From 7b5d6ba315df18bb33fba7b39503b51fb348eb56 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Jo=C3=A3o=20Br=C3=A1zio?= Date: Sat, 16 Apr 2016 03:20:23 +0100 Subject: [PATCH] Rebase & feedback --- Marlin/Configuration.h | 147 +++++++++++++++++++++-------------------- 1 file changed, 74 insertions(+), 73 deletions(-) diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 0c9e1bc947..23f16b0521 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -604,7 +604,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // O-- FRONT --+ // (0,0) #define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] - #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] + #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] #define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min. @@ -762,7 +762,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // @section lcd // -// MARLIN LANGUAGE +// LCD LANGUAGE // // Here you may choose the language used by Marlin on the LCD menus, the following // list of languages are available: @@ -772,19 +772,18 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) // -// LCD CHARSET +// LCD CHARACTER SET // -// Choose ONE of the following charset list, keep in mind that this selection is -// dependent on your physical hardware thus it has to match the type of Character -// based LCD you have. +// Choose ONE of the following charset options. This selection depends on +// your physical hardware, so it must match your character-based LCD. // -// Note: This options is ignored for a full graphic display. +// Note: This option is NOT applicable to graphical displays. // -// To find out what type you have: -// - Compile and upload with language set to 'test' -// - Click to get the menu +// To find out what type of display you have: +// - Compile and upload with the language (above) set to 'test' +// - Click the controller to view the LCD menu // -// You'll see two typical lines from the upper half of the charset. +// The LCD will display two lines from the upper half of the character set. // // See also https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language // @@ -797,10 +796,10 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // // You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2, // 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels -// (ST7565R family). +// (ST7565R family). (This option will be set automatically for certain displays.) // -// IMPORTANT NOTE: You have to install Arduino's U8glib library for the Full -// Graphics Display to work ! - https://github.com/olikraus/U8glib_Arduino +// IMPORTANT NOTE: The U8glib library is required for Full Graphic Display! +// https://github.com/olikraus/U8glib_Arduino // //#define ULTRA_LCD // Character based //#define DOGLCD // Full graphics display @@ -808,16 +807,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // // SD CARD // -// SD card support is now disabled by default, if you have [and want] SD support -// then you must uncomment the following directive. +// SD Card support is disabled by default. If your controller has an SD slot, +// you must uncomment the following option or it won't work. // //#define SDSUPPORT // // SD CARD: SPI SPEED // -// You may uncomment *one* of the following directives to use slower SPI transfer -// speeds, this is usually required if you're getting volume init errors. +// Uncomment ONE of the following items to use a slower SPI transfer +// speed. This is usually required if you're getting volume init errors. // //#define SPI_SPEED SPI_HALF_SPEED //#define SPI_SPEED SPI_QUARTER_SPEED @@ -833,35 +832,36 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // // ENCODER SETTINGS // -// This option defines how many pulses a encoder should produce for a menu -// step to be produced, you should increase this value for highres encoders. +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. // //#define ENCODER_PULSES_PER_STEP 1 + // -// -// This option defines how many steps are required for Marlin to move between -// next/prev menu items. +// Use this option to override the number of step signals required to +// move between next/prev menu items. // //#define ENCODER_STEPS_PER_MENU_ITEM 5 + // -// -// This option allows you to reverse the direction you have to turn the encoder -// to navigate up/down on the menus, by default CLOCKWISE rotation moves DOWN in -// the LCD menu, when active CLOCKWISE rotation will move UP in the LCD menu. +// This option reverses the encoder direction for navigating LCD menus. +// By default CLOCKWISE == DOWN. With this enabled CLOCKWISE == UP. // //#define REVERSE_MENU_DIRECTION + // +// SPEAKER/BUZZER // -// If you have a speaker activate this directive to enable it. -// By default Marlin assumes your setup is buzzer based and no action is required. +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. // //#define SPEAKER + // -// The duration and frequency the buzzer plays the UI feedback sound. -// You may define these directives with 0 (zero) if you want to disable all sound -// feedback from Marlin. +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. // -// Note: You may test the buzzing sound with the G-Code: +// Note: Test audio output with the G-Code: // M300 S P // //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 @@ -870,81 +870,81 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // // CONTROLLER TYPE: Standard // -// Marlin supports a impressive variety of controllers, uncomment the directive -// which defines physical controller you're using. +// Marlin supports a wide variety of controllers. +// Enable one of the following options to specify your controller. // + // -// Activate this directive if you have an ULTIMAKER Controller. +// ULTIMAKER Controller. // //#define ULTIMAKERCONTROLLER + // -// -// Activate this directive if you have a ULTIPANEL as seen on Thingiverse. +// ULTIPANEL as seen on Thingiverse. // //#define ULTIPANEL + // -// -// Activate this directive if you have a PanelOne from T3P3 -// (via RAMPS 1.4 AUX2/AUX3) - http://reprap.org/wiki/PanelOne +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne // //#define PANEL_ONE + // -// -// Activate this directive if you have a MaKr3d Makr-Panel with graphic -// controller and SD suppord - http://reprap.org/wiki/MaKr3d_MaKrPanel +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel // //#define MAKRPANEL + // -// -// Activate one of these directives if you have a Panucatt Devices Viki 2.0 or -// mini Viki with Graphic LCD - http://panucatt.com +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com // //#define VIKI2 //#define miniVIKI -// This is a new controller currently under development. https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ // -// -// Activate this directive if you have an Adafruit ST7565 Full Graphic Controller. +// Adafruit ST7565 Full Graphic Controller. // https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ // //#define ELB_FULL_GRAPHIC_CONTROLLER + // -// -// Activate this directive if you have a RepRapDiscount Smart Controller. +// RepRapDiscount Smart Controller. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller // -// Note: Usually sold in a white PCB. +// Note: Usually sold with a white PCB. // //#define REPRAP_DISCOUNT_SMART_CONTROLLER + // -// -// Activate this directive if you have a BQ LCD Smart Controller shipped by +// BQ LCD Smart Controller shipped by // default with the BQ Hephestos 2 and Witbox 2. // //#define BQ_LCD_SMART_CONTROLLER + // -// -// Activate this directive if you have a GADGETS3D G3D LCD/SD Controller +// GADGETS3D G3D LCD/SD Controller // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel // -// Note: Usually sold in a blue PCB. +// Note: Usually sold with a blue PCB. // //#define G3D_PANEL + // -// -// Activate this directive if you have a RepRapDiscount FULL GRAPHIC Smart Controller +// RepRapDiscount FULL GRAPHIC Smart Controller // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller // // #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + // -// -// Activate this directive if you have a MakerLab Mini Panel with graphic +// MakerLab Mini Panel with graphic // controller and SD support - http://reprap.org/wiki/Mini_panel //#define MINIPANEL + // -// -// Activate this directive if you have a RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 // http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 // // REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key @@ -959,20 +959,21 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // Note: These controllers require the installation of Arduino's LiquidCrystal_I2C // library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C // + // -// Activate this directive if you have an Elefu RA Board Control Panel +// Elefu RA Board Control Panel // http://www.elefu.com/index.php?route=product/product&product_id=53 // //#define RA_CONTROL_PANEL //#define LCD_I2C_SAINSMART_YWROBOT + // -// -// Activate this directive if you have a LCM160 LCD adapter. +// LCM160 LCD adapter. // //#define LCM1602 + // -// -// Activate this directive if you have a PANELOLU2 LCD with status LEDs, +// PANELOLU2 LCD with status LEDs, // separate encoder and click inputs. // // Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. @@ -982,15 +983,15 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). // //#define LCD_I2C_PANELOLU2 + // -// -// Activate this directive if you have a Panucatt VIKI LCD with status LEDs, +// Panucatt VIKI LCD with status LEDs, // integrated click & L/R/U/D buttons, separate encoder inputs. // //#define LCD_I2C_VIKI + // -// -// Activate this directive if you have a SSD1306 OLED full graphics generic display +// SSD1306 OLED full graphics generic display // //#define U8GLIB_SSD1306