Update copyright in header, etc. (#14645)

5 years ago · abc9b52692
parent 5535a047d7
commit abc9b52692
6 changed files with 77 additions and 64 deletions
--- a/Marlin/src/pins/lpc1768/pins_MKS_SBASE.h
+++ b/Marlin/src/pins/lpc1768/pins_MKS_SBASE.h
@ -260,7 +260,7 @@
        #define RGB_LED_B_PIN P1_22        // J8-2  (LCD_D7 on Fysetc schematic)
      #endif
    #elif ENABLED(FYSETC_MINI_12864_2_1)
-      #define NEOPIXEL_PIN    P2_12
+      #define NEOPIXEL_PIN P2_12
    #endif

  #elif ENABLED(MINIPANEL)
@ -304,9 +304,14 @@
 #endif

 #if MB(MKS_SBASE) && HAS_TMC220x
-  // The shortage of pins becomes apparent.
-  // Worst case you may have to give up the LCD
-  // RX pins need to be interrupt capable
+
+  /**
+   * TMC2208/TMC2209 stepper drivers
+   *
+   * The shortage of pins becomes apparent.
+   * Worst case you may have to give up the LCD
+   * RX pins need to be interrupt capable
+   */
  #define X_SERIAL_TX_PIN  P1_22   // J8-2
  #define X_SERIAL_RX_PIN  P2_12   // J8-4 Interrupt Capable
  #define Y_SERIAL_TX_PIN  P1_23   // J8-3
@ -344,26 +349,26 @@
 *  PWM1.6   P2_05   RAMPS_D10_PIN
 */

- /**
-  * Special pins
-  *   P1_30 - not 5V tolerant - EXP1
-  *   P1_31 - not 5V tolerant - EXP1
-  *   P0_27 - open collector  - EXP2
-  *   P0_28 - open collector  - EXP2
-  *
-  */
+/**
+ * Special pins
+ *   P1_30 - not 5V tolerant - EXP1
+ *   P1_31 - not 5V tolerant - EXP1
+ *   P0_27 - open collector  - EXP2
+ *   P0_28 - open collector  - EXP2
+ *
+ */

- /**
-  * Serial Ports
-  *   P0_00 - Port  3
-  *   P0_01 - SD Card (Onboard)
-  *   P0_10 - Port  2
-  *   P0_11 - Y_EN/Y_DIR
-  *   P0_15 - Port  1
-  *   P0_16 - EXP1
-  *   P0_02 - Port  0
-  *   P0_03 - AUX1
-  *   P0_29 - Port -1
-  *   P0_30 - USB
-  *
-  */
+/**
+ * Serial Ports
+ *   P0_00 - Port  3
+ *   P0_01 - SD Card (Onboard)
+ *   P0_10 - Port  2
+ *   P0_11 - Y_EN/Y_DIR
+ *   P0_15 - Port  1
+ *   P0_16 - EXP1
+ *   P0_02 - Port  0
+ *   P0_03 - AUX1
+ *   P0_29 - Port -1
+ *   P0_30 - USB
+ *
+ */
--- a/Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h
+++ b/Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h
@ -110,7 +110,7 @@

 #if HAS_TMC220x
  /**
-   * TMC2208 stepper drivers
+   * TMC2208/TMC2209 stepper drivers
   *
   * Hardware serial communication ports.
   * If undefined software serial is used according to the pins below
--- a/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h
+++ b/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h
@ -121,24 +121,24 @@
   * If undefined software serial is used according to the pins below
   */

-  /**
-   * Software serial
-   */
+  //
+  // Software serial
+  //

-   // P2_08 E1-Step
-   // P2_13 E1-Dir
+  // P2_08 E1-Step
+  // P2_13 E1-Dir

-  #define X_SERIAL_TX_PIN    P2_13
-  #define X_SERIAL_RX_PIN    P2_13
+  #define X_SERIAL_TX_PIN  P2_13
+  #define X_SERIAL_RX_PIN  P2_13

-  #define Y_SERIAL_TX_PIN    P0_00
-  #define Y_SERIAL_RX_PIN    P0_00
+  #define Y_SERIAL_TX_PIN  P0_00
+  #define Y_SERIAL_RX_PIN  P0_00

-  #define Z_SERIAL_TX_PIN    P0_01
-  #define Z_SERIAL_RX_PIN    P0_01
+  #define Z_SERIAL_TX_PIN  P0_01
+  #define Z_SERIAL_RX_PIN  P0_01

-  #define E0_SERIAL_TX_PIN   P2_08
-  #define E0_SERIAL_RX_PIN   P2_08
+  #define E0_SERIAL_TX_PIN P2_08
+  #define E0_SERIAL_RX_PIN P2_08

 #endif

@ -254,9 +254,9 @@
      #error "LASER_FEATURE requires 3 free servo pins."
    #endif
  #endif
-  #define SPINDLE_LASER_ENA_PIN    SERVO1_PIN   // (6) Pin should have a pullup/pulldown!
-  #define SPINDLE_LASER_PWM_PIN    SERVO3_PIN   // (4) MUST BE HARDWARE PWM
-  #define SPINDLE_DIR_PIN          SERVO2_PIN   // (5)
+  #define SPINDLE_LASER_ENA_PIN SERVO1_PIN   // (6) Pin should have a pullup/pulldown!
+  #define SPINDLE_LASER_PWM_PIN SERVO3_PIN   // (4) MUST BE HARDWARE PWM
+  #define SPINDLE_DIR_PIN       SERVO2_PIN   // (5)
 #endif

 //
@ -309,10 +309,10 @@

 #elif HAS_SPI_LCD

-  //#define SCK_PIN        P0_15   // (52)  system defined J3-9 & AUX-3
-  //#define MISO_PIN       P0_17   // (50)  system defined J3-10 & AUX-3
-  //#define MOSI_PIN       P0_18   // (51)  system defined J3-10 & AUX-3
-  //#define SS_PIN         P1_23   // (53)  system defined J3-5 & AUX-3 (Sometimes called SDSS)
+  //#define SCK_PIN          P0_15   // (52)  system defined J3-9 & AUX-3
+  //#define MISO_PIN         P0_17   // (50)  system defined J3-10 & AUX-3
+  //#define MOSI_PIN         P0_18   // (51)  system defined J3-10 & AUX-3
+  //#define SS_PIN           P1_23   // (53)  system defined J3-5 & AUX-3 (Sometimes called SDSS)

  #if ENABLED(FYSETC_MINI_12864)
    #define BEEPER_PIN     P1_01
@ -337,10 +337,10 @@
      #define SHIFT_LD     P1_31   // (49)        J3-1 & AUX-3 (NOT 5V tolerant)
    #endif
  #else
-    //#define SHIFT_CLK    P3_26   // (31)  J3-2 & AUX-4
-    //#define SHIFT_LD     P3_25   // (33)  J3-4 & AUX-4
-    //#define SHIFT_OUT    P2_11   // (35)  J3-3 & AUX-4
-    //#define SHIFT_EN     P1_22   // (41)  J5-4 & AUX-4
+    //#define SHIFT_CLK      P3_26   // (31)  J3-2 & AUX-4
+    //#define SHIFT_LD       P3_25   // (33)  J3-4 & AUX-4
+    //#define SHIFT_OUT      P2_11   // (35)  J3-3 & AUX-4
+    //#define SHIFT_EN       P1_22   // (41)  J5-4 & AUX-4
  #endif

  #if ANY(VIKI2, miniVIKI)
@ -365,7 +365,7 @@
      //#define FORCE_SOFT_SPI    // Use this if default of hardware SPI causes display problems
                                  //   results in LCD soft SPI mode 3, SD soft SPI mode 0

-      #define LCD_RESET_PIN  P0_16   // Must be high or open for LCD to operate normally.
+      #define LCD_RESET_PIN P0_16   // Must be high or open for LCD to operate normally.

      #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
        #ifndef RGB_LED_R_PIN
@ -378,7 +378,7 @@
          #define RGB_LED_B_PIN P1_08
        #endif
      #elif ENABLED(FYSETC_MINI_12864_2_1)
-        #define NEOPIXEL_PIN    P1_00
+        #define NEOPIXEL_PIN P1_00
      #endif
    #else
      #define DOGLCD_CS    P0_26   // (63) J5-3 & AUX-2
--- a/Marlin/src/pins/lpc1769/pins_MKS_SGEN.h
+++ b/Marlin/src/pins/lpc1769/pins_MKS_SGEN.h
@ -40,13 +40,17 @@

 //#undef BTN_EN1
 //#undef BTN_EN2
-//#define BTN_EN1        P1_23   // EXP2.5
-//#define BTN_EN2        P1_22   // EXP2.3
+//#define BTN_EN1            P1_23   // EXP2.5
+//#define BTN_EN2            P1_22   // EXP2.3

 #if HAS_TMC220x
-  // The shortage of pins becomes apparent.
-  // In the worst case you may have to give up the LCD.
-  // RX pins must be interrupt-capable.
+  /**
+   * TMC2208/TMC2209 stepper drivers
+   *
+   * The shortage of pins becomes apparent.
+   * In the worst case you may have to give up the LCD.
+   * RX pins must be interrupt-capable.
+   */
  #define X_SERIAL_TX_PIN  P4_29   // J8-2
  #define X_SERIAL_RX_PIN  P4_29   // J8-2

--- a/Marlin/src/pins/ramps/pins_FYSETC_F6_13.h
+++ b/Marlin/src/pins/ramps/pins_FYSETC_F6_13.h
@ -118,8 +118,12 @@
 //

 #if HAS_TMC220x
-  // Software serial
-  // At the moment, F6 rx pins are not pc interrupt pins
+  /**
+   * TMC2208/TMC2209 stepper drivers
+   *
+   * Software serial communication pins.
+   * At the moment, F6 rx pins are not pc interrupt pins
+   */
  #define X_SERIAL_RX_PIN  -1   // 71
  #define X_SERIAL_TX_PIN  72
  #define Y_SERIAL_RX_PIN  -1   // 73
--- a/Marlin/src/pins/ramps/pins_TT_OSCAR.h
+++ b/Marlin/src/pins/ramps/pins_TT_OSCAR.h
@ -1,9 +1,9 @@
 /**
 * Marlin 3D Printer Firmware
- * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
- * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
@ -99,9 +99,9 @@
 #define E4_ENABLE_PIN      47
 #define E4_CS_PIN          E0_CS_PIN

-#if ENABLED(HAVE_TMC2208)
+#if HAS_TMC220x
  /**
-   * TMC2208 stepper drivers
+   * TMC2208/TMC2209 stepper drivers
   *
   * Hardware serial communication ports.
   * If undefined software serial is used according to the pins below