Clean up spacing and comments
Also clean up some trailing spaces in a few other sources
This commit is contained in:
Scott Lahteine
Richard Wackerbarth
parent
d3bce05d54
commit
a274769f4f
@ -235,7 +235,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
//#define PIDTEMPBED
|
||||
//
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -406,7 +406,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//=========================== Manual Bed Leveling ===========================
|
||||
@ -498,7 +498,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
|
||||
// #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
|
||||
//Useful to retract a deployable probe.
|
||||
|
||||
|
||||
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
|
||||
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||
|
||||
@ -573,7 +573,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||
|
||||
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
||||
|
||||
@ -235,7 +235,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
//#define PIDTEMPBED
|
||||
//
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -404,7 +404,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//=========================== Manual Bed Leveling ===========================
|
||||
|
||||
@ -214,7 +214,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
#define PIDTEMPBED
|
||||
//
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -355,7 +355,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//=========================== Manual Bed Leveling ===========================
|
||||
|
||||
@ -214,7 +214,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
#define PIDTEMPBED
|
||||
//
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -353,7 +353,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//=========================== Manual Bed Leveling ===========================
|
||||
|
||||
@ -231,7 +231,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
//#define PIDTEMPBED
|
||||
//
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -379,7 +379,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//=========================== Manual Bed Leveling ===========================
|
||||
|
||||
@ -245,7 +245,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
//#define PIDTEMPBED
|
||||
//
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -422,7 +422,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//=========================== Manual Bed Leveling ===========================
|
||||
|
||||
@ -235,7 +235,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
//#define PIDTEMPBED
|
||||
//
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -406,7 +406,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//=========================== Manual Bed Leveling ===========================
|
||||
|
||||
@ -260,7 +260,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
#define PIDTEMPBED
|
||||
//
|
||||
|
||||
#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -414,7 +414,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//=========================== Manual Bed Leveling ===========================
|
||||
|
||||
@ -230,7 +230,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
//#define PIDTEMPBED
|
||||
//
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -378,7 +378,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//=========================== Manual Bed Leveling ===========================
|
||||
|
||||
@ -261,7 +261,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
//#define PIDTEMPBED
|
||||
//
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -385,6 +385,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
#define INVERT_Z_DIR false
|
||||
|
||||
// @section extruder
|
||||
|
||||
// For direct drive extruder v9 set to true, for geared extruder set to false.
|
||||
#define INVERT_E0_DIR false
|
||||
#define INVERT_E1_DIR false
|
||||
#define INVERT_E2_DIR false
|
||||
@ -430,7 +432,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
// #define MESH_BED_LEVELING // Enable mesh bed leveling
|
||||
|
||||
#ifdef MANUAL_BED_LEVELING
|
||||
#define MBL_Z_STEP 0.025
|
||||
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis
|
||||
#endif // MANUAL_BED_LEVELING
|
||||
|
||||
#ifdef MESH_BED_LEVELING
|
||||
@ -471,13 +473,13 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID
|
||||
|
||||
// set the rectangle in which to probe
|
||||
#define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
|
||||
|
||||
#define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
|
||||
#define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
|
||||
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
|
||||
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
|
||||
|
||||
|
||||
#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
|
||||
|
||||
// Non-linear bed leveling will be used.
|
||||
@ -516,13 +518,14 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
|
||||
// #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
|
||||
//Useful to retract a deployable probe.
|
||||
|
||||
|
||||
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
|
||||
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||
|
||||
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
|
||||
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
||||
//#define Z_PROBE_ALLEN_KEY
|
||||
|
||||
#ifdef Z_PROBE_ALLEN_KEY
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_X 30
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_Y DELTA_PRINTABLE_RADIUS
|
||||
@ -533,7 +536,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_Z 23
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_DEPTH 20
|
||||
#endif
|
||||
|
||||
|
||||
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
|
||||
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
|
||||
// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
|
||||
@ -595,7 +598,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
* MOVEMENT SETTINGS
|
||||
*/
|
||||
|
||||
|
||||
// delta homing speeds must be the same on xyz
|
||||
#define HOMING_FEEDRATE {200*30, 200*30, 200*30, 0} // set the homing speeds (mm/min)
|
||||
|
||||
@ -606,7 +608,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
||||
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
@ -649,7 +651,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
|
||||
#ifdef EEPROM_SETTINGS
|
||||
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
||||
#define EEPROM_CHITCHAT // please keep turned on if you can.
|
||||
#define EEPROM_CHITCHAT // Please keep turned on if you can.
|
||||
#endif
|
||||
|
||||
// @section temperature
|
||||
@ -667,7 +669,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
// @section lcd
|
||||
|
||||
// Define your display language below. Replace (en) with your language code and uncomment.
|
||||
// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test
|
||||
// en, pl, fr, de, es, ru, bg, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test
|
||||
// See also language.h
|
||||
#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
|
||||
@ -690,7 +692,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
|
||||
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
|
||||
// 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
|
||||
|
||||
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
|
||||
// http://reprap.org/wiki/PanelOne
|
||||
//#define PANEL_ONE
|
||||
@ -758,7 +759,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
|
||||
// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
|
||||
//#define SAV_3DLCD
|
||||
|
||||
// @section extras
|
||||
@ -786,7 +787,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
|
||||
// #define PHOTOGRAPH_PIN 23
|
||||
|
||||
// SF send wrong arc g-codes when using Arc Point as fillet procedure
|
||||
// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
|
||||
//#define SF_ARC_FIX
|
||||
|
||||
// Support for the BariCUDA Paste Extruder.
|
||||
|
||||
@ -261,7 +261,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
//#define PIDTEMPBED
|
||||
//
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -385,6 +385,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
#define INVERT_Z_DIR false
|
||||
|
||||
// @section extruder
|
||||
|
||||
// For direct drive extruder v9 set to true, for geared extruder set to false.
|
||||
#define INVERT_E0_DIR false
|
||||
#define INVERT_E1_DIR false
|
||||
#define INVERT_E2_DIR false
|
||||
@ -423,8 +425,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//=========================== Manual Bed Leveling ===========================
|
||||
//===========================================================================
|
||||
@ -433,7 +435,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
// #define MESH_BED_LEVELING // Enable mesh bed leveling
|
||||
|
||||
#ifdef MANUAL_BED_LEVELING
|
||||
#define MBL_Z_STEP 0.025
|
||||
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis
|
||||
#endif // MANUAL_BED_LEVELING
|
||||
|
||||
#ifdef MESH_BED_LEVELING
|
||||
@ -474,13 +476,13 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID
|
||||
|
||||
// set the rectangle in which to probe
|
||||
#define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
|
||||
|
||||
#define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
|
||||
#define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
|
||||
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
|
||||
#define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
|
||||
|
||||
|
||||
#define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
|
||||
|
||||
// Non-linear bed leveling will be used.
|
||||
@ -519,13 +521,14 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
|
||||
// #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
|
||||
//Useful to retract a deployable probe.
|
||||
|
||||
|
||||
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
|
||||
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||
|
||||
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
|
||||
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
||||
//#define Z_PROBE_ALLEN_KEY
|
||||
|
||||
#ifdef Z_PROBE_ALLEN_KEY
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_X 30
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_Y DELTA_PRINTABLE_RADIUS
|
||||
@ -536,7 +539,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_Z 23
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_DEPTH 20
|
||||
#endif
|
||||
|
||||
|
||||
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
|
||||
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
|
||||
// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
|
||||
@ -598,7 +601,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
* MOVEMENT SETTINGS
|
||||
*/
|
||||
|
||||
|
||||
// delta homing speeds must be the same on xyz
|
||||
#define HOMING_FEEDRATE {200*60, 200*60, 200*60, 0} // set the homing speeds (mm/min)
|
||||
|
||||
@ -609,7 +611,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
||||
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
@ -621,7 +623,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
||||
#define DEFAULT_XYJERK 20.0 // (mm/sec)
|
||||
#define DEFAULT_ZJERK 20.0 // (mm/sec) Must be same as XY for delta
|
||||
#define DEFAULT_EJERK 5.0 // (mm/sec)
|
||||
#define DEFAULT_EJERK 5.0 // (mm/sec)
|
||||
|
||||
|
||||
//=============================================================================
|
||||
@ -652,7 +654,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
|
||||
#ifdef EEPROM_SETTINGS
|
||||
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
||||
#define EEPROM_CHITCHAT // please keep turned on if you can.
|
||||
#define EEPROM_CHITCHAT // Please keep turned on if you can.
|
||||
#endif
|
||||
|
||||
// @section temperature
|
||||
@ -693,7 +695,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
|
||||
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
|
||||
// 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
|
||||
|
||||
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
|
||||
// http://reprap.org/wiki/PanelOne
|
||||
//#define PANEL_ONE
|
||||
@ -761,7 +762,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
|
||||
// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
|
||||
//#define SAV_3DLCD
|
||||
|
||||
// @section extras
|
||||
@ -789,7 +790,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
|
||||
// #define PHOTOGRAPH_PIN 23
|
||||
|
||||
// SF send wrong arc g-codes when using Arc Point as fillet procedure
|
||||
// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
|
||||
//#define SF_ARC_FIX
|
||||
|
||||
// Support for the BariCUDA Paste Extruder.
|
||||
|
||||
@ -261,7 +261,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
//#define PIDTEMPBED
|
||||
//
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -435,7 +435,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
// #define MESH_BED_LEVELING // Enable mesh bed leveling
|
||||
|
||||
#ifdef MANUAL_BED_LEVELING
|
||||
#define MBL_Z_STEP 0.025
|
||||
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis
|
||||
#endif // MANUAL_BED_LEVELING
|
||||
|
||||
#ifdef MESH_BED_LEVELING
|
||||
@ -476,8 +476,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID
|
||||
|
||||
// set the rectangle in which to probe
|
||||
#define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
|
||||
|
||||
#define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
|
||||
#define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
|
||||
#define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
|
||||
@ -525,14 +525,12 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
|
||||
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||
|
||||
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
|
||||
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
|
||||
// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
|
||||
|
||||
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
|
||||
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
||||
#define Z_PROBE_ALLEN_KEY
|
||||
#ifdef Z_PROBE_ALLEN_KEY
|
||||
// 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
|
||||
// if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
|
||||
|
||||
// Kossel Mini
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30.0
|
||||
@ -624,7 +622,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
* MOVEMENT SETTINGS
|
||||
*/
|
||||
|
||||
|
||||
// delta homing speeds must be the same on xyz
|
||||
#define HOMING_FEEDRATE {200*60, 200*60, 200*60, 0} // set the homing speeds (mm/min)
|
||||
|
||||
@ -635,7 +632,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
||||
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
|
||||
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
@ -678,7 +675,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
|
||||
#ifdef EEPROM_SETTINGS
|
||||
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
||||
#define EEPROM_CHITCHAT // please keep turned on if you can.
|
||||
#define EEPROM_CHITCHAT // Please keep turned on if you can.
|
||||
#endif
|
||||
|
||||
// @section temperature
|
||||
@ -719,7 +716,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
|
||||
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
|
||||
// 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
|
||||
|
||||
// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
|
||||
// http://reprap.org/wiki/PanelOne
|
||||
#define PANEL_ONE
|
||||
@ -787,7 +783,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
|
||||
// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
|
||||
//#define SAV_3DLCD
|
||||
|
||||
// @section extras
|
||||
@ -815,7 +811,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
|
||||
// #define PHOTOGRAPH_PIN 23
|
||||
|
||||
// SF send wrong arc g-codes when using Arc Point as fillet procedure
|
||||
// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
|
||||
//#define SF_ARC_FIX
|
||||
|
||||
// Support for the BariCUDA Paste Extruder.
|
||||
|
||||
@ -204,13 +204,12 @@ Here are some standard links for getting your machine calibrated:
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
//#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with gcode: M301 E[extruder number, 0-2]
|
||||
#define PID_FUNCTIONAL_RANGE 50 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
#define PID_FUNCTIONAL_RANGE 50 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
#define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
|
||||
#define K1 0.95 //smoothing factor within the PID
|
||||
|
||||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
|
||||
// Ultimaker
|
||||
// #define DEFAULT_Kp 22.2
|
||||
// #define DEFAULT_Ki 1.08
|
||||
@ -245,7 +244,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
#define PIDTEMPBED
|
||||
//
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -306,12 +305,6 @@ Here are some standard links for getting your machine calibrated:
|
||||
* The solution: Once the temperature reaches the target, start observing.
|
||||
* If the temperature stays too far below the target (hysteresis) for too long,
|
||||
* the firmware will halt as a safety precaution.
|
||||
*
|
||||
* Note that because the countdown starts only AFTER the temperature reaches
|
||||
* the target, this will not catch a thermistor that is already disconnected
|
||||
* when the print starts!
|
||||
*
|
||||
* To enable for all extruder heaters, uncomment the two defines below:
|
||||
*/
|
||||
|
||||
#define THERMAL_RUNAWAY_PROTECTION_HOTENDS // Enable thermal protection for all extruders
|
||||
@ -342,6 +335,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
#define DELTA
|
||||
|
||||
#ifdef DELTA
|
||||
|
||||
// Make delta curves from many straight lines (linear interpolation).
|
||||
// This is a trade-off between visible corners (not enough segments)
|
||||
// and processor overload (too many expensive sqrt calls).
|
||||
@ -494,7 +488,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
// @section bedlevel
|
||||
|
||||
#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
|
||||
// /// #define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||
// #define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
@ -538,7 +532,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
// Works best with ACCURATE_BED_LEVELING_POINTS 5 or higher.
|
||||
#define NONLINEAR_BED_LEVELING
|
||||
|
||||
#else // not AUTO_BED_LEVELING_GRID
|
||||
#else // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
// Arbitrary points to probe. A simple cross-product
|
||||
// is used to estimate the plane of the bed.
|
||||
@ -574,10 +568,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
|
||||
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||
|
||||
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
|
||||
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
|
||||
// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
|
||||
|
||||
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
|
||||
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
||||
#define Z_PROBE_ALLEN_KEY
|
||||
@ -586,8 +576,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
// 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
|
||||
// if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
|
||||
|
||||
// Allen key retractable z-probe as seen on many Kossel delta printers - http://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
|
||||
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
||||
//#define Z_PROBE_ALLEN_KEY_DEPLOY_1_X 30
|
||||
//#define Z_PROBE_ALLEN_KEY_DEPLOY_1_Y DELTA_PRINTABLE_RADIUS
|
||||
//#define Z_PROBE_ALLEN_KEY_DEPLOY_1_Z 100
|
||||
@ -661,6 +649,10 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE HOMING_FEEDRATE_Z
|
||||
#endif
|
||||
|
||||
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
|
||||
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
|
||||
// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
|
||||
|
||||
// #define PROBE_SERVO_DEACTIVATION_DELAY 300
|
||||
|
||||
|
||||
@ -679,6 +671,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
#define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28)
|
||||
#define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28)
|
||||
|
||||
#endif
|
||||
|
||||
// Support for a dedicated Z PROBE endstop separate from the Z MIN endstop.
|
||||
// If you would like to use both a Z PROBE and a Z MIN endstop together or just a Z PROBE with a custom pin, uncomment #define Z_PROBE_ENDSTOP and read the instructions below.
|
||||
@ -693,7 +686,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
// WARNING: Setting the wrong pin may have unexpected and potentially disastrous outcomes. Use with caution and do your homework.
|
||||
|
||||
//#define Z_PROBE_ENDSTOP
|
||||
#endif // Z_SAFE_HOMING
|
||||
|
||||
#endif // ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
@ -720,7 +712,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
|
||||
////// #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
|
||||
// set the homing speeds (mm/min)
|
||||
// delta homing speeds must be the same on xyz
|
||||
/// delta homing speeds must be the same on xyz
|
||||
#define HOMING_FEEDRATE_X (200*60)
|
||||
#define HOMING_FEEDRATE_Y (200*60)
|
||||
#define HOMING_FEEDRATE_Z (200*60)
|
||||
@ -799,7 +791,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
// @section lcd
|
||||
|
||||
// Define your display language below. Replace (en) with your language code and uncomment.
|
||||
// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test
|
||||
// en, pl, fr, de, es, ru, bg, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test
|
||||
// See also language.h
|
||||
#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
|
||||
@ -1042,7 +1034,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
// Servo Endstops
|
||||
//
|
||||
// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
|
||||
// Use M206 command to correct for switch height offset to actual nozzle height. Store that setting with M500.
|
||||
// Use M851 to set the z-probe vertical offset from the nozzle. Store that setting with M500.
|
||||
//
|
||||
//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
|
||||
//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
|
||||
|
||||
@ -224,7 +224,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
//#define PIDTEMPBED
|
||||
//
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -376,7 +376,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
|
||||
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
#endif
|
||||
//===========================================================================
|
||||
//=========================== Manual Bed Leveling ===========================
|
||||
//===========================================================================
|
||||
|
||||
@ -229,7 +229,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// shouldn't use bed PID until someone else verifies your hardware works.
|
||||
// If this is enabled, find your own PID constants below.
|
||||
//#define PIDTEMPBED
|
||||
//
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
|
||||
@ -377,7 +377,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//=========================== Manual Bed Leveling ===========================
|
||||
|
||||
@ -422,11 +422,11 @@ void checkExtruderAutoFans() {
|
||||
// update extruder auto fan states
|
||||
#if HAS_AUTO_FAN_0
|
||||
setExtruderAutoFanState(EXTRUDER_0_AUTO_FAN_PIN, (fanState & 1) != 0);
|
||||
#endif
|
||||
#endif
|
||||
#if HAS_AUTO_FAN_1
|
||||
if (EXTRUDER_1_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN)
|
||||
setExtruderAutoFanState(EXTRUDER_1_AUTO_FAN_PIN, (fanState & 2) != 0);
|
||||
#endif
|
||||
#endif
|
||||
#if HAS_AUTO_FAN_2
|
||||
if (EXTRUDER_2_AUTO_FAN_PIN != EXTRUDER_0_AUTO_FAN_PIN
|
||||
&& EXTRUDER_2_AUTO_FAN_PIN != EXTRUDER_1_AUTO_FAN_PIN)
|
||||
@ -1238,7 +1238,7 @@ ISR(TIMER0_COMPB_vect) {
|
||||
static unsigned char state_timer_heater_ ## n = 0
|
||||
#else
|
||||
#define ISR_STATICS(n) static unsigned char soft_pwm_ ## n
|
||||
#endif
|
||||
#endif
|
||||
|
||||
// Statics per heater
|
||||
ISR_STATICS(0);
|
||||
|
||||
@ -1665,7 +1665,7 @@ void lcd_reset_alert_level() { lcd_status_message_level = 0; }
|
||||
#define encrot1 2
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Read encoder buttons from the hardware registers
|
||||
|
||||
@ -31,7 +31,7 @@
|
||||
// encoder click is directly connected
|
||||
#define BLEN_C 2
|
||||
#define EN_C BIT(BLEN_C)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//
|
||||
// Setup other button mappings of each panel
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user