diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 1fe970a660..b99ec6a29e 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -1,6 +1,8 @@ #ifndef CONFIGURATION_H #define CONFIGURATION_H +#include "boards.h" + // This configuration file contains the basic settings. // Advanced settings can be found in Configuration_adv.h // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration @@ -36,54 +38,10 @@ // This enables the serial port associated to the Bluetooth interface //#define BTENABLED // Enable BT interface on AT90USB devices - -//// The following define selects which electronics board you have. Please choose the one that matches your setup -// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics" -// 11 = Gen7 v1.1, v1.2 = 11 -// 12 = Gen7 v1.3 -// 13 = Gen7 v1.4 -// 2 = Cheaptronic v1.0 -// 20 = Sethi 3D_1 -// 3 = MEGA/RAMPS up to 1.2 = 3 -// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed) -// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed) -// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan) -// 36 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan) -// 4 = Duemilanove w/ ATMega328P pin assignment -// 5 = Gen6 -// 51 = Gen6 deluxe -// 6 = Sanguinololu < 1.2 -// 62 = Sanguinololu 1.2 and above -// 63 = Melzi -// 64 = STB V1.1 -// 65 = Azteeg X1 -// 66 = Melzi with ATmega1284 (MaKr3d version) -// 67 = Azteeg X3 -// 68 = Azteeg X3 Pro -// 7 = Ultimaker -// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare) -// 72 = Ultimainboard 2.x (Uses TEMP_SENSOR 20) -// 77 = 3Drag Controller -// 8 = Teensylu -// 80 = Rumba -// 81 = Printrboard (AT90USB1286) -// 82 = Brainwave (AT90USB646) -// 83 = SAV Mk-I (AT90USB1286) -// 84 = Teensy++2.0 (AT90USB1286) // CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make -// 9 = Gen3+ -// 22 = Gen3 Monolithic Electronics -// 70 = Megatronics -// 701= Megatronics v2.0 -// 702= Minitronics v1.0 -// 90 = Alpha OMCA board -// 91 = Final OMCA board -// 301= Rambo -// 21 = Elefu Ra Board (v3) -// 88 = 5DPrint D8 Driver Board -// 999 = Leapfrog - +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup #ifndef MOTHERBOARD -#define MOTHERBOARD 7 + #define MOTHERBOARD BOARD_ULTIMAKER #endif // Define this to set a custom name for your generic Mendel, diff --git a/Marlin/boards.h b/Marlin/boards.h new file mode 100644 index 0000000000..af249c78cf --- /dev/null +++ b/Marlin/boards.h @@ -0,0 +1,55 @@ +#ifndef BOARDS_H +#define BOARDS_H + +#define BOARD_UNKNOWN -1 + +#define BOARD_GEN7_CUSTOM 10 // Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics" +#define BOARD_GEN7_12 11 // Gen7 v1.1, v1.2 +#define BOARD_GEN7_13 12 // Gen7 v1.3 +#define BOARD_GEN7_14 13 // Gen7 v1.4 +#define BOARD_CHEAPTRONIC 2 // Cheaptronic v1.0 +#define BOARD_SETHI 20 // Sethi 3D_1 +#define BOARD_RAMPS_OLD 3 // MEGA/RAMPS up to 1.2 +#define BOARD_RAMPS_13_EFB 33 // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed) +#define BOARD_RAMPS_13_EEB 34 // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed) +#define BOARD_RAMPS_13_EFF 35 // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan) +#define BOARD_RAMPS_13_EEF 36 // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan) +#define BOARD_DUEMILANOVE_328P 4 // Duemilanove w/ ATMega328P pin assignment +#define BOARD_GEN6 5 // Gen6 +#define BOARD_GEN6_DELUXE 51 // Gen6 deluxe +#define BOARD_SANGUINOLOLU_11 6 // Sanguinololu < 1.2 +#define BOARD_SANGUINOLOLU_12 62 // Sanguinololu 1.2 and above +#define BOARD_MELZI 63 // Melzi +#define BOARD_STB_11 64 // STB V1.1 +#define BOARD_AZTEEG_X1 65 // Azteeg X1 +#define BOARD_MELZI_1284 66 // Melzi with ATmega1284 (MaKr3d version) +#define BOARD_AZTEEG_X3 67 // Azteeg X3 +#define BOARD_AZTEEG_X3_PRO 68 // Azteeg X3 Pro +#define BOARD_ULTIMAKER 7 // Ultimaker +#define BOARD_ULTIMAKER_OLD 71 // Ultimaker (Older electronics. Pre 1.5.4. This is rare) +#define BOARD_ULTIMAIN_2 72 // Ultimainboard 2.x (Uses TEMP_SENSOR 20) +#define BOARD_3DRAG 77 // 3Drag Controller +#define BOARD_TEENSYLU 8 // Teensylu +#define BOARD_RUMBA 80 // Rumba +#define BOARD_PRINTRBOARD 81 // Printrboard (AT90USB1286) +#define BOARD_BRAINWAVE 82 // Brainwave (AT90USB646) +#define BOARD_SAV_MKI 83 // SAV Mk-I (AT90USB1286) +#define BOARD_TEENSY2 84 // Teensy++2.0 (AT90USB1286) - CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make +#define BOARD_GEN3_PLUS 9 // Gen3+ +#define BOARD_GEN3_MONOLITHIC 22 // Gen3 Monolithic Electronics +#define BOARD_MEGATRONICS 70 // Megatronics +#define BOARD_MEGATRONICS_2 701 // Megatronics v2.0 +#define BOARD_MEGATRONICS_1 702 // Minitronics v1.0 +#define BOARD_OMCA_A 90 // Alpha OMCA board +#define BOARD_OMCA 91 // Final OMCA board +#define BOARD_RAMBO 301 // Rambo +#define BOARD_ELEFU_3 21 // Elefu Ra Board (v3) +#define BOARD_5DPRINT 88 // 5DPrint D8 Driver Board +#define BOARD_LEAPFROG 999 // Leapfrog + +#define BOARD_99 99 // This is in pins.h but...? + +#define MB(board) (MOTHERBOARD==BOARD_##board) +#define IS_RAMPS (MB(RAMPS_OLD) || MB(RAMPS_13_EFB) || MB(RAMPS_13_EEB) || MB(RAMPS_13_EFF) || MB(RAMPS_13_EEF)) + +#endif //__BOARDS_H diff --git a/Marlin/digipot_mcp4451.cpp b/Marlin/digipot_mcp4451.cpp index 7c150558bc..0ced287aa0 100644 --- a/Marlin/digipot_mcp4451.cpp +++ b/Marlin/digipot_mcp4451.cpp @@ -6,7 +6,7 @@ #include "Wire.h" // Settings for the I2C based DIGIPOT (MCP4451) on Azteeg X3 Pro -#if MOTHERBOARD == 88 +#if MB(5DPRINT) #define DIGIPOT_I2C_FACTOR 117.96 #define DIGIPOT_I2C_MAX_CURRENT 1.736 #else diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index 6b74b0c20b..f6cb2d2a3a 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -1,6 +1,8 @@ #ifndef CONFIGURATION_H #define CONFIGURATION_H +#include "boards.h" + // This configuration file contains the basic settings. // Advanced settings can be found in Configuration_adv.h // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration @@ -55,52 +57,10 @@ // This enables the serial port associated to the Bluetooth interface //#define BTENABLED // Enable BT interface on AT90USB devices - -//// The following define selects which electronics board you have. Please choose the one that matches your setup -// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics" -// 11 = Gen7 v1.1, v1.2 = 11 -// 12 = Gen7 v1.3 -// 13 = Gen7 v1.4 -// 131 = OpenHardware.co.za custom Gen7 electronics -// 2 = Cheaptronic v1.0 -// 20 = Sethi 3D_1 -// 3 = MEGA/RAMPS up to 1.2 = 3 -// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed) -// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed) -// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan) -// 4 = Duemilanove w/ ATMega328P pin assignment -// 5 = Gen6 -// 51 = Gen6 deluxe -// 6 = Sanguinololu < 1.2 -// 62 = Sanguinololu 1.2 and above -// 63 = Melzi -// 64 = STB V1.1 -// 65 = Azteeg X1 -// 66 = Melzi with ATmega1284 (MaKr3d version) -// 67 = Azteeg X3 -// 68 = Azteeg X3 Pro -// 7 = Ultimaker -// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare) -// 72 = Ultimainboard 2.x (Uses TEMP_SENSOR 20) -// 77 = 3Drag Controller -// 8 = Teensylu -// 80 = Rumba -// 81 = Printrboard (AT90USB1286) -// 82 = Brainwave (AT90USB646) -// 83 = SAV Mk-I (AT90USB1286) -// 84 = Teensy++2.0 (AT90USB1286) // CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make -// 9 = Gen3+ -// 70 = Megatronics -// 701= Megatronics v2.0 -// 702= Minitronics v1.0 -// 90 = Alpha OMCA board -// 91 = Final OMCA board -// 301= Rambo -// 21 = Elefu Ra Board (v3) -// 88 = 5DPrint D8 Driver Board - +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup #ifndef MOTHERBOARD -#define MOTHERBOARD 33 + #define MOTHERBOARD BOARD_RAMPS_13_EFB #endif // Define this to set a custom name for your generic Mendel, diff --git a/Marlin/example_configurations/delta/Configuration.h b/Marlin/example_configurations/delta/Configuration.h index 042b221c32..c618dd34b4 100644 --- a/Marlin/example_configurations/delta/Configuration.h +++ b/Marlin/example_configurations/delta/Configuration.h @@ -1,6 +1,8 @@ #ifndef CONFIGURATION_H #define CONFIGURATION_H +#include "boards.h" + // This configuration file contains the basic settings. // Advanced settings can be found in Configuration_adv.h // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration @@ -29,53 +31,10 @@ // This enables the serial port associated to the Bluetooth interface //#define BTENABLED // Enable BT interface on AT90USB devices - -//// The following define selects which electronics board you have. Please choose the one that matches your setup -// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics" -// 11 = Gen7 v1.1, v1.2 = 11 -// 12 = Gen7 v1.3 -// 13 = Gen7 v1.4 -// 2 = Cheaptronic v1.0 -// 20 = Sethi 3D_1 -// 3 = MEGA/RAMPS up to 1.2 = 3 -// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed) -// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed) -// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan) -// 36 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan) -// 4 = Duemilanove w/ ATMega328P pin assignment -// 5 = Gen6 -// 51 = Gen6 deluxe -// 6 = Sanguinololu < 1.2 -// 62 = Sanguinololu 1.2 and above -// 63 = Melzi -// 64 = STB V1.1 -// 65 = Azteeg X1 -// 66 = Melzi with ATmega1284 (MaKr3d version) -// 67 = Azteeg X3 -// 68 = Azteeg X3 Pro -// 7 = Ultimaker -// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare) -// 72 = Ultimainboard 2.x (Uses TEMP_SENSOR 20) -// 77 = 3Drag Controller -// 8 = Teensylu -// 80 = Rumba -// 81 = Printrboard (AT90USB1286) -// 82 = Brainwave (AT90USB646) -// 83 = SAV Mk-I (AT90USB1286) -// 84 = Teensy++2.0 (AT90USB1286) // CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make -// 9 = Gen3+ -// 70 = Megatronics -// 701= Megatronics v2.0 -// 702= Minitronics v1.0 -// 90 = Alpha OMCA board -// 91 = Final OMCA board -// 301= Rambo -// 21 = Elefu Ra Board (v3) -// 88 = 5DPrint D8 Driver Board -// 999 = Leapfrog - +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup #ifndef MOTHERBOARD -#define MOTHERBOARD 33 + #define MOTHERBOARD BOARD_RAMPS_13_EFB #endif // Define this to set a custom name for your generic Mendel, diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index 6ebd08f43e..07c4c586c4 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -1,6 +1,8 @@ #ifndef CONFIGURATION_H #define CONFIGURATION_H +#include "boards.h" + // This configuration file contains the basic settings. // Advanced settings can be found in Configuration_adv.h // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration @@ -30,50 +32,10 @@ // This enables the serial port associated to the Bluetooth interface //#define BTENABLED // Enable BT interface on AT90USB devices - -//// The following define selects which electronics board you have. Please choose the one that matches your setup -// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics" -// 11 = Gen7 v1.1, v1.2 = 11 -// 12 = Gen7 v1.3 -// 13 = Gen7 v1.4 -// 2 = Cheaptronic v1.0 -// 20 = Sethi 3D_1 -// 3 = MEGA/RAMPS up to 1.2 = 3 -// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed) -// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed) -// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan) -// 4 = Duemilanove w/ ATMega328P pin assignment -// 5 = Gen6 -// 51 = Gen6 deluxe -// 6 = Sanguinololu < 1.2 -// 62 = Sanguinololu 1.2 and above -// 63 = Melzi -// 64 = STB V1.1 -// 65 = Azteeg X1 -// 66 = Melzi with ATmega1284 (MaKr3d version) -// 67 = Azteeg X3 -// 68 = Azteeg X3 Pro -// 7 = Ultimaker -// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare) -// 72 = Ultimainboard 2.x (Uses TEMP_SENSOR 20) -// 77 = 3Drag Controller -// 8 = Teensylu -// 80 = Rumba -// 81 = Printrboard (AT90USB1286) -// 82 = Brainwave (AT90USB646) -// 83 = SAV Mk-I (AT90USB1286) -// 9 = Gen3+ -// 70 = Megatronics -// 701= Megatronics v2.0 -// 702= Minitronics v1.0 -// 90 = Alpha OMCA board -// 91 = Final OMCA board -// 301= Rambo -// 21 = Elefu Ra Board (v3) -// 88 = 5DPrint D8 Driver Board - +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup #ifndef MOTHERBOARD -#define MOTHERBOARD 88 + #define MOTHERBOARD BOARD_5DPRINT #endif // Define this to set a custom name for your generic Mendel, diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index 527431a5b9..34be1d2de3 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -1,6 +1,8 @@ #ifndef CONFIGURATION_H #define CONFIGURATION_H +#include "boards.h" + // This configuration file contains the basic settings. // Advanced settings can be found in Configuration_adv.h // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration @@ -36,53 +38,10 @@ // This enables the serial port associated to the Bluetooth interface //#define BTENABLED // Enable BT interface on AT90USB devices - -//// The following define selects which electronics board you have. Please choose the one that matches your setup -// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics" -// 11 = Gen7 v1.1, v1.2 = 11 -// 12 = Gen7 v1.3 -// 13 = Gen7 v1.4 -// 2 = Cheaptronic v1.0 -// 20 = Sethi 3D_1 -// 3 = MEGA/RAMPS up to 1.2 = 3 -// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed) -// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed) -// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan) -// 36 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan) -// 4 = Duemilanove w/ ATMega328P pin assignment -// 5 = Gen6 -// 51 = Gen6 deluxe -// 6 = Sanguinololu < 1.2 -// 62 = Sanguinololu 1.2 and above -// 63 = Melzi -// 64 = STB V1.1 -// 65 = Azteeg X1 -// 66 = Melzi with ATmega1284 (MaKr3d version) -// 67 = Azteeg X3 -// 68 = Azteeg X3 Pro -// 7 = Ultimaker -// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare) -// 72 = Ultimainboard 2.x (Uses TEMP_SENSOR 20) -// 77 = 3Drag Controller -// 8 = Teensylu -// 80 = Rumba -// 81 = Printrboard (AT90USB1286) -// 82 = Brainwave (AT90USB646) -// 83 = SAV Mk-I (AT90USB1286) -// 84 = Teensy++2.0 (AT90USB1286) // CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make -// 9 = Gen3+ -// 70 = Megatronics -// 701= Megatronics v2.0 -// 702= Minitronics v1.0 -// 90 = Alpha OMCA board -// 91 = Final OMCA board -// 301= Rambo -// 21 = Elefu Ra Board (v3) -// 88 = 5DPrint D8 Driver Board -// 999 = Leapfrog - +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup #ifndef MOTHERBOARD -#define MOTHERBOARD 91 + #define MOTHERBOARD BOARD_OMCA #endif // Define this to set a custom name for your generic Mendel, diff --git a/Marlin/language.h b/Marlin/language.h index 9ab5df73eb..2e54a8860c 100644 --- a/Marlin/language.h +++ b/Marlin/language.h @@ -31,16 +31,16 @@ #define PROTOCOL_VERSION "1.0" -#if MOTHERBOARD == 7 || MOTHERBOARD == 71 || MOTHERBOARD == 72 +#if MB(ULTIMAKER)|| MB(ULTIMAKER_OLD)|| MB(ULTIMAIN_2) #define MACHINE_NAME "Ultimaker" #define FIRMWARE_URL "http://firmware.ultimaker.com" -#elif MOTHERBOARD == 80 +#elif MB(RUMBA) #define MACHINE_NAME "Rumba" #define FIRMWARE_URL "https://github.com/ErikZalm/Marlin/" -#elif MOTHERBOARD == 77 +#elif MB(3DRAG) #define MACHINE_NAME "3Drag" #define FIRMWARE_URL "http://3dprint.elettronicain.it/" -#elif MOTHERBOARD == 88 +#elif MB(5DPRINT) #define MACHINE_NAME "Makibox" #define FIRMWARE_URL "https://github.com/ErikZalm/Marlin/" #else diff --git a/Marlin/pins.h b/Marlin/pins.h index 13cb9053e9..906522b81e 100644 --- a/Marlin/pins.h +++ b/Marlin/pins.h @@ -1,7 +1,9 @@ #ifndef PINS_H #define PINS_H -#if MOTHERBOARD != 88 +#include "boards.h" + +#if !MB(5DPRINT) #define X_MS1_PIN -1 #define X_MS2_PIN -1 #define Y_MS1_PIN -1 @@ -20,7 +22,7 @@ * https://bitbucket.org/makible/5dprint-d8-controller-board ****************************************************************************************/ -#if MOTHERBOARD == 88 +#if MB(5DPRINT) #define KNOWN_BOARD 1 #define AT90USB 1286 // Disable MarlinSerial etc. @@ -92,13 +94,13 @@ #define E0_MS1_PIN 5 #define E0_MS2_PIN 4 -#endif /* 88 */ +#endif // 5DPRINT /**************************************************************************************** * Leapfrog Driver board * ****************************************************************************************/ -#if MOTHERBOARD == 999 // Leapfrog board +#if MB(LEAPFROG) // Leapfrog board #define KNOWN_BOARD 1 #ifndef __AVR_ATmega1280__ @@ -162,14 +164,14 @@ /* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */ -#endif +#endif // LEAPFROG /**************************************************************************************** * * ****************************************************************************************/ -#if MOTHERBOARD == 99 +#if MB(99) #define KNOWN_BOARD 1 #define X_STEP_PIN 2 @@ -207,14 +209,14 @@ #define HEATER_BED_PIN 4 #define TEMP_BED_PIN 10 -#endif /* 99 */ +#endif // 99 /**************************************************************************************** * Sethi 3D_1 pin assignment - www.sethi3d.com.br * ****************************************************************************************/ -#if MOTHERBOARD == 20 +#if MB(SETHI) #define KNOWN_BOARD #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__) @@ -285,7 +287,7 @@ #define TX_ENABLE_PIN 12 #define RX_ENABLE_PIN 13 -#endif +#endif // SETHI /**************************************************************************************** * Gen7 v1.1, v1.2, v1.3 pin assignment @@ -293,12 +295,12 @@ ****************************************************************************************/ -#if MOTHERBOARD == 12 -#define MOTHERBOARD 11 +#if MB(GEN7_13) +#define MOTHERBOARD BOARD_GEN7_12 #define GEN7_VERSION 13 // v1.3 #endif -#if MOTHERBOARD == 11 +#if MB(GEN7_12) #define KNOWN_BOARD #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__) @@ -376,11 +378,11 @@ * ****************************************************************************************/ -#if MOTHERBOARD == 13 +#if MB(GEN7_14) #define GEN7_VERSION 14 // v1.4 #endif -#if MOTHERBOARD == 13 +#if MB(GEN7_14) #define KNOWN_BOARD #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__) @@ -442,22 +444,19 @@ #define TX_ENABLE_PIN 12 #define RX_ENABLE_PIN 13 -#endif +#endif // GEN7 -/******************************************************************************* -********* +/****************************************************************************** * Gen7 Alfons3 pin assignment * -******************************************************************************** -********/ +******************************************************************************/ /* These Pins are assigned for the modified GEN7 Board from Alfons3 Please review the pins and adjust it for your needs*/ -#if MOTHERBOARD == 10 +#if MB(GEN7_CUSTOM) #define KNOWN_BOARD #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__) #error Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu. - #endif //x axis pins @@ -525,13 +524,13 @@ #define BTN_EN2 10 #define BTN_ENC 12 //the click -#endif +#endif // GEN7_CUSTOM /**************************************************************************************** * Arduino Mega pin assignment * ****************************************************************************************/ -#if MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 36 || MOTHERBOARD == 77 || MOTHERBOARD == 67 || MOTHERBOARD == 68 +#if IS_RAMPS || MB(3DRAG) || MB(AZTEEG_X3) || MB(AZTEEG_X3_PRO) #define KNOWN_BOARD 1 //////////////////FIX THIS////////////// @@ -547,11 +546,11 @@ // #define RAMPS_V_1_0 -#if MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 36 || MOTHERBOARD == 77 || MOTHERBOARD == 67 || MOTHERBOARD == 68 +#if (IS_RAMPS && !MB(RAMPS_OLD)) || MB(3DRAG) || MB(AZTEEG_X3) || MB(AZTEEG_X3_PRO) #define LARGE_FLASH true - #if MOTHERBOARD == 77 + #if MB(3DRAG) #define X_STEP_PIN 54 #define X_DIR_PIN 55 #define X_ENABLE_PIN 38 @@ -628,16 +627,16 @@ #define E1_DIR_PIN 34 #define E1_ENABLE_PIN 30 -#if MOTHERBOARD == 34 //FMM added for Filament Extruder +#if MB(RAMPS_13_EEB) //FMM added for Filament Extruder #ifdef FILAMENT_SENSOR - //define analog pin for the filament width sensor input - //Use the RAMPS 1.4 Analog input 5 on the AUX2 connector + //define analog pin for the filament width sensor input + //Use the RAMPS 1.4 Analog input 5 on the AUX2 connector #define FILWIDTH_PIN 5 #endif #endif - #if MOTHERBOARD == 68 + #if MB(AZTEEG_X3_PRO) #define E2_STEP_PIN 23 #define E2_DIR_PIN 25 #define E2_ENABLE_PIN 40 @@ -656,17 +655,17 @@ #define LED_PIN 13 #endif - #if MOTHERBOARD == 33 || MOTHERBOARD == 35 || MOTHERBOARD == 67 || MOTHERBOARD == 68 + #if MB(RAMPS_13_EFB) || MB(RAMPS_13_EFF) || MB(AZTEEG_X3) || MB(AZTEEG_X3_PRO) #define FAN_PIN 9 // (Sprinter config) #else #define FAN_PIN 4 // IO pin. Buffer needed #endif - #if MOTHERBOARD == 77 || MOTHERBOARD == 36 + #if MB(3DRAG) || MB(RAMPS_13_EEF) #define FAN_PIN 8 #endif - #if MOTHERBOARD == 35 + #if MB(RAMPS_13_EFF) #define CONTROLLERFAN_PIN -1 //Pin used for the fan to cool controller #endif @@ -678,24 +677,24 @@ #define KILL_PIN -1 #endif - #if MOTHERBOARD == 35 + #if MB(RAMPS_13_EFF) #define HEATER_0_PIN 8 #else #define HEATER_0_PIN 10 // EXTRUDER 1 #endif - #if MOTHERBOARD == 33 || MOTHERBOARD == 67 + #if MB(RAMPS_13_EFB) || MB(AZTEEG_X3) #define HEATER_1_PIN -1 #else #define HEATER_1_PIN 9 // EXTRUDER 2 (FAN On Sprinter) #endif - #if MOTHERBOARD == 77 + #if MB(3DRAG) #define HEATER_0_PIN 10 #define HEATER_1_PIN 12 #define HEATER_2_PIN 6 - #elif MOTHERBOARD == 68 + #elif MB(AZTEEG_X3_PRO) #define HEATER_2_PIN 16 #define HEATER_3_PIN 17 #define HEATER_4_PIN 4 @@ -708,7 +707,7 @@ #define TEMP_0_PIN 13 // ANALOG NUMBERING #define TEMP_1_PIN 15 // ANALOG NUMBERING - #if MOTHERBOARD == 68 + #if MB(AZTEEG_X3_PRO) #define TEMP_2_PIN 12 // ANALOG NUMBERING #define TEMP_3_PIN 11 // ANALOG NUMBERING #define TEMP_4_PIN 10 // ANALOG NUMBERING @@ -718,10 +717,10 @@ #define TEMP_2_PIN -1 // ANALOG NUMBERING #endif - #if MOTHERBOARD == 35 || MOTHERBOARD == 36 + #if MB(RAMPS_13_EFF) || MB(RAMPS_13_EEF) #define HEATER_BED_PIN -1 // NO BED #else - #if MOTHERBOARD == 77 + #if MB(3DRAG) #define HEATER_BED_PIN 9 // BED #else #define HEATER_BED_PIN 8 // BED @@ -746,12 +745,12 @@ #endif #endif - #if MOTHERBOARD == 68 + #if MB(AZTEEG_X3_PRO) #define BEEPER 33 #endif #ifdef TEMP_STAT_LEDS - #if MOTHERBOARD == 67 + #if MB(AZTEEG_X3) #define STAT_LED_RED 6 #define STAT_LED_BLUE 11 #endif @@ -814,7 +813,7 @@ #endif - #if MOTHERBOARD == 77 + #if MB(3DRAG) #define BEEPER -1 #define LCD_PINS_RS 27 @@ -832,10 +831,10 @@ #endif #else //old style panel with shift register //arduino pin witch triggers an piezzo beeper - #define BEEPER 33 //No Beeper added + #define BEEPER 33 //No Beeper added //buttons are attached to a shift register - // Not wired this yet + // Not wired this yet //#define SHIFT_CLK 38 //#define SHIFT_LD 42 //#define SHIFT_OUT 40 @@ -850,7 +849,7 @@ #endif #endif //ULTRA_LCD -#else // RAMPS_V_1_1 or RAMPS_V_1_2 as default (MOTHERBOARD == 3) +#else // RAMPS_V_1_1 or RAMPS_V_1_2 as default (BOARD_RAMPS_OLD) #define X_STEP_PIN 26 #define X_DIR_PIN 28 @@ -896,7 +895,7 @@ #define TEMP_2_PIN -1 #define TEMP_BED_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! -#endif // MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 77 +#endif // RAMPS_13_EFB || RAMPS_13_EEB || RAMPS_13_EFF || 3DRAG // SPI for Max6675 Thermocouple @@ -910,13 +909,13 @@ #define MAX6675_SS 49 #endif -#endif //MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 77 +#endif // RAMPS_OLD || RAMPS_13_EFB || RAMPS_13_EEB || RAMPS_13_EFF || 3DRAG /**************************************************************************************** * Duemilanove w/ ATMega328P pin assignment * ****************************************************************************************/ -#if MOTHERBOARD == 4 +#if MB(DUEMILANOVE_328P) #define KNOWN_BOARD 1 #ifndef __AVR_ATmega328P__ @@ -958,25 +957,25 @@ #define HEATER_BED_PIN -1 #define TEMP_BED_PIN -1 -#endif +#endif // DUEMILANOVE_328P /**************************************************************************************** * Elefu RA Board Pin Assignments * ****************************************************************************************/ -#if MOTHERBOARD == 21 -#define KNOWN_BOARD 1 +#if MB(ELEFU_3) +#define KNOWN_BOARD 1 #ifndef __AVR_ATmega2560__ #error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu. #endif -#define X_STEP_PIN 49 -#define X_DIR_PIN 13 -#define X_ENABLE_PIN 48 -#define X_MIN_PIN 35 -#define X_MAX_PIN -1 //34 +#define X_STEP_PIN 49 +#define X_DIR_PIN 13 +#define X_ENABLE_PIN 48 +#define X_MIN_PIN 35 +#define X_MAX_PIN -1 //34 #define Y_STEP_PIN 11 #define Y_DIR_PIN 9 @@ -1008,18 +1007,18 @@ #define FAN_PIN 16 //5V PWM #define PS_ON_PIN 10 //Set to -1 if using a manual switch on the PWRSW Connector -#define SLEEP_WAKE_PIN 26 //This feature still needs work +#define SLEEP_WAKE_PIN 26 //This feature still needs work -#define HEATER_0_PIN 45 //12V PWM1 -#define HEATER_1_PIN 46 //12V PWM2 -#define HEATER_2_PIN 17 //12V PWM3 -#define HEATER_BED_PIN 44 //DOUBLE 12V PWM -#define TEMP_0_PIN 3 //ANALOG NUMBERING -#define TEMP_1_PIN 2 //ANALOG NUMBERING -#define TEMP_2_PIN 1 //ANALOG NUMBERING -#define TEMP_BED_PIN 0 //ANALOG NUMBERING +#define HEATER_0_PIN 45 //12V PWM1 +#define HEATER_1_PIN 46 //12V PWM2 +#define HEATER_2_PIN 17 //12V PWM3 +#define HEATER_BED_PIN 44 //DOUBLE 12V PWM +#define TEMP_0_PIN 3 //ANALOG NUMBERING +#define TEMP_1_PIN 2 //ANALOG NUMBERING +#define TEMP_2_PIN 1 //ANALOG NUMBERING +#define TEMP_BED_PIN 0 //ANALOG NUMBERING -#define BEEPER 36 +#define BEEPER 36 #define KILL_PIN -1 @@ -1082,14 +1081,14 @@ #endif //RA_LIGHTING -#endif /* Ra Board */ +#endif // ELEFU_3 /**************************************************************************************** * Gen6 pin assignment * ****************************************************************************************/ -#if MOTHERBOARD == 5 || MOTHERBOARD == 51 +#if MB(GEN6) || MB(GEN6_DELUXE) #define KNOWN_BOARD 1 #ifndef __AVR_ATmega644P__ @@ -1128,7 +1127,7 @@ #define HEATER_0_PIN 14 //changed @ rkoeppl 20110410 #define HEATER_1_PIN -1 #define HEATER_2_PIN -1 - #if MOTHERBOARD == 5 + #if MB(GEN6) #define HEATER_BED_PIN -1 //changed @ rkoeppl 20110410 #define TEMP_BED_PIN -1 //changed @ rkoeppl 20110410 #else @@ -1149,32 +1148,32 @@ #define TX_ENABLE_PIN 12 #define RX_ENABLE_PIN 13 - -#endif +#endif // GEN6 || GEN6_DELUXE /**************************************************************************************** * Sanguinololu pin assignment * ****************************************************************************************/ -#if MOTHERBOARD == 64 +#if MB(STB_11) #define STB #endif -#if MOTHERBOARD == 63 || MOTHERBOARD == 66 +#if MB(MELZI) || MB(MELZI_1284) #define MELZI #endif -#if MOTHERBOARD == 65 +#if MB(AZTEEG_X1) #define AZTEEG_X1 #endif -#if MOTHERBOARD == 62 || MOTHERBOARD == 63 || MOTHERBOARD == 64 || MOTHERBOARD == 65 || MOTHERBOARD == 66 +#if MB(SANGUINOLOLU_12) || MB(MELZI) || MB(STB_11) || MB(AZTEEG_X1) || MB(MELZI_1284) #undef MOTHERBOARD -#define MOTHERBOARD 6 +#define MOTHERBOARD BOARD_SANGUINOLOLU_11 #define SANGUINOLOLU_V_1_2 #if defined(__AVR_ATmega1284P__) - #define LARGE_FLASH true + #define LARGE_FLASH true #endif #endif -#if MOTHERBOARD == 6 + +#if MB(SANGUINOLOLU_11) #define KNOWN_BOARD 1 #ifndef __AVR_ATmega644P__ #ifndef __AVR_ATmega1284P__ @@ -1211,7 +1210,7 @@ #ifdef STB #define FAN_PIN 4 - // Uncomment this if you have the first generation (V1.10) of STBs board + // Uncomment this if you have the first generation (V1.10) of STBs board #define LCD_PIN_BL 17 // LCD backlight LED #endif @@ -1322,7 +1321,7 @@ // Pins for DOGM SPI LCD Support #define DOGLCD_A0 30 #define DOGLCD_CS 17 - #define LCD_PIN_BL 28 // backlight LED on PA3 + #define LCD_PIN_BL 28 // backlight LED on PA3 // GLCD features #define LCD_CONTRAST 1 // Uncomment screen orientation @@ -1338,15 +1337,16 @@ #define SDCARDDETECT -1 #endif //Makrpanel -#endif +#endif // SANGUINOLOLU_11 -#if MOTHERBOARD == 7 -#define KNOWN_BOARD /***************************************************************** * Ultimaker pin assignment ******************************************************************/ +#if MB(ULTIMAKER) +#define KNOWN_BOARD + #ifndef __AVR_ATmega1280__ #ifndef __AVR_ATmega2560__ #error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu. @@ -1442,9 +1442,9 @@ #endif #endif //ULTRA_LCD -#endif +#endif // ULTIMAKER -#if MOTHERBOARD == 71 +#if MB(ULTIMAKER_OLD) #define KNOWN_BOARD /***************************************************************** * Ultimaker pin assignment (Old electronics) @@ -1511,9 +1511,9 @@ #define LCD_PINS_D6 32 #define LCD_PINS_D7 30 -#endif +#endif // ULTIMAKER_OLD -#if MOTHERBOARD == 72 +#if MB(ULTIMAIN_2) #define KNOWN_BOARD /***************************************************************** * Ultiboard v2.0 pin assignment @@ -1596,13 +1596,13 @@ #define SDCARDDETECT 39 -#endif//MOTHERBOARD == 72 +#endif // ULTIMAIN_2 /**************************************************************************************** * RUMBA pin assignment * ****************************************************************************************/ -#if MOTHERBOARD == 80 +#if MB(RUMBA) #define KNOWN_BOARD 1 #ifndef __AVR_ATmega2560__ @@ -1712,7 +1712,7 @@ #define BTN_EN2 12 #define BTN_ENC 43 -#endif //MOTHERBOARD==80 +#endif // RUMBA /**************************************************************************************** @@ -1721,7 +1721,7 @@ http://www.pjrc.com/teensy/teensyduino.html * See http://reprap.org/wiki/Printrboard for more info ****************************************************************************************/ -#if MOTHERBOARD == 8 || MOTHERBOARD == 81 +#if MB(TEENSYLU) || MB(PRINTRBOARD) #define KNOWN_BOARD 1 #define AT90USB 1286 // Disable MarlinSerial etc. @@ -1759,7 +1759,7 @@ // You may need to change FAN_PIN to 16 because Marlin isn't using fastio.h // for the fan and Teensyduino uses a different pin mapping. -#if MOTHERBOARD == 8 // Teensylu +#if MB(TEENSYLU) // Teensylu #define X_STOP_PIN 13 #define Y_STOP_PIN 14 #define Z_STOP_PIN 15 @@ -1793,14 +1793,14 @@ #define MOSI_PIN 10 #endif -#endif // MOTHERBOARD == 8 (Teensylu) or 81 (Printrboard) +#endif // TEENSYLU || PRINTRBOARD /**************************************************************************************** * Brainwave 1.0 pin assignments (AT90USB646) * Requires hardware bundle for Arduino: https://github.com/unrepentantgeek/brainwave-arduino ****************************************************************************************/ -#if MOTHERBOARD == 82 +#if MB(BRAINWAVE) #define KNOWN_BOARD 1 #define AT90USB 646 // Disable MarlinSerial etc. @@ -1856,7 +1856,7 @@ #define MOSI_PIN 10 #endif -#endif // MOTHERBOARD == 82 (Brainwave) +#endif // BRAINWAVE // // SAV Mk-I @@ -1867,7 +1867,7 @@ http://www.pjrc.com/teensy/teensyduino.html RepRap Clone Wars project board. ****************************************************************************************/ -#if MOTHERBOARD == 83 // SAV Mk-I +#if MB(SAV_MKI) // SAV Mk-I #define KNOWN_BOARD 1 #define AT90USB 1286 // Disable MarlinSerial etc. @@ -1941,7 +1941,7 @@ #define SR_DATA_PIN 0 #define SR_CLK_PIN 1 -#endif // MOTHERBOARD == 83 +#endif // SAV_MKI /**************************************************************************************** * Teensy++ 2.0 Breadboard pin assignments (AT90USB1286) @@ -1951,7 +1951,7 @@ * CLI build: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make * ****************************************************************************************/ -#if MOTHERBOARD == 84 +#if MB(TEENSY2) #define KNOWN_BOARD 1 #define AT90USB 1286 // Disable MarlinSerial etc. @@ -2036,7 +2036,7 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #define TEMP_2_PIN -1 #define SDPOWER -1 -#define SDCARDDETECT -1 +#define SDCARDDETECT -1 #define SDSS 20 // 8 #define LED_PIN 6 #define PS_ON_PIN 27 @@ -2062,15 +2062,15 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #define BTN_ENC 40 #endif -#endif // MOTHERBOARD == 84 (Teensy++2.0 Breadboard) +#endif // TEENSY2 /**************************************************************************************** * Gen3+ pin assignment * ****************************************************************************************/ -#if MOTHERBOARD == 9 -#define MOTHERBOARD 6 /*TODO: Figure out, Why is this done?*/ +#if MB(GEN3_PLUS) +#define MOTHERBOARD BOARD_SANGUINOLOLU_11 /*TODO: Figure out, Why is this done?*/ #define KNOWN_BOARD 1 #ifndef __AVR_ATmega644P__ #ifndef __AVR_ATmega1284P__ @@ -2116,13 +2116,13 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #define SDSS 4 #define HEATER_2_PIN -1 -#endif +#endif // GEN3_PLUS /**************************************************************************************** * Gen3 Monolithic Electronics * ****************************************************************************************/ -#if MOTHERBOARD == 22 +#if MB(GEN3_MONOLITHIC) #define KNOWN_BOARD 1 #ifndef __AVR_ATmega644P__ @@ -2170,12 +2170,12 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #define TEMP_BED_PIN -1 -#define SDSS -1 +#define SDSS -1 #define SDPOWER -1 #define LED_PIN -1 //pin for controlling the PSU. -#define PS_ON_PIN 14 //Alex, Do this work on the card? +#define PS_ON_PIN 14 //Alex, Do this work on the card? //Alex extras from Gen3+ #define KILL_PIN -1 @@ -2183,7 +2183,7 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #define TEMP_2_PIN -1 #define HEATER_2_PIN -1 -#endif +#endif // GEN3_MONOLITHIC /**************************************************************************************** * Open Motion controller with enable based extruders @@ -2214,7 +2214,7 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a * +--------+ * ****************************************************************************************/ -#if MOTHERBOARD == 90 //Alpha OMCA board +#if MB(OMCA_A) //Alpha OMCA board #define KNOWN_BOARD 1 #ifndef __AVR_ATmega644__ @@ -2266,9 +2266,9 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #define TEMP_BED_PIN -1 // 1,2 or I2C /* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */ -#endif +#endif // OMCA_A -#if MOTHERBOARD == 91 // Final OMCA board -- REF http://sanguino.cc/hardware +#if MB(OMCA) // Final OMCA board -- REF http://sanguino.cc/hardware #define KNOWN_BOARD 1 #if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) @@ -2332,14 +2332,13 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #define I2C_SCL 16 #define I2C_SDA 17 -#endif +#endif // OMCA -#if MOTHERBOARD == 301 -#define KNOWN_BOARD /***************************************************************** * Rambo Pin Assignments ******************************************************************/ - +#if MB(RAMBO) +#define KNOWN_BOARD #ifndef __AVR_ATmega2560__ #error Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu. #endif @@ -2478,13 +2477,13 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #define FILWIDTH_PIN 3 #endif //FILAMENT_SENSOR -#endif +#endif // RAMBO /**************************************************************************************** * MegaTronics * ****************************************************************************************/ -#if MOTHERBOARD == 70 +#if MB(MEGATRONICS) #define KNOWN_BOARD 1 @@ -2570,7 +2569,7 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #define BLEN_B 1 #define BLEN_A 0 - #define SDCARDDETECT -1 // Ramps does not use this port + #define SDCARDDETECT -1 // Ramps does not use this port //encoder rotation values #define encrot0 0 @@ -2580,13 +2579,13 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #endif #endif //ULTRA_LCD -#endif +#endif // MEGATRONICS /**************************************************************************************** * MegaTronics v2.0 * ****************************************************************************************/ -#if MOTHERBOARD == 701 +#if MB(MEGATRONICS_2) #define KNOWN_BOARD 1 @@ -2682,7 +2681,7 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #define BLEN_B 1 #define BLEN_A 0 - #define SDCARDDETECT -1 // Megatronics does not use this port + #define SDCARDDETECT -1 // Megatronics does not use this port //encoder rotation values #define encrot0 0 @@ -2690,14 +2689,14 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #define encrot2 3 #define encrot3 1 -#endif +#endif // MEGATRONICS_2 /**************************************************************************************** * Minitronics v1.0 * ****************************************************************************************/ -#if MOTHERBOARD == 702 +#if MB(MEGATRONICS_1) #define KNOWN_BOARD 1 @@ -2778,7 +2777,7 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #define BLEN_B 1 #define BLEN_A 0 - #define SDCARDDETECT -1 // Megatronics does not use this port + #define SDCARDDETECT -1 // Megatronics does not use this port //encoder rotation values #define encrot0 0 @@ -2786,13 +2785,13 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #define encrot2 3 #define encrot3 1 -#endif +#endif // MEGATRONICS_1 /**************************************************************************************** * Cheaptronic v1.0 * ****************************************************************************************/ -#if MOTHERBOARD == 2 +#if MB(CHEAPTRONIC) #define KNOWN_BOARD 1 #ifndef __AVR_ATmega2560__ @@ -2887,7 +2886,7 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a #define encrot2 3 #define encrot3 1 -#endif +#endif // CHEAPTRONIC @@ -2954,5 +2953,5 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a HEATER_BED_PIN, FAN_PIN, \ _E0_PINS _E1_PINS _E2_PINS \ analogInputToDigitalPin(TEMP_0_PIN), analogInputToDigitalPin(TEMP_1_PIN), analogInputToDigitalPin(TEMP_2_PIN), analogInputToDigitalPin(TEMP_BED_PIN) } -#endif +#endif //__PINS_H diff --git a/Marlin/temperature.cpp b/Marlin/temperature.cpp index af5d8c130d..5dc55df6e9 100644 --- a/Marlin/temperature.cpp +++ b/Marlin/temperature.cpp @@ -768,7 +768,7 @@ return(filament_width_nominal/temp*100); void tp_init() { -#if (MOTHERBOARD == 80) && ((TEMP_SENSOR_0==-1)||(TEMP_SENSOR_1==-1)||(TEMP_SENSOR_2==-1)||(TEMP_SENSOR_BED==-1)) +#if MB(RUMBA) && ((TEMP_SENSOR_0==-1)||(TEMP_SENSOR_1==-1)||(TEMP_SENSOR_2==-1)||(TEMP_SENSOR_BED==-1)) //disable RUMBA JTAG in case the thermocouple extension is plugged on top of JTAG connector MCUCR=(1<