melch/Marlin
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity

✨ "Rutilea" ESP32 board (#22880)

Browse Source
This commit is contained in:
Scott Lahteine 2021-10-29 20:46:55 -05:00
parent 6f59d8171f
commit 8562f0ec44
8 changed files with 148 additions and 128 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

18
Marlin/src/HAL/ESP32/i2s.cpp
View File

@ -64,13 +64,10 @@ uint32_t i2s_port_data = 0;
#define I2S_EXIT_CRITICAL() portEXIT_CRITICAL(&i2s_spinlock[i2s_num])
static inline void gpio_matrix_out_check(uint32_t gpio, uint32_t signal_idx, bool out_inv, bool oen_inv) {
//if pin = -1, do not need to configure
if (gpio != -1) {
PIN_FUNC_SELECT(GPIO_PIN_MUX_REG[gpio], PIN_FUNC_GPIO);
gpio_set_direction((gpio_num_t)gpio, (gpio_mode_t)GPIO_MODE_DEF_OUTPUT);
gpio_matrix_out(gpio, signal_idx, out_inv, oen_inv);
}
}
static esp_err_t i2s_reset_fifo(i2s_port_t i2s_num) {
I2S_ENTER_CRITICAL();
@ -256,13 +253,7 @@ int i2s_init() {
I2S0.fifo_conf.dscr_en = 0;
I2S0.conf_chan.tx_chan_mod = (
#if ENABLED(I2S_STEPPER_SPLIT_STREAM)
4
#else
0
#endif
);
I2S0.conf_chan.tx_chan_mod = TERN(I2S_STEPPER_SPLIT_STREAM, 4, 0);
I2S0.fifo_conf.tx_fifo_mod = 0;
I2S0.conf.tx_mono = 0;
@ -313,9 +304,16 @@ int i2s_init() {
xTaskCreatePinnedToCore(stepperTask, "StepperTask", 10000, nullptr, 1, nullptr, CONFIG_ARDUINO_RUNNING_CORE); // run I2S stepper task on same core as rest of Marlin
// Route the i2s pins to the appropriate GPIO
// If a pin is not defined, no need to configure
#if defined(I2S_DATA) && I2S_DATA >= 0
gpio_matrix_out_check(I2S_DATA, I2S0O_DATA_OUT23_IDX, 0, 0);
#endif
#if defined(I2S_BCK) && I2S_BCK >= 0
gpio_matrix_out_check(I2S_BCK, I2S0O_BCK_OUT_IDX, 0, 0);
#endif
#if defined(I2S_WS) && I2S_WS >= 0
gpio_matrix_out_check(I2S_WS, I2S0O_WS_OUT_IDX, 0, 0);
#endif
// Start the I2S peripheral
return i2s_start(I2S_NUM_0);

7
Marlin/src/core/boards.h
View File

@ -425,9 +425,10 @@
#define BOARD_MRR_ESPA 6001 // MRR ESPA based on ESP32 (native pins only)
#define BOARD_MRR_ESPE 6002 // MRR ESPE based on ESP32 (with I2S stepper stream)
#define BOARD_E4D_BOX 6003 // E4d@BOX
#define BOARD_FYSETC_E4 6004 // FYSETC E4
#define BOARD_PANDA_ZHU 6005 // Panda_ZHU
#define BOARD_PANDA_M4 6006 // Panda_M4
#define BOARD_RESP32_CUSTOM 6004 // Rutilea ESP32 custom board
#define BOARD_FYSETC_E4 6005 // FYSETC E4
#define BOARD_PANDA_ZHU 6006 // Panda_ZHU
#define BOARD_PANDA_M4 6007 // Panda_M4
//
// SAMD51 ARM Cortex M4

89
Marlin/src/pins/esp32/pins_ESPA_common.h Normal file
View File

@ -0,0 +1,89 @@
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
#pragma once
/**
* ESPA-like pin assignments
* Supports 4 stepper drivers, heated bed, single hotend.
*/
#include "env_validate.h"
#ifndef DEFAULT_MACHINE_NAME
#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
#endif
//
// Disable I2S stepper stream, by default
//
#undef I2S_STEPPER_STREAM
#undef I2S_WS
#undef I2S_BCK
#undef I2S_DATA
//
// Limit Switches
//
#define X_STOP_PIN 34
#define Y_STOP_PIN 35
#define Z_STOP_PIN 15
//
// Steppers
//
#define X_STEP_PIN 27
#define X_DIR_PIN 26
#define X_ENABLE_PIN 25
#define Y_STEP_PIN 33
#define Y_DIR_PIN 32
#define Y_ENABLE_PIN X_ENABLE_PIN
#define Z_STEP_PIN 14
#define Z_DIR_PIN 12
#define Z_ENABLE_PIN X_ENABLE_PIN
#define E0_STEP_PIN 16
#define E0_DIR_PIN 17
#define E0_ENABLE_PIN X_ENABLE_PIN
//
// Temperature Sensors
//
#define TEMP_0_PIN 36 // Analog Input
#define TEMP_BED_PIN 39 // Analog Input
//
// Heaters / Fans
//
#define HEATER_0_PIN 2
#define FAN_PIN 13
#define HEATER_BED_PIN 4
//
// MicroSD card
//
#define SD_MOSI_PIN 23
#define SD_MISO_PIN 19
#define SD_SCK_PIN 18
#define SDSS 5
#define USES_SHARED_SPI // SPI is shared by SD card with TMC SPI drivers

57
Marlin/src/pins/esp32/pins_FYSETC_E4.h
View File

@ -37,41 +37,8 @@
#endif
#define BOARD_INFO_NAME "FYSETC_E4"
#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
//
// Disable I2S stepper stream
//
#undef I2S_STEPPER_STREAM
#define I2S_WS -1
#define I2S_BCK -1
#define I2S_DATA -1
//
// Limit Switches
//
#define X_STOP_PIN 34
#define Y_STOP_PIN 35
#define Z_STOP_PIN 15
//
// Steppers
//
#define X_STEP_PIN 27
#define X_DIR_PIN 26
#define X_ENABLE_PIN 25
#define Y_STEP_PIN 33
#define Y_DIR_PIN 32
#define Y_ENABLE_PIN X_ENABLE_PIN
#define Z_STEP_PIN 14
#define Z_DIR_PIN 12
#define Z_ENABLE_PIN X_ENABLE_PIN
#define E0_STEP_PIN 16
#define E0_DIR_PIN 17
#define E0_ENABLE_PIN X_ENABLE_PIN
#include "pins_ESPA_common.h"
#if HAS_TMC_UART
//
@ -89,28 +56,6 @@
#define TMC_BAUD_RATE 115200
#endif
//
// Temperature Sensors
//
#define TEMP_0_PIN 36 // Analog Input
#define TEMP_BED_PIN 39 // Analog Input
//
// Heaters / Fans
//
#define HEATER_0_PIN 2
#define FAN_PIN 13
#define HEATER_BED_PIN 4
//
// MicroSD card
//
#define SD_MOSI_PIN 23
#define SD_MISO_PIN 19
#define SD_SCK_PIN 18
#define SDSS 5
#define USES_SHARED_SPI // SPI is shared by SD card with TMC SPI drivers
/**
* Hardware serial pins
*

53
Marlin/src/pins/esp32/pins_MRR_ESPA.h
View File

@ -38,68 +38,17 @@
#define BOARD_INFO_NAME "MRR ESPA"
#define BOARD_WEBSITE_URL "github.com/maplerainresearch/MRR_ESPA"
#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
//
// Disable I2S stepper stream
//
#undef I2S_STEPPER_STREAM
#undef I2S_WS
#undef I2S_BCK
#undef I2S_DATA
//
// Limit Switches
//
#define X_STOP_PIN 34
#define Y_STOP_PIN 35
#define Z_STOP_PIN 15
#include "pins_ESPA_common.h"
//
// Steppers
//
#define X_STEP_PIN 27
#define X_DIR_PIN 26
#define X_ENABLE_PIN 25
//#define X_CS_PIN 21
#define Y_STEP_PIN 33
#define Y_DIR_PIN 32
#define Y_ENABLE_PIN X_ENABLE_PIN
//#define Y_CS_PIN 22
#define Z_STEP_PIN 14
#define Z_DIR_PIN 12
#define Z_ENABLE_PIN X_ENABLE_PIN
//#define Z_CS_PIN 5 // SS_PIN
#define E0_STEP_PIN 16
#define E0_DIR_PIN 17
#define E0_ENABLE_PIN X_ENABLE_PIN
//#define E0_CS_PIN 21
//
// Temperature Sensors
//
#define TEMP_0_PIN 36 // Analog Input
#define TEMP_BED_PIN 39 // Analog Input
//
// Heaters / Fans
//
#define HEATER_0_PIN 2
#define FAN_PIN 13
#define HEATER_BED_PIN 4
//
// MicroSD card
//
#define SD_MOSI_PIN 23
#define SD_MISO_PIN 19
#define SD_SCK_PIN 18
#define SDSS 5
#define USES_SHARED_SPI // SPI is shared by SD card with TMC SPI drivers
// Hardware serial pins
// Add the following to Configuration.h or Configuration_adv.h to assign
// specific pins to hardware Serial1.

1
Marlin/src/pins/esp32/pins_MRR_ESPE.h
View File

@ -51,7 +51,6 @@
//
// Enable I2S stepper stream
//
#undef I2S_STEPPER_STREAM
#define I2S_STEPPER_STREAM
#define I2S_WS 26
#define I2S_BCK 25

37
Marlin/src/pins/esp32/pins_RESP32_CUSTOM.h Normal file
View File

@ -0,0 +1,37 @@
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
#pragma once
/**
* Rutilea ESP32 (Tensilica Xtensa LX6) pin assignments
*/
#include "env_validate.h"
#define BOARD_INFO_NAME "Rutilea ESP32"
#include "pins_ESPA_common.h"
//
// I2S (steppers & other output-only pins)
//
#define I2S_STEPPER_STREAM

2
Marlin/src/pins/pins.h
View File

@ -695,6 +695,8 @@
#include "esp32/pins_MRR_ESPE.h" // ESP32 env:esp32
#elif MB(E4D_BOX)
#include "esp32/pins_E4D.h" // ESP32 env:esp32
#elif MB(RESP32_CUSTOM)
#include "esp32/pins_RESP32_CUSTOM.h" // ESP32 env:esp32
#elif MB(FYSETC_E4)
#include "esp32/pins_FYSETC_E4.h" // ESP32 env:FYSETC_E4
#elif MB(PANDA_ZHU)