EXTRUDERS 2 | CHAR LCD + SD | FIX Probe | ABL-Linear | Advanced Pause | PLR | LEDs ..."
 
+#
+# Full size Rambo Dual Endstop CNC
+#
+restore_configs
+opt_set MOTHERBOARD BOARD_RAMBO
+opt_set EXTRUDERS 0
+opt_set TEMP_SENSOR_0 999
+opt_set DUMMY_THERMISTOR_999_VALUE 170
+opt_set DIGIPOT_MOTOR_CURRENT '{ 120, 120, 120, 120, 120 }'
+opt_enable USE_XMAX_PLUG USE_YMAX_PLUG USE_ZMAX_PLUG \
+           REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER REVERSE_ENCODER_DIRECTION SDSUPPORT EEPROM_SETTINGS \
+           S_CURVE_ACCELERATION X_DUAL_STEPPER_DRIVERS X_DUAL_ENDSTOPS Y_DUAL_STEPPER_DRIVERS Y_DUAL_ENDSTOPS \
+           ADAPTIVE_STEP_SMOOTHING CNC_COORDINATE_SYSTEMS GCODE_MOTION_MODES
+opt_disable MIN_SOFTWARE_ENDSTOP_Z MAX_SOFTWARE_ENDSTOPS
+exec_test $1 $2 "Rambo CNC Configuration"
+
+#
+# Build with the default configurations
+#
+restore_configs
+opt_set MOTHERBOARD BOARD_EINSY_RAMBO
+opt_set X_DRIVER_TYPE TMC2130
+opt_set Y_DRIVER_TYPE TMC2130
+opt_set Z_DRIVER_TYPE TMC2130
+opt_set E0_DRIVER_TYPE TMC2130
+exec_test $1 $2 "Einsy RAMBo with TMC2130"
+
 # clean up
 restore_configs