diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index eb3a22fc31..5faed3c8b9 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 3763ec1724..e36bfa895e 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h
index b1e53c608a..a4789f7d97 100644
--- a/Marlin/src/inc/Conditionals_post.h
+++ b/Marlin/src/inc/Conditionals_post.h
@@ -918,7 +918,7 @@
#define HAS_TEMP_HOTEND (HAS_TEMP_ADC_0 || ENABLED(HEATER_0_USES_MAX6675))
#define HAS_TEMP_BED HAS_TEMP_ADC_BED
#define HAS_TEMP_CHAMBER HAS_TEMP_ADC_CHAMBER
-#define HAS_HEATED_CHAMBER (HAS_TEMP_CHAMBER && PIN_EXISTS(CHAMBER_HEATER))
+#define HAS_HEATED_CHAMBER (HAS_TEMP_CHAMBER && PIN_EXISTS(HEATER_CHAMBER))
// Heaters
#define HAS_HEATER_0 (PIN_EXISTS(HEATER_0))
diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h
index a927900557..d76c28bbf2 100644
--- a/Marlin/src/inc/SanityCheck.h
+++ b/Marlin/src/inc/SanityCheck.h
@@ -343,6 +343,8 @@
#error "MAX6675_SS2 is now MAX6675_SS2_PIN. Please update your configuration and/or pins."
#elif defined(SPINDLE_LASER_ENABLE_PIN)
#error "SPINDLE_LASER_ENABLE_PIN is now SPINDLE_LASER_ENA_PIN. Please update your configuration and/or pins."
+#elif defined(CHAMBER_HEATER_PIN)
+ #error "CHAMBER_HEATER_PIN is now HEATER_CHAMBER_PIN. Please update your configuration and/or pins."
#elif defined(TMC_Z_CALIBRATION)
#error "TMC_Z_CALIBRATION has been deprecated in favor of Z_STEPPER_AUTO_ALIGN. Please update your configuration."
#elif defined(Z_MIN_PROBE_ENDSTOP)
diff --git a/Marlin/src/module/temperature.cpp b/Marlin/src/module/temperature.cpp
index d8bf25747e..8f3361944d 100644
--- a/Marlin/src/module/temperature.cpp
+++ b/Marlin/src/module/temperature.cpp
@@ -595,10 +595,23 @@ temp_range_t Temperature::temp_range[HOTENDS] = ARRAY_BY_HOTENDS(sensor_heater_0
Temperature::Temperature() { }
-int Temperature::getHeaterPower(const int heater) {
+int16_t Temperature::getHeaterPower(const int8_t heater) {
return (
+ #if HAS_HEATED_CHAMBER
+ #if HAS_HEATED_BED
+ heater == -2
+ #else
+ heater < 0
+ #endif
+ ? temp_chamber.soft_pwm_amount :
+ #endif
#if HAS_HEATED_BED
- heater < 0 ? temp_bed.soft_pwm_amount :
+ #if HAS_HEATED_CHAMBER
+ heater == -1
+ #else
+ heater < 0
+ #endif
+ ? temp_bed.soft_pwm_amount :
#endif
temp_hotend[heater].soft_pwm_amount
);
@@ -1073,11 +1086,11 @@ void Temperature::manage_heater() {
if (WITHIN(temp_chamber.current, CHAMBER_MINTEMP, CHAMBER_MAXTEMP)) {
#if ENABLED(CHAMBER_LIMIT_SWITCHING)
- if (temp_chamber.current >= temp_chamber.target + CHAMBER_HYSTERESIS)
+ if (temp_chamber.current >= temp_chamber.target + TEMP_CHAMBER_HYSTERESIS)
temp_chamber.soft_pwm_amount = 0;
- else if (temp_chamber.current <= temp_chamber.target - (CHAMBER_HYSTERESIS))
+ else if (temp_chamber.current <= temp_chamber.target - (TEMP_CHAMBER_HYSTERESIS))
temp_chamber.soft_pwm_amount = MAX_CHAMBER_POWER >> 1;
- #else // !PIDTEMPCHAMBER && !CHAMBER_LIMIT_SWITCHING
+ #else
temp_chamber.soft_pwm_amount = temp_chamber.current < temp_chamber.target ? MAX_CHAMBER_POWER >> 1 : 0;
#endif
}
@@ -2017,11 +2030,7 @@ void Temperature::readings_ready() {
#else
#define CHAMBERCMP(A,B) ((A)>=(B))
#endif
- const bool chamber_on = (temp_chamber.target > 0)
- #if ENABLED(PIDTEMPCHAMBER)
- || (temp_chamber.soft_pwm_amount > 0)
- #endif
- ;
+ const bool chamber_on = (temp_chamber.target > 0);
if (CHAMBERCMP(temp_chamber.raw, maxtemp_raw_CHAMBER)) max_temp_error(-2);
if (chamber_on && CHAMBERCMP(mintemp_raw_CHAMBER, temp_chamber.raw)) min_temp_error(-2);
#endif
@@ -2602,11 +2611,12 @@ void Temperature::isr() {
, e
);
#endif
- SERIAL_ECHOPGM(" @:");
- SERIAL_ECHO(getHeaterPower(target_extruder));
+ SERIAL_ECHOPAIR(" @:", getHeaterPower(target_extruder));
#if HAS_HEATED_BED
- SERIAL_ECHOPGM(" B@:");
- SERIAL_ECHO(getHeaterPower(-1));
+ SERIAL_ECHOPAIR(" B@:", getHeaterPower(-1));
+ #endif
+ #if HAS_HEATED_CHAMBER
+ SERIAL_ECHOPAIR(" C@:", getHeaterPower(-2));
#endif
#if HOTENDS > 1
HOTEND_LOOP() {
diff --git a/Marlin/src/module/temperature.h b/Marlin/src/module/temperature.h
index a8cfad34b3..b24f84fb58 100644
--- a/Marlin/src/module/temperature.h
+++ b/Marlin/src/module/temperature.h
@@ -206,16 +206,10 @@ struct PIDHeaterInfo : public HeaterInfo {
typedef heater_info_t bed_info_t;
#endif
#endif
-#if HAS_TEMP_CHAMBER
- #if HAS_HEATED_CHAMBER
- #if ENABLED(PIDTEMPCHAMBER)
- typedef struct PIDHeaterInfo<PID_t> chamber_info_t;
- #else
- typedef heater_info_t chamber_info_t;
- #endif
- #else
- typedef temp_info_t chamber_info_t;
- #endif
+#if HAS_HEATED_CHAMBER
+ typedef heater_info_t chamber_info_t;
+#elif HAS_TEMP_CHAMBER
+ typedef temp_info_t chamber_info_t;
#endif
// Heater idle handling
@@ -339,9 +333,7 @@ class Temperature {
#if WATCH_CHAMBER
static heater_watch_t watch_chamber;
#endif
- #if DISABLED(PIDTEMPCHAMBER)
- static millis_t next_chamber_check_ms;
- #endif
+ static millis_t next_chamber_check_ms;
#ifdef CHAMBER_MINTEMP
static int16_t mintemp_raw_CHAMBER;
#endif
@@ -653,7 +645,7 @@ class Temperature {
/**
* The software PWM power for a heater
*/
- static int getHeaterPower(const int heater);
+ static int16_t getHeaterPower(const int8_t heater);
/**
* Switch off all heaters, set all target temperatures to 0
diff --git a/buildroot/share/tests/megaatmega2560-tests b/buildroot/share/tests/megaatmega2560-tests
index e207f3cd74..0ca2c419b7 100755
--- a/buildroot/share/tests/megaatmega2560-tests
+++ b/buildroot/share/tests/megaatmega2560-tests
@@ -42,7 +42,7 @@ opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING EEPROM_SETTINGS \
MAX7219_DEBUG LED_CONTROL_MENU CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CODEPENDENT_XY_HOMING BACKLASH_COMPENSATION BACKLASH_GCODE
opt_enable SLOW_PWM_HEATERS THERMAL_PROTECTION_CHAMBER
opt_set TEMP_SENSOR_CHAMBER 3
-opt_set CHAMBER_HEATER_PIN 45
+opt_set HEATER_CHAMBER_PIN 45
exec_test $1 $2 "RAMPS with 2 extruders, RRDFGSC, Linear ABL, LEDs, and many options"
#
diff --git a/config/default/Configuration.h b/config/default/Configuration.h
index eb3a22fc31..5faed3c8b9 100644
--- a/config/default/Configuration.h
+++ b/config/default/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h
index 42f7dc3f58..46c2554eb6 100644
--- a/config/default/Configuration_adv.h
+++ b/config/default/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h
index 93cefc58a7..143622824d 100644
--- a/config/examples/3DFabXYZ/Migbot/Configuration.h
+++ b/config/examples/3DFabXYZ/Migbot/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -481,7 +476,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
index 994643c591..ba21fd3d20 100644
--- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
+++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/AlephObjects/TAZ4/Configuration.h b/config/examples/AlephObjects/TAZ4/Configuration.h
index 1fd4ad8536..0720c14f0b 100644
--- a/config/examples/AlephObjects/TAZ4/Configuration.h
+++ b/config/examples/AlephObjects/TAZ4/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 7
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 250
#define HEATER_5_MAXTEMP 250
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -485,7 +480,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
index 740db482ea..eebde4ff3d 100644
--- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h
index f9e6beeb5d..916bb06854 100644
--- a/config/examples/AliExpress/CL-260/Configuration.h
+++ b/config/examples/AliExpress/CL-260/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h
index dbeb0f0da5..e904da3019 100644
--- a/config/examples/AliExpress/UM2pExt/Configuration.h
+++ b/config/examples/AliExpress/UM2pExt/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 20
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 130
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -487,7 +482,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
index c4e72a91aa..df3b97b2d8 100644
--- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h
+++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h
index 7c395945ac..669dee2af0 100644
--- a/config/examples/Anet/A2/Configuration.h
+++ b/config/examples/Anet/A2/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h
index f0bd8e9795..95c43b74ae 100644
--- a/config/examples/Anet/A2/Configuration_adv.h
+++ b/config/examples/Anet/A2/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h
index 06d8906b2a..325939564e 100644
--- a/config/examples/Anet/A2plus/Configuration.h
+++ b/config/examples/Anet/A2plus/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h
index f0bd8e9795..95c43b74ae 100644
--- a/config/examples/Anet/A2plus/Configuration_adv.h
+++ b/config/examples/Anet/A2plus/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h
index f1a8036da4..64431b72f4 100644
--- a/config/examples/Anet/A6/Configuration.h
+++ b/config/examples/Anet/A6/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 11
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 130
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -487,7 +482,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h
index 0163ffff56..c329a3600a 100644
--- a/config/examples/Anet/A6/Configuration_adv.h
+++ b/config/examples/Anet/A6/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h
index db3c843483..e60533d09d 100644
--- a/config/examples/Anet/A8/Configuration.h
+++ b/config/examples/Anet/A8/Configuration.h
@@ -392,7 +392,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -411,8 +410,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -422,7 +419,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -434,7 +430,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 130
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -483,7 +478,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h
index 52c16e8942..da07576626 100644
--- a/config/examples/Anet/A8/Configuration_adv.h
+++ b/config/examples/Anet/A8/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h
index d4ae37aa46..3da19a382f 100644
--- a/config/examples/AnyCubic/i3/Configuration.h
+++ b/config/examples/AnyCubic/i3/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -481,7 +476,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h
index 51f84d4f87..675ddd5d46 100644
--- a/config/examples/AnyCubic/i3/Configuration_adv.h
+++ b/config/examples/AnyCubic/i3/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h
index 8693153728..d658278ec3 100644
--- a/config/examples/ArmEd/Configuration.h
+++ b/config/examples/ArmEd/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 13
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h
index 5c678649b0..7f73a21bce 100644
--- a/config/examples/ArmEd/Configuration_adv.h
+++ b/config/examples/ArmEd/Configuration_adv.h
@@ -54,6 +54,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -131,8 +144,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h
index 52326ddcff..e8ce57851e 100644
--- a/config/examples/Azteeg/X5GT/Configuration.h
+++ b/config/examples/Azteeg/X5GT/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h
index 6e33f71092..1c0112e329 100644
--- a/config/examples/BIBO/TouchX/cyclops/Configuration.h
+++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 115
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
index 67c84bebf9..96262317b7 100644
--- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h
index 193d5e8b92..ba9b968114 100644
--- a/config/examples/BIBO/TouchX/default/Configuration.h
+++ b/config/examples/BIBO/TouchX/default/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 60
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 115
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h
index 7cd8a52b48..f6b4ae290b 100644
--- a/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h
index bbbfa36a8f..efe46bd7f9 100644
--- a/config/examples/BQ/Hephestos/Configuration.h
+++ b/config/examples/BQ/Hephestos/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 260
#define HEATER_5_MAXTEMP 260
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -464,7 +459,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h
index 01bb63e2b8..8dc95c14ac 100644
--- a/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/config/examples/BQ/Hephestos/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h
index b6ea2e22de..97b8dba743 100644
--- a/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/config/examples/BQ/Hephestos_2/Configuration.h
@@ -399,7 +399,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -418,8 +417,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -429,7 +426,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -441,7 +437,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 100
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -477,7 +472,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h
index e37097f3cc..3502efcc17 100644
--- a/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h
index 5f1429be14..3002eebcec 100644
--- a/config/examples/BQ/WITBOX/Configuration.h
+++ b/config/examples/BQ/WITBOX/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 260
#define HEATER_5_MAXTEMP 260
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -464,7 +459,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h
index 01bb63e2b8..8dc95c14ac 100644
--- a/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/config/examples/BQ/WITBOX/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h
index 6c95487afd..eba8f376d7 100644
--- a/config/examples/Cartesio/Configuration.h
+++ b/config/examples/Cartesio/Configuration.h
@@ -392,7 +392,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -411,8 +410,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -422,7 +419,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -434,7 +430,6 @@
#define HEATER_4_MAXTEMP 415
#define HEATER_5_MAXTEMP 415
#define BED_MAXTEMP 165
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -477,7 +472,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h
index 461fc07c1c..86207af419 100644
--- a/config/examples/Cartesio/Configuration_adv.h
+++ b/config/examples/Cartesio/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Creality/CR-10/Configuration.h b/config/examples/Creality/CR-10/Configuration.h
index 1b8e8c630a..09130f330d 100644
--- a/config/examples/Creality/CR-10/Configuration.h
+++ b/config/examples/Creality/CR-10/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -481,7 +476,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h
index bab024defc..235b59ef74 100644
--- a/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/config/examples/Creality/CR-10/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Creality/CR-10S/Configuration.h b/config/examples/Creality/CR-10S/Configuration.h
index b545a1ac68..8efdab2609 100644
--- a/config/examples/Creality/CR-10S/Configuration.h
+++ b/config/examples/Creality/CR-10S/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h
index e95ed27b5b..4a52d57caf 100644
--- a/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/config/examples/Creality/CR-10S/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Creality/CR-10_5S/Configuration.h b/config/examples/Creality/CR-10_5S/Configuration.h
index 3625b66d9a..eecd2a0ca7 100644
--- a/config/examples/Creality/CR-10_5S/Configuration.h
+++ b/config/examples/Creality/CR-10_5S/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h
index 6110475398..3103766377 100644
--- a/config/examples/Creality/CR-10_5S/Configuration_adv.h
+++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Creality/CR-10mini/Configuration.h b/config/examples/Creality/CR-10mini/Configuration.h
index 7f80fe3746..df9c556bce 100644
--- a/config/examples/Creality/CR-10mini/Configuration.h
+++ b/config/examples/Creality/CR-10mini/Configuration.h
@@ -400,7 +400,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -419,8 +418,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -430,7 +427,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -442,7 +438,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -490,7 +485,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Creality/CR-10mini/Configuration_adv.h b/config/examples/Creality/CR-10mini/Configuration_adv.h
index e2b91c1254..2f1e01aeaa 100644
--- a/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/config/examples/Creality/CR-10mini/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h
index 1324c7767a..3893c0fb9f 100644
--- a/config/examples/Creality/CR-8/Configuration.h
+++ b/config/examples/Creality/CR-8/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -481,7 +476,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h
index 0cdbd719b0..01fb18ad93 100644
--- a/config/examples/Creality/CR-8/Configuration_adv.h
+++ b/config/examples/Creality/CR-8/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h
index 016a666fad..f693b831a5 100644
--- a/config/examples/Creality/Ender-2/Configuration.h
+++ b/config/examples/Creality/Ender-2/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 75
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -480,7 +475,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h
index 6d9ed0020b..6d4555b67c 100644
--- a/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/config/examples/Creality/Ender-2/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Creality/Ender-3/Configuration.h b/config/examples/Creality/Ender-3/Configuration.h
index 0b7f371872..201eb25105 100644
--- a/config/examples/Creality/Ender-3/Configuration.h
+++ b/config/examples/Creality/Ender-3/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 125
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -480,7 +475,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Creality/Ender-3/Configuration_adv.h b/config/examples/Creality/Ender-3/Configuration_adv.h
index b6d54b935b..7d5da09c9b 100644
--- a/config/examples/Creality/Ender-3/Configuration_adv.h
+++ b/config/examples/Creality/Ender-3/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h
index c6dd831476..669203ec4b 100644
--- a/config/examples/Creality/Ender-4/Configuration.h
+++ b/config/examples/Creality/Ender-4/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -481,7 +476,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h
index 7f223f69d6..a7f9a1c6b4 100644
--- a/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/config/examples/Creality/Ender-4/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h
index 583cc7f6db..691b1851a1 100644
--- a/config/examples/Einstart-S/Configuration.h
+++ b/config/examples/Einstart-S/Configuration.h
@@ -393,7 +393,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -412,8 +411,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -423,7 +420,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -435,7 +431,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -484,7 +479,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h
index c67f930f46..9e01b476ad 100644
--- a/config/examples/Einstart-S/Configuration_adv.h
+++ b/config/examples/Einstart-S/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Felix/Configuration.h b/config/examples/Felix/Configuration.h
index e14b9d4dda..b2c5a2ede2 100644
--- a/config/examples/Felix/Configuration.h
+++ b/config/examples/Felix/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -464,7 +459,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Felix/Configuration_adv.h b/config/examples/Felix/Configuration_adv.h
index 26ac45fe55..638aef0b4c 100644
--- a/config/examples/Felix/Configuration_adv.h
+++ b/config/examples/Felix/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h
index ffc8b3c079..4c1d96138b 100644
--- a/config/examples/Felix/DUAL/Configuration.h
+++ b/config/examples/Felix/DUAL/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -464,7 +459,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h
index b8378ef89a..f7e3c71190 100644
--- a/config/examples/FlashForge/CreatorPro/Configuration.h
+++ b/config/examples/FlashForge/CreatorPro/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -466,7 +461,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h
index a31b62d2ee..b7db054010 100644
--- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h
+++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h
index e24f4fbe49..6fb6795d4a 100644
--- a/config/examples/FolgerTech/i3-2020/Configuration.h
+++ b/config/examples/FolgerTech/i3-2020/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 245
#define HEATER_5_MAXTEMP 245
#define BED_MAXTEMP 115
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -481,7 +476,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h
index 0a1c0c42e6..d6a35f40d3 100644
--- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h
index 3ad2975b48..1ca7912ad2 100644
--- a/config/examples/Formbot/Raptor/Configuration.h
+++ b/config/examples/Formbot/Raptor/Configuration.h
@@ -436,7 +436,6 @@
#define TEMP_SENSOR_BED 1
#endif
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -455,8 +454,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -465,7 +462,6 @@
#define HEATER_3_MINTEMP 5
#define HEATER_4_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -480,7 +476,6 @@
#else
#define BED_MAXTEMP 100
#endif
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -528,7 +523,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h
index 4b0080929d..99fc0f5ee0 100644
--- a/config/examples/Formbot/Raptor/Configuration_adv.h
+++ b/config/examples/Formbot/Raptor/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h
index d406ae3bdf..864592dfe1 100644
--- a/config/examples/Formbot/T_Rex_2+/Configuration.h
+++ b/config/examples/Formbot/T_Rex_2+/Configuration.h
@@ -406,7 +406,6 @@
#endif
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -425,8 +424,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -436,7 +433,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -448,7 +444,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -498,7 +493,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
index ef32fde570..da1722d84b 100644
--- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h
index 0b5e80d7d4..4ab2609e16 100644
--- a/config/examples/Formbot/T_Rex_3/Configuration.h
+++ b/config/examples/Formbot/T_Rex_3/Configuration.h
@@ -400,7 +400,6 @@
#endif
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -419,8 +418,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -430,7 +427,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -442,7 +438,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -485,7 +480,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h
index b9819f2168..ef031bf0ae 100644
--- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Geeetech/A10M/Configuration.h b/config/examples/Geeetech/A10M/Configuration.h
index 74107f2337..78ae286443 100644
--- a/config/examples/Geeetech/A10M/Configuration.h
+++ b/config/examples/Geeetech/A10M/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -466,7 +461,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h
index fd1bbce4f0..b7840cc896 100644
--- a/config/examples/Geeetech/A10M/Configuration_adv.h
+++ b/config/examples/Geeetech/A10M/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h
index 0e843ec812..41521febaf 100644
--- a/config/examples/Geeetech/A20M/Configuration.h
+++ b/config/examples/Geeetech/A20M/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -466,7 +461,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h
index 6c9217a1ce..2d868bf340 100644
--- a/config/examples/Geeetech/A20M/Configuration_adv.h
+++ b/config/examples/Geeetech/A20M/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h
index 12eeb3e841..bc30ce2490 100644
--- a/config/examples/Geeetech/GT2560/Configuration.h
+++ b/config/examples/Geeetech/GT2560/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -486,7 +481,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
index 127604e98b..2cbb20cc5c 100644
--- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
+++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h
index 6e743fbb77..32bbfb2443 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -480,7 +475,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
index ce1c615b09..0cf2dbf963 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
index 7eeff15cb1..5930323a66 100644
--- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
+++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 125
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -486,7 +481,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
index fe1ad0d193..04e22e1018 100644
--- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
+++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 125
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -486,7 +481,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
index 5ba06365d3..55f06bdab5 100644
--- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
+++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
index f9322ca14a..4481570e44 100644
--- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
+++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
index e9574619cf..bddc892330 100644
--- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
+++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
index f9322ca14a..4481570e44 100644
--- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
+++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h
index 4bed2af0bc..a3dcedd901 100644
--- a/config/examples/Infitary/i3-M508/Configuration.h
+++ b/config/examples/Infitary/i3-M508/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 125
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -480,7 +475,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h
index 2520c4c794..64ff999c46 100644
--- a/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/config/examples/Infitary/i3-M508/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h
index e5355499d2..8f3bc49dea 100644
--- a/config/examples/JGAurora/A5/Configuration.h
+++ b/config/examples/JGAurora/A5/Configuration.h
@@ -396,7 +396,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 // measured to be satisfactorily accurate on center of bed within +/- 1 degC.
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -415,8 +414,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -426,7 +423,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -438,7 +434,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -486,7 +481,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h
index dba7e742d0..6e42a3752e 100644
--- a/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/config/examples/JGAurora/A5/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h
index 98d3013888..9635afe50b 100644
--- a/config/examples/MakerParts/Configuration.h
+++ b/config/examples/MakerParts/Configuration.h
@@ -411,7 +411,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -430,8 +429,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -441,7 +438,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -453,7 +449,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -496,7 +491,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h
index eba5802a90..30283f20f4 100644
--- a/config/examples/MakerParts/Configuration_adv.h
+++ b/config/examples/MakerParts/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h
index 16f30785e0..b75cf688ee 100644
--- a/config/examples/Malyan/M150/Configuration.h
+++ b/config/examples/Malyan/M150/Configuration.h
@@ -399,7 +399,6 @@
// The reasons are inconclusive so I leave at 1
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -418,8 +417,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -429,7 +426,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -441,7 +437,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -484,7 +479,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h
index cec4f67278..571c7026b4 100644
--- a/config/examples/Malyan/M150/Configuration_adv.h
+++ b/config/examples/Malyan/M150/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h
index aef5534b6c..fce109b27b 100644
--- a/config/examples/Malyan/M200/Configuration.h
+++ b/config/examples/Malyan/M200/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 11
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 100
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -475,7 +470,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h
index 70e76c5791..02e5b16e07 100644
--- a/config/examples/Malyan/M200/Configuration_adv.h
+++ b/config/examples/Malyan/M200/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h
index 8646d82b63..1b8d4f8733 100644
--- a/config/examples/Micromake/C1/basic/Configuration.h
+++ b/config/examples/Micromake/C1/basic/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h
index 79af8cfe66..04385e406f 100644
--- a/config/examples/Micromake/C1/enhanced/Configuration.h
+++ b/config/examples/Micromake/C1/enhanced/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index dff6e6ca1a..a7cf91eecf 100644
--- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h
index d07a0f210d..c33b81fe57 100644
--- a/config/examples/Mks/Robin/Configuration.h
+++ b/config/examples/Mks/Robin/Configuration.h
@@ -392,7 +392,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -411,8 +410,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -422,7 +419,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -434,7 +430,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -477,7 +472,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h
index 405e236722..226d4ad0f1 100644
--- a/config/examples/Mks/Robin/Configuration_adv.h
+++ b/config/examples/Mks/Robin/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h
index b767a89866..a0d8278532 100644
--- a/config/examples/Mks/Sbase/Configuration.h
+++ b/config/examples/Mks/Sbase/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h
index f5ee74690c..a34b066c58 100644
--- a/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/config/examples/Mks/Sbase/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h
index 20528942e9..146b602562 100644
--- a/config/examples/Printrbot/PrintrboardG2/Configuration.h
+++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h
@@ -392,7 +392,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -411,8 +410,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -422,7 +419,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -434,7 +430,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -477,7 +472,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h
index 74300e4c60..31295a053e 100644
--- a/config/examples/RapideLite/RL200/Configuration.h
+++ b/config/examples/RapideLite/RL200/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 250
#define HEATER_5_MAXTEMP 250
#define BED_MAXTEMP 120
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h
index 7a1cf1d79f..5889db8074 100644
--- a/config/examples/RapideLite/RL200/Configuration_adv.h
+++ b/config/examples/RapideLite/RL200/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h
index 48071ff2db..f700f548fa 100644
--- a/config/examples/RepRapPro/Huxley/Configuration.h
+++ b/config/examples/RepRapPro/Huxley/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 // Sanguinololu v1.3 with 4.7kOhm pullup
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h
index 90f9d5be9f..3524325916 100644
--- a/config/examples/RepRapWorld/Megatronics/Configuration.h
+++ b/config/examples/RepRapWorld/Megatronics/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h
index b24185f120..c960509189 100644
--- a/config/examples/RigidBot/Configuration.h
+++ b/config/examples/RigidBot/Configuration.h
@@ -394,7 +394,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -413,8 +412,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -424,7 +421,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -436,7 +432,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -479,7 +474,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h
index 6cf8a86130..2607a276b4 100644
--- a/config/examples/RigidBot/Configuration_adv.h
+++ b/config/examples/RigidBot/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/SCARA/Configuration.h b/config/examples/SCARA/Configuration.h
index e3bffd60df..808bc90b1f 100644
--- a/config/examples/SCARA/Configuration.h
+++ b/config/examples/SCARA/Configuration.h
@@ -422,7 +422,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -441,8 +440,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -452,7 +449,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -464,7 +460,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -495,7 +490,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/SCARA/Configuration_adv.h b/config/examples/SCARA/Configuration_adv.h
index 165e7e59c0..ff8768107f 100644
--- a/config/examples/SCARA/Configuration_adv.h
+++ b/config/examples/SCARA/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 3000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h
index d9067bf51d..5939baa236 100644
--- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h
+++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 1
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
index caf83250f1..57d21c1dfc 100644
--- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
+++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/STM32/STM32F10/Configuration.h b/config/examples/STM32/STM32F10/Configuration.h
index 87fe55272f..1d8a02a0e8 100644
--- a/config/examples/STM32/STM32F10/Configuration.h
+++ b/config/examples/STM32/STM32F10/Configuration.h
@@ -392,7 +392,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 998
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 60
@@ -411,8 +410,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -422,7 +419,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -434,7 +430,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -477,7 +472,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/STM32/STM32F4/Configuration.h b/config/examples/STM32/STM32F4/Configuration.h
index 935dd36b04..6055e39f44 100644
--- a/config/examples/STM32/STM32F4/Configuration.h
+++ b/config/examples/STM32/STM32F4/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/STM32/stm32f103ret6/Configuration.h b/config/examples/STM32/stm32f103ret6/Configuration.h
index 4348560590..5eaaceaf84 100644
--- a/config/examples/STM32/stm32f103ret6/Configuration.h
+++ b/config/examples/STM32/stm32f103ret6/Configuration.h
@@ -392,7 +392,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 998
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 60
@@ -411,8 +410,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -422,7 +419,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -434,7 +430,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -477,7 +472,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h
index 861fd20991..9648c4ba38 100644
--- a/config/examples/Sanguinololu/Configuration.h
+++ b/config/examples/Sanguinololu/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h
index 327e47390f..e2f5b592bc 100644
--- a/config/examples/Sanguinololu/Configuration_adv.h
+++ b/config/examples/Sanguinololu/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h
index 76bfe753ae..b86c5ad4ad 100644
--- a/config/examples/TheBorg/Configuration.h
+++ b/config/examples/TheBorg/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h
index a483d4af35..f65039a92e 100644
--- a/config/examples/TheBorg/Configuration_adv.h
+++ b/config/examples/TheBorg/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h
index ffcc2d8e84..a4dd933d37 100644
--- a/config/examples/TinyBoy2/Configuration.h
+++ b/config/examples/TinyBoy2/Configuration.h
@@ -418,7 +418,6 @@
#define TEMP_SENSOR_BED 0
#endif
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -437,8 +436,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -448,7 +445,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -460,7 +456,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 100
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -513,7 +508,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h
index 3b003029a9..e21e8ed5df 100644
--- a/config/examples/TinyBoy2/Configuration_adv.h
+++ b/config/examples/TinyBoy2/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h
index 9bb197dd96..a78d57d9db 100644
--- a/config/examples/Tronxy/X1/Configuration.h
+++ b/config/examples/Tronxy/X1/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 260
#define HEATER_5_MAXTEMP 260
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h
index ce8a3a4da1..1513d66abd 100644
--- a/config/examples/Tronxy/X3A/Configuration.h
+++ b/config/examples/Tronxy/X3A/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 501
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 130
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h
index f83dc8eeba..ed4be90607 100644
--- a/config/examples/Tronxy/X3A/Configuration_adv.h
+++ b/config/examples/Tronxy/X3A/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h
index ab4cc76fc9..a37161a280 100644
--- a/config/examples/Tronxy/X5S-2E/Configuration.h
+++ b/config/examples/Tronxy/X5S-2E/Configuration.h
@@ -393,7 +393,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -412,8 +411,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -423,7 +420,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -439,7 +435,6 @@
// Tronxy X5S-2E:
// The OEM stock model uses a clone MK3a 300 @ 12V with no insulation and can reach a maximum 70C at 25C ambient.
#define BED_MAXTEMP 81
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -489,7 +484,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
index d3b1c340e9..e1b54ab66e 100644
--- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h
+++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h
index 40f976bcb9..06cde48f74 100644
--- a/config/examples/Tronxy/X5S/Configuration.h
+++ b/config/examples/Tronxy/X5S/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -475,7 +470,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h
index c252b570fc..627f95c503 100644
--- a/config/examples/Tronxy/XY100/Configuration.h
+++ b/config/examples/Tronxy/XY100/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -487,7 +482,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h
index 5aeeb3bd95..a92ad948f9 100644
--- a/config/examples/UltiMachine/Archim1/Configuration.h
+++ b/config/examples/UltiMachine/Archim1/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h
index e754919433..0d8c98394c 100644
--- a/config/examples/UltiMachine/Archim1/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h
index f835efc7d3..0411627723 100644
--- a/config/examples/UltiMachine/Archim2/Configuration.h
+++ b/config/examples/UltiMachine/Archim2/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h
index 925b861338..0e03fac07b 100644
--- a/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h
index 0f6f47b604..93265bf12f 100644
--- a/config/examples/VORONDesign/Configuration.h
+++ b/config/examples/VORONDesign/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -481,7 +476,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h
index 2126eb7630..652062c4f5 100644
--- a/config/examples/VORONDesign/Configuration_adv.h
+++ b/config/examples/VORONDesign/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h
index 6839944549..b280258ac1 100644
--- a/config/examples/Velleman/K8200/Configuration.h
+++ b/config/examples/Velleman/K8200/Configuration.h
@@ -411,7 +411,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -430,8 +429,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -441,7 +438,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -453,7 +449,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -500,7 +495,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h
index b948457074..8d242aa799 100644
--- a/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/config/examples/Velleman/K8200/Configuration_adv.h
@@ -59,6 +59,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -140,8 +153,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Velleman/K8400/Configuration.h b/config/examples/Velleman/K8400/Configuration.h
index bb95b7218d..0860d62a9b 100644
--- a/config/examples/Velleman/K8400/Configuration.h
+++ b/config/examples/Velleman/K8400/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Velleman/K8400/Configuration_adv.h b/config/examples/Velleman/K8400/Configuration_adv.h
index 05689a1a8d..e284a534ad 100644
--- a/config/examples/Velleman/K8400/Configuration_adv.h
+++ b/config/examples/Velleman/K8400/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 1000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h
index 5654799872..0f50541dc2 100644
--- a/config/examples/Velleman/K8400/Dual-head/Configuration.h
+++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h
index d72acfc99f..bbe1529234 100644
--- a/config/examples/WASP/PowerWASP/Configuration.h
+++ b/config/examples/WASP/PowerWASP/Configuration.h
@@ -410,7 +410,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -429,8 +428,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -440,7 +437,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -452,7 +448,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -495,7 +490,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h
index 4a68eef176..f67863b5c6 100644
--- a/config/examples/WASP/PowerWASP/Configuration_adv.h
+++ b/config/examples/WASP/PowerWASP/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h
index 3b14ba3799..ac98dac17d 100644
--- a/config/examples/Wanhao/Duplicator 6/Configuration.h
+++ b/config/examples/Wanhao/Duplicator 6/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -481,7 +476,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index da0d9f72c9..c35865bd94 100644
--- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
+++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/adafruit/ST7565/Configuration.h b/config/examples/adafruit/ST7565/Configuration.h
index 8db4706e5b..bd72ff2bc3 100644
--- a/config/examples/adafruit/ST7565/Configuration.h
+++ b/config/examples/adafruit/ST7565/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h
index ec2a9d96c5..f59af6179e 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration.h
@@ -412,7 +412,6 @@
#endif
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -431,8 +430,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -442,7 +439,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -454,7 +450,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 120
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -502,7 +497,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
index 811920708f..a18697673b 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
index dc4ba74f3c..fab7299f5e 100644
--- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 250
#define HEATER_5_MAXTEMP 250
#define BED_MAXTEMP 115
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -481,7 +476,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
index 8717e0a0d3..1a70a19d1a 100644
--- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h
index cbf490cb9e..0de887940a 100644
--- a/config/examples/delta/FLSUN/kossel/Configuration.h
+++ b/config/examples/delta/FLSUN/kossel/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 250
#define HEATER_5_MAXTEMP 250
#define BED_MAXTEMP 115
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -481,7 +476,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h
index 8717e0a0d3..1a70a19d1a 100644
--- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h
index 2277819e7e..056e94b934 100644
--- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h
+++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -481,7 +476,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
index fac00ef9f6..d092a4135a 100644
--- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h
index ea8120b671..29267ce80e 100644
--- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h
+++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
index fac00ef9f6..d092a4135a 100644
--- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
+++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h
index 35262a935a..59b530225b 100644
--- a/config/examples/delta/Hatchbox_Alpha/Configuration.h
+++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h
@@ -396,7 +396,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -415,8 +414,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -426,7 +423,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -438,7 +434,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -486,7 +481,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h
index 2bda8395ca..7756e40eba 100644
--- a/config/examples/delta/MKS/SBASE/Configuration.h
+++ b/config/examples/delta/MKS/SBASE/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h
index 86c6dbdc58..f369a7682b 100644
--- a/config/examples/delta/MKS/SBASE/Configuration_adv.h
+++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h
index 7c1cb2dc0e..dc9e9f22a0 100644
--- a/config/examples/delta/Tevo Little Monster/Configuration.h
+++ b/config/examples/delta/Tevo Little Monster/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -480,7 +475,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h
index 38e80b78d9..161d038aa7 100644
--- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h
+++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h
index 3ef020f114..470c82c21a 100644
--- a/config/examples/delta/generic/Configuration.h
+++ b/config/examples/delta/generic/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h
index fac00ef9f6..d092a4135a 100644
--- a/config/examples/delta/generic/Configuration_adv.h
+++ b/config/examples/delta/generic/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h
index 31ab8f5085..181f699ec5 100644
--- a/config/examples/delta/kossel_mini/Configuration.h
+++ b/config/examples/delta/kossel_mini/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 11
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h
index e3daa9b375..4b078e8d7c 100644
--- a/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h
index c139478cda..75fa32ee6e 100644
--- a/config/examples/delta/kossel_pro/Configuration.h
+++ b/config/examples/delta/kossel_pro/Configuration.h
@@ -395,7 +395,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -414,8 +413,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -425,7 +422,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -437,7 +433,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -468,7 +463,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h
index 5649229a5b..a21d21d9ec 100644
--- a/config/examples/delta/kossel_xl/Configuration.h
+++ b/config/examples/delta/kossel_xl/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -480,7 +475,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h
index d4c3eb599a..50bf1ab510 100644
--- a/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/config/examples/delta/kossel_xl/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h
index 05ddccd0a6..b71bf23935 100644
--- a/config/examples/gCreate/gMax1.5+/Configuration.h
+++ b/config/examples/gCreate/gMax1.5+/Configuration.h
@@ -399,7 +399,6 @@
// a Fortek SSR to do it. If you are using an unaltered gCreate machine, this needs
// to be set to 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -418,8 +417,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -429,7 +426,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -441,7 +437,6 @@
#define HEATER_4_MAXTEMP 245
#define HEATER_5_MAXTEMP 245
#define BED_MAXTEMP 115
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -489,7 +484,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h
index b476cd19cc..49165c0d41 100644
--- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h
index 7abbf252c1..c19ba37b01 100644
--- a/config/examples/makibox/Configuration.h
+++ b/config/examples/makibox/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 12
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -476,7 +471,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h
index e1c2e688bd..31fb062a48 100644
--- a/config/examples/makibox/Configuration_adv.h
+++ b/config/examples/makibox/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h
index 5fb5a512ae..7cd185a3af 100644
--- a/config/examples/tvrrug/Round2/Configuration.h
+++ b/config/examples/tvrrug/Round2/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -465,7 +460,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h
index ae18ae28c4..26f2fb89b2 100644
--- a/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
diff --git a/config/examples/wt150/Configuration.h b/config/examples/wt150/Configuration.h
index 4b5fa0251b..8a0b0401cb 100644
--- a/config/examples/wt150/Configuration.h
+++ b/config/examples/wt150/Configuration.h
@@ -391,7 +391,6 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0
-#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -410,8 +409,6 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
-
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@@ -421,7 +418,6 @@
#define HEATER_4_MINTEMP 5
#define HEATER_5_MINTEMP 5
#define BED_MINTEMP 5
-#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@@ -433,7 +429,6 @@
#define HEATER_4_MAXTEMP 275
#define HEATER_5_MAXTEMP 275
#define BED_MAXTEMP 150
-#define CHAMBER_MAXTEMP 100
//===========================================================================
//============================= PID Settings ================================
@@ -481,7 +476,7 @@
#endif // PIDTEMP
//===========================================================================
-//============================= PID > Bed Temperature Control ===============
+//====================== PID > Bed Temperature Control ======================
//===========================================================================
/**
diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h
index 2c4027bc9d..22cd224d65 100644
--- a/config/examples/wt150/Configuration_adv.h
+++ b/config/examples/wt150/Configuration_adv.h
@@ -50,6 +50,19 @@
#define HEATER_BED_INVERTING true
#endif
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+ #define CHAMBER_MINTEMP 5
+ #define CHAMBER_MAXTEMP 60
+ #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
+ #define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+ //#define CHAMBER_LIMIT_SWITCHING
+ //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
+ //#define HEATER_CHAMBER_INVERTING false
+#endif
+
#if DISABLED(PIDTEMPBED)
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
#if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
#endif
#if ENABLED(PIDTEMP)
- // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
- // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+ // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+ // A well-chosen Kc value should add just enough power to melt the increased material volume.
//#define PID_EXTRUSION_SCALING
#if ENABLED(PID_EXTRUSION_SCALING)
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)