Cleanup of temperature code

- Reduce calls to millis()
- General cleanup of manage_heaters
- General cleanup of pid autotune
- Formatting here & there
- Macros to clean up and shrink ISR code (reduced by ~364 lines)

Marlin/pins_RUMBA.h

@@ -6,6 +6,10 @@
   #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
 #endif
 
+#if EXTRUDERS > 3
+  #error RUMBA supports up to 3 extruders. Comment this line to keep going.
+#endif
+
 #define X_STEP_PIN         17
 #define X_DIR_PIN          16
 #define X_ENABLE_PIN       48

Marlin/temperature.h

@@ -85,55 +85,25 @@ extern float current_temperature_bed;
 //inline so that there is no performance decrease.
 //deg=degreeCelsius
 
-FORCE_INLINE float degHotend(uint8_t extruder) {  
-  return current_temperature[extruder];
-};
+FORCE_INLINE float degHotend(uint8_t extruder) { return current_temperature[extruder]; }
+FORCE_INLINE float degBed() { return current_temperature_bed; }
 
 #ifdef SHOW_TEMP_ADC_VALUES
-  FORCE_INLINE float rawHotendTemp(uint8_t extruder) {  
-    return current_temperature_raw[extruder];
-  };
-
-  FORCE_INLINE float rawBedTemp() {  
-    return current_temperature_bed_raw;
-  };
+  FORCE_INLINE float rawHotendTemp(uint8_t extruder) { return current_temperature_raw[extruder]; }
+  FORCE_INLINE float rawBedTemp() { return current_temperature_bed_raw; }
 #endif
 
-FORCE_INLINE float degBed() {
-  return current_temperature_bed;
-};
+FORCE_INLINE float degTargetHotend(uint8_t extruder) { return target_temperature[extruder]; }
+FORCE_INLINE float degTargetBed() { return target_temperature_bed; }
 
-FORCE_INLINE float degTargetHotend(uint8_t extruder) {  
-  return target_temperature[extruder];
-};
+FORCE_INLINE void setTargetHotend(const float &celsius, uint8_t extruder) { target_temperature[extruder] = celsius; }
+FORCE_INLINE void setTargetBed(const float &celsius) { target_temperature_bed = celsius; }
 
-FORCE_INLINE float degTargetBed() {   
-  return target_temperature_bed;
-};
+FORCE_INLINE bool isHeatingHotend(uint8_t extruder) { return target_temperature[extruder] > current_temperature[extruder]; }
+FORCE_INLINE bool isHeatingBed() { return target_temperature_bed > current_temperature_bed; }
 
-FORCE_INLINE void setTargetHotend(const float &celsius, uint8_t extruder) {  
-  target_temperature[extruder] = celsius;
-};
-
-FORCE_INLINE void setTargetBed(const float &celsius) {  
-  target_temperature_bed = celsius;
-};
-
-FORCE_INLINE bool isHeatingHotend(uint8_t extruder){  
-  return target_temperature[extruder] > current_temperature[extruder];
-};
-
-FORCE_INLINE bool isHeatingBed() {
-  return target_temperature_bed > current_temperature_bed;
-};
-
-FORCE_INLINE bool isCoolingHotend(uint8_t extruder) {  
-  return target_temperature[extruder] < current_temperature[extruder];
-};
-
-FORCE_INLINE bool isCoolingBed() {
-  return target_temperature_bed < current_temperature_bed;
-};
+FORCE_INLINE bool isCoolingHotend(uint8_t extruder) { return target_temperature[extruder] < current_temperature[extruder]; }
+FORCE_INLINE bool isCoolingBed() { return target_temperature_bed < current_temperature_bed; }
 
 #define degHotend0() degHotend(0)
 #define degTargetHotend0() degTargetHotend(0)
@@ -171,8 +141,6 @@ FORCE_INLINE bool isCoolingBed() {
   #error Invalid number of extruders
 #endif
 
-
-
 int getHeaterPower(int heater);
 void disable_heater();
 void setWatch();
@@ -191,8 +159,7 @@ static bool thermal_runaway = false;
 
 FORCE_INLINE void autotempShutdown() {
   #ifdef AUTOTEMP
-  if(autotemp_enabled)
-  {
+    if (autotemp_enabled) {
       autotemp_enabled = false;
       if (degTargetHotend(active_extruder) > autotemp_min)
         setTargetHotend(0, active_extruder);