From 9b94210394f8cbc4622c7235bc97d3d351c1908e Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Sat, 15 Apr 2017 01:25:13 -0500 Subject: [PATCH] Bring FLSUN config more up to date --- .../delta/FLSUN/auto_calibrate/Configuration.h | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) diff --git a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h index 7cd28728e1..28217571c8 100644 --- a/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h +++ b/Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h @@ -446,8 +446,6 @@ // and processor overload (too many expensive sqrt calls). #define DELTA_SEGMENTS_PER_SECOND 160 - // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them - // Center-to-center distance of the holes in the diagonal push rods. #define DELTA_DIAGONAL_ROD 218.0 // mm @@ -470,7 +468,6 @@ #define DELTA_PRINTABLE_RADIUS 90.0 // Delta calibration menu - // uncomment to add three points calibration menu option. // See http://minow.blogspot.com/index.html#4918805519571907051 #define DELTA_CALIBRATION_MENU @@ -670,6 +667,9 @@ * is enabled then it also applies to Z_PROBE_SPEED_SLOW. */ +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + // Enable if you have a Z probe mounted on a sled like those designed by Charles Bell. //#define Z_PROBE_SLED //#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. @@ -728,7 +728,7 @@ #define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0 #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS #define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0 - #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_SPEED/10) + #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_SPEED)/10 #define Z_PROBE_ALLEN_KEY_DEPLOY_3_X Z_PROBE_ALLEN_KEY_DEPLOY_2_X * 0.75 #define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y Z_PROBE_ALLEN_KEY_DEPLOY_2_Y * 0.75 @@ -864,11 +864,11 @@ // @section machine // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. -#define INVERT_X_DIR true // DELTA does not invert +#define INVERT_X_DIR true #define INVERT_Y_DIR true #define INVERT_Z_DIR true -// Enable this option for Toshiba steppers +// Enable this option for Toshiba stepper drivers //#define CONFIG_STEPPERS_TOSHIBA // @section extruder @@ -987,6 +987,7 @@ #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR) // Set the number of grid points per dimension. + // Works best with 5 or more points in each dimension. #define GRID_MAX_POINTS_X 9 #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X @@ -1004,7 +1005,6 @@ //#define PROBE_Y_FIRST #if ENABLED(AUTO_BED_LEVELING_BILINEAR) - // // Experimental Subdivision of the grid by Catmull-Rom method. // Synthesizes intermediate points to produce a more detailed mesh.