🧻 Cosmetic changes (#20859)

Marlin/Configuration.h

@@ -421,7 +421,7 @@
 #define TEMP_SENSOR_CHAMBER 0
 
 // Dummy thermistor constant temperature readings, for use with 998 and 999
-#define DUMMY_THERMISTOR_998_VALUE 25
+#define DUMMY_THERMISTOR_998_VALUE  25
 #define DUMMY_THERMISTOR_999_VALUE 100
 
 // Resistor values when using MAX31865 sensors (-5) on TEMP_SENSOR_0 / 1
@@ -1360,7 +1360,7 @@
     #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for the G26 Mesh Validation Tool.
     #define MESH_TEST_HOTEND_TEMP  205    // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
     #define MESH_TEST_BED_TEMP      60    // (°C) Default bed temperature for the G26 Mesh Validation Tool.
-    #define G26_XY_FEEDRATE         20    // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool.
+    #define G26_XY_FEEDRATE        100    // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool.
     #define G26_RETRACT_MULTIPLIER   1.0  // G26 Q (retraction) used by default between mesh test elements.
   #endif
 

Marlin/Configuration_adv.h

@@ -163,7 +163,7 @@
   #if ENABLED(CHAMBER_VENT)
     #define CHAMBER_VENT_SERVO_NR  1  // Index of the vent servo
     #define HIGH_EXCESS_HEAT_LIMIT 5  // How much above target temp to consider there is excess heat in the chamber
-    #define LOW_EXCESS_HEAT_LIMIT 3
+    #define LOW_EXCESS_HEAT_LIMIT  3
     #define MIN_COOLING_SLOPE_TIME_CHAMBER_VENT 20
     #define MIN_COOLING_SLOPE_DEG_CHAMBER_VENT 1.5
   #endif
@@ -206,7 +206,7 @@
    * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
    * below 2.
    */
-  #define WATCH_TEMP_PERIOD 20                // Seconds
+  #define WATCH_TEMP_PERIOD  20               // Seconds
   #define WATCH_TEMP_INCREASE 2               // Degrees Celsius
 #endif
 
@@ -284,8 +284,8 @@
       // DEFAULT_Kf and PID_FAN_SCALING_LIN_FACTOR are calculated accordingly.
 
       #define PID_FAN_SCALING_AT_FULL_SPEED 13.0        //=PID_FAN_SCALING_LIN_FACTOR*255+DEFAULT_Kf
-      #define PID_FAN_SCALING_AT_MIN_SPEED 6.0          //=PID_FAN_SCALING_LIN_FACTOR*PID_FAN_SCALING_MIN_SPEED+DEFAULT_Kf
-      #define PID_FAN_SCALING_MIN_SPEED 10.0            // Minimum fan speed at which to enable PID_FAN_SCALING
+      #define PID_FAN_SCALING_AT_MIN_SPEED   6.0        //=PID_FAN_SCALING_LIN_FACTOR*PID_FAN_SCALING_MIN_SPEED+DEFAULT_Kf
+      #define PID_FAN_SCALING_MIN_SPEED     10.0        // Minimum fan speed at which to enable PID_FAN_SCALING
 
       #define DEFAULT_Kf (255.0*PID_FAN_SCALING_AT_MIN_SPEED-PID_FAN_SCALING_AT_FULL_SPEED*PID_FAN_SCALING_MIN_SPEED)/(255.0-PID_FAN_SCALING_MIN_SPEED)
       #define PID_FAN_SCALING_LIN_FACTOR (PID_FAN_SCALING_AT_FULL_SPEED-DEFAULT_Kf)/255.0
@@ -2056,21 +2056,21 @@
  */
 //#define FWRETRACT
 #if ENABLED(FWRETRACT)
-  #define FWRETRACT_AUTORETRACT           // Override slicer retractions
+  #define FWRETRACT_AUTORETRACT             // Override slicer retractions
   #if ENABLED(FWRETRACT_AUTORETRACT)
-    #define MIN_AUTORETRACT 0.1           // (mm) Don't convert E moves under this length
-    #define MAX_AUTORETRACT 10.0          // (mm) Don't convert E moves over this length
+    #define MIN_AUTORETRACT             0.1 // (mm) Don't convert E moves under this length
+    #define MAX_AUTORETRACT            10.0 // (mm) Don't convert E moves over this length
   #endif
-  #define RETRACT_LENGTH 3                // (mm) Default retract length (positive value)
-  #define RETRACT_LENGTH_SWAP 13          // (mm) Default swap retract length (positive value)
-  #define RETRACT_FEEDRATE 45             // (mm/s) Default feedrate for retracting
-  #define RETRACT_ZRAISE 0                // (mm) Default retract Z-raise
-  #define RETRACT_RECOVER_LENGTH 0        // (mm) Default additional recover length (added to retract length on recover)
-  #define RETRACT_RECOVER_LENGTH_SWAP 0   // (mm) Default additional swap recover length (added to retract length on recover from toolchange)
-  #define RETRACT_RECOVER_FEEDRATE 8      // (mm/s) Default feedrate for recovering from retraction
-  #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // (mm/s) Default feedrate for recovering from swap retraction
+  #define RETRACT_LENGTH                3   // (mm) Default retract length (positive value)
+  #define RETRACT_LENGTH_SWAP          13   // (mm) Default swap retract length (positive value)
+  #define RETRACT_FEEDRATE             45   // (mm/s) Default feedrate for retracting
+  #define RETRACT_ZRAISE                0   // (mm) Default retract Z-raise
+  #define RETRACT_RECOVER_LENGTH        0   // (mm) Default additional recover length (added to retract length on recover)
+  #define RETRACT_RECOVER_LENGTH_SWAP   0   // (mm) Default additional swap recover length (added to retract length on recover from toolchange)
+  #define RETRACT_RECOVER_FEEDRATE      8   // (mm/s) Default feedrate for recovering from retraction
+  #define RETRACT_RECOVER_FEEDRATE_SWAP 8   // (mm/s) Default feedrate for recovering from swap retraction
   #if ENABLED(MIXING_EXTRUDER)
-    //#define RETRACT_SYNC_MIXING         // Retract and restore all mixing steppers simultaneously
+    //#define RETRACT_SYNC_MIXING           // Retract and restore all mixing steppers simultaneously
   #endif
 #endif