Anet ET4 / ET4P and Anet TFT28 / TFT35 (#20280)
Keith Bennett
4 years ago
committed by
Scott Lahteine
parent
59b5cb6fe2
commit
aa65c6e477
@ -0,0 +1,223 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#if NOT_TARGET(STM32F4)
|
||||
#error "Oops! Select an STM32F4 board in 'Tools > Board.'"
|
||||
#elif HOTENDS > 1 || E_STEPPERS > 1
|
||||
#error "Anet ET4 only supports one hotend / E-stepper. Comment out this line to continue."
|
||||
#endif
|
||||
|
||||
#ifndef BOARD_INFO_NAME
|
||||
#define BOARD_INFO_NAME "Anet ET4 1.x"
|
||||
#endif
|
||||
|
||||
//
|
||||
// EEPROM
|
||||
//
|
||||
|
||||
// Use one of these or SDCard-based Emulation will be used
|
||||
#if NO_EEPROM_SELECTED
|
||||
//#define SRAM_EEPROM_EMULATION // Use BackSRAM-based EEPROM emulation
|
||||
#define FLASH_EEPROM_EMULATION // Use Flash-based EEPROM emulation
|
||||
//#define IIC_BL24CXX_EEPROM // Use I2C EEPROM onboard IC (AT24C04C, Size 4KB, PageSize 16B)
|
||||
#endif
|
||||
|
||||
#if ENABLED(FLASH_EEPROM_EMULATION)
|
||||
// Decrease delays and flash wear by spreading writes across the
|
||||
// 128 kB sector allocated for EEPROM emulation.
|
||||
#define FLASH_EEPROM_LEVELING
|
||||
#elif ENABLED(IIC_BL24CXX_EEPROM)
|
||||
#define IIC_EEPROM_SDA PB11
|
||||
#define IIC_EEPROM_SCL PB10
|
||||
#define EEPROM_DEVICE_ADDRESS 0xA0
|
||||
#define MARLIN_EEPROM_SIZE 0x1000 // 4KB
|
||||
#endif
|
||||
|
||||
//
|
||||
// Limit Switches
|
||||
//
|
||||
#define X_STOP_PIN PC13
|
||||
#define Y_STOP_PIN PE12
|
||||
#define Z_STOP_PIN PE11
|
||||
|
||||
//
|
||||
// Z Probe
|
||||
//
|
||||
#if ENABLED(BLTOUCH)
|
||||
#error "You will need to use 24V to 5V converter and remove one resistor and capacitor from the motherboard. See https://github.com/davidtgbe/Marlin/blob/bugfix-2.0.x/docs/Tutorials/bltouch-en.md for more information. Comment out this line to proceed at your own risk."
|
||||
#define SERVO0_PIN PC3
|
||||
#elif !defined(Z_MIN_PROBE_PIN)
|
||||
#define Z_MIN_PROBE_PIN PC3
|
||||
#endif
|
||||
|
||||
//
|
||||
// Filament Runout Sensor
|
||||
//
|
||||
#ifndef FIL_RUNOUT_PIN
|
||||
#define FIL_RUNOUT_PIN PA2
|
||||
#endif
|
||||
|
||||
//
|
||||
// Power Loss Detection
|
||||
//
|
||||
#ifndef POWER_LOSS_PIN
|
||||
#define POWER_LOSS_PIN PA8
|
||||
#endif
|
||||
|
||||
//
|
||||
// LED PIN
|
||||
//
|
||||
#define LED_PIN PD12
|
||||
|
||||
//
|
||||
// Steppers
|
||||
//
|
||||
#define X_STEP_PIN PB6
|
||||
#define X_DIR_PIN PB5
|
||||
#define X_ENABLE_PIN PB7
|
||||
|
||||
#define Y_STEP_PIN PB3
|
||||
#define Y_DIR_PIN PD6
|
||||
#define Y_ENABLE_PIN PB4
|
||||
|
||||
#define Z_STEP_PIN PA12
|
||||
#define Z_DIR_PIN PA11
|
||||
#define Z_ENABLE_PIN PA15
|
||||
|
||||
#define E0_STEP_PIN PB9
|
||||
#define E0_DIR_PIN PB8
|
||||
#define E0_ENABLE_PIN PE0
|
||||
|
||||
//
|
||||
// Temperature Sensors
|
||||
//
|
||||
#define TEMP_0_PIN PA1
|
||||
#define TEMP_BED_PIN PA4
|
||||
|
||||
//
|
||||
// Heaters
|
||||
//
|
||||
#define HEATER_0_PIN PA0
|
||||
#define HEATER_BED_PIN PE2
|
||||
|
||||
//
|
||||
// Fans
|
||||
//
|
||||
#define FAN_PIN PE3 // Layer fan
|
||||
#define FAN1_PIN PE1 // Hotend fan
|
||||
|
||||
#ifndef E0_AUTO_FAN_PIN
|
||||
#define E0_AUTO_FAN_PIN FAN1_PIN
|
||||
#endif
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
//
|
||||
#define TFT_RESET_PIN PE6
|
||||
#define TFT_CS_PIN PD7
|
||||
#define TFT_RS_PIN PD13
|
||||
#define TFT_INTERFACE_FSMC_8BIT
|
||||
|
||||
//
|
||||
// Touch Screen
|
||||
// https://ldm-systems.ru/f/doc/catalog/HY-TFT-2,8/XPT2046.pdf
|
||||
//
|
||||
#if ENABLED(TOUCH_SCREEN)
|
||||
#define TOUCH_CS_PIN PB2
|
||||
#define TOUCH_SCK_PIN PB0
|
||||
#define TOUCH_MOSI_PIN PE5
|
||||
#define TOUCH_MISO_PIN PE4
|
||||
#define TOUCH_INT_PIN PB1
|
||||
#endif
|
||||
|
||||
// Touchscreen calibration does not work correctly with ANET_ET5_TFT35 or ANET_ET4_TFT28
|
||||
#if ENABLED(TOUCH_SCREEN_CALIBRATION)
|
||||
#undef TOUCH_SCREEN_CALIBRATION
|
||||
#endif
|
||||
|
||||
#if ENABLED(ANET_ET5_TFT35)
|
||||
#ifndef TOUCH_CALIBRATION_X
|
||||
#define TOUCH_CALIBRATION_X 17125
|
||||
#endif
|
||||
#ifndef TOUCH_CALIBRATION_Y
|
||||
#define TOUCH_CALIBRATION_Y -11307
|
||||
#endif
|
||||
#ifndef TOUCH_OFFSET_X
|
||||
#define TOUCH_OFFSET_X -26
|
||||
#endif
|
||||
#ifndef TOUCH_OFFSET_Y
|
||||
#define TOUCH_OFFSET_Y 337
|
||||
#endif
|
||||
#ifndef TOUCH_ORIENTATION
|
||||
#define TOUCH_ORIENTATION TOUCH_PORTRAIT
|
||||
#endif
|
||||
#elif ENABLED(ANET_ET4_TFT28)
|
||||
#ifndef TOUCH_CALIBRATION_X
|
||||
#define TOUCH_CALIBRATION_X -11838
|
||||
#endif
|
||||
#ifndef TOUCH_CALIBRATION_Y
|
||||
#define TOUCH_CALIBRATION_Y 8776
|
||||
#endif
|
||||
#ifndef TOUCH_OFFSET_X
|
||||
#define TOUCH_OFFSET_X 333
|
||||
#endif
|
||||
#ifndef TOUCH_OFFSET_Y
|
||||
#define TOUCH_OFFSET_Y -17
|
||||
#endif
|
||||
#ifndef TOUCH_ORIENTATION
|
||||
#define TOUCH_ORIENTATION TOUCH_PORTRAIT
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//
|
||||
// SD Card
|
||||
//
|
||||
//#define SDIO_SUPPORT
|
||||
|
||||
#ifndef SDCARD_CONNECTION
|
||||
#define SDCARD_CONNECTION CUSTOM_CABLE
|
||||
#endif
|
||||
|
||||
#if ENABLED(SDSUPPORT)
|
||||
|
||||
#define SDIO_D0_PIN PC8
|
||||
#define SDIO_D1_PIN PC9
|
||||
#define SDIO_D2_PIN PC10
|
||||
#define SDIO_D3_PIN PC11
|
||||
#define SDIO_CK_PIN PC12
|
||||
#define SDIO_CMD_PIN PD2
|
||||
|
||||
#if DISABLED(SDIO_SUPPORT)
|
||||
#define SOFTWARE_SPI
|
||||
#define SDSS SDIO_D3_PIN
|
||||
#define SCK_PIN SDIO_CK_PIN
|
||||
#define MISO_PIN SDIO_D0_PIN
|
||||
#define MOSI_PIN SDIO_CMD_PIN
|
||||
#endif
|
||||
|
||||
#ifndef SD_DETECT_PIN
|
||||
#define SD_DETECT_PIN PD3
|
||||
#endif
|
||||
|
||||
#endif
|
||||
@ -0,0 +1,34 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
#pragma once
|
||||
|
||||
#define BOARD_INFO_NAME "Anet ET4P 1.x"
|
||||
|
||||
//
|
||||
// TMC2208 Configuration_adv defaults for Anet ET4P-MB_V1.x
|
||||
//
|
||||
#if !AXIS_DRIVER_TYPE_X(TMC2208_STANDALONE) || !AXIS_DRIVER_TYPE_Y(TMC2208_STANDALONE) || !AXIS_DRIVER_TYPE_Z(TMC2208_STANDALONE) || !AXIS_DRIVER_TYPE_E0(TMC2208_STANDALONE)
|
||||
#error "ANET_ET4P requires ([XYZ]|E0)_DRIVER_TYPE set to TMC2208_STANDALONE."
|
||||
#endif
|
||||
|
||||
#include "pins_ANET_ET4.h"
|
||||
Loading…
Reference in New Issue