Cleanup temperature code

- Get rid of unused temp states in the ISR, resulting in more frequent temperature reading with fewer sensors - Shrink code slightly in min/max testing
10 years ago · 6bdee87be3
parent f65f61fa72
commit 6bdee87be3
1 changed files with 132 additions and 83 deletions
--- a/Marlin/temperature.cpp
+++ b/Marlin/temperature.cpp
@ -1240,16 +1240,26 @@ void disable_heater() {
 enum TempState {
  PrepareTemp_0,
  MeasureTemp_0,
-  PrepareTemp_BED,
-  MeasureTemp_BED,
-  PrepareTemp_1,
-  MeasureTemp_1,
-  PrepareTemp_2,
-  MeasureTemp_2,
-  PrepareTemp_3,
-  MeasureTemp_3,
-  Prepare_FILWIDTH,
-  Measure_FILWIDTH,
+  #if HAS_TEMP_BED
+    PrepareTemp_BED,
+    MeasureTemp_BED,
+  #endif
+  #if HAS_TEMP_1
+    PrepareTemp_1,
+    MeasureTemp_1,
+  #endif
+  #if HAS_TEMP_2
+    PrepareTemp_2,
+    MeasureTemp_2,
+  #endif
+  #if HAS_TEMP_3
+    PrepareTemp_3,
+    MeasureTemp_3,
+  #endif
+  #if HAS_FILAMENT_SENSOR
+    Prepare_FILWIDTH,
+    Measure_FILWIDTH,
+  #endif
  StartupDelay // Startup, delay initial temp reading a tiny bit so the hardware can settle
 };

@ -1473,78 +1483,124 @@ ISR(TIMER0_COMPB_vect) {
      #if HAS_TEMP_0
        raw_temp_value[0] += ADC;
      #endif
-      temp_state = PrepareTemp_BED;
+      temp_state =
+        #if HAS_TEMP_BED
+          PrepareTemp_BED
+        #elif HAS_TEMP_1
+          PrepareTemp_1
+        #elif HAS_TEMP_2
+          PrepareTemp_2
+        #elif HAS_TEMP_3
+          PrepareTemp_3
+        #elif HAS_FILAMENT_SENSOR
+          Prepare_FILWIDTH
+        #else
+          PrepareTemp_0
+        #endif
+      ;
      break;
-    case PrepareTemp_BED:
-      #if HAS_TEMP_BED
+
+    #if HAS_TEMP_BED
+      case PrepareTemp_BED:
        START_ADC(TEMP_BED_PIN);
-      #endif
-      lcd_buttons_update();
-      temp_state = MeasureTemp_BED;
-      break;
-    case MeasureTemp_BED:
-      #if HAS_TEMP_BED
+        lcd_buttons_update();
+        temp_state = MeasureTemp_BED;
+        break;
+      case MeasureTemp_BED:
        raw_temp_bed_value += ADC;
-      #endif
-      temp_state = PrepareTemp_1;
-      break;
-    case PrepareTemp_1:
-      #if HAS_TEMP_1
+        temp_state =
+          #if HAS_TEMP_1
+            PrepareTemp_1
+          #elif HAS_TEMP_2
+            PrepareTemp_2
+          #elif HAS_TEMP_3
+            PrepareTemp_3
+          #elif HAS_FILAMENT_SENSOR
+            Prepare_FILWIDTH
+          #else
+            PrepareTemp_0
+          #endif
+        ;
+        break;
+    #endif
+
+    #if HAS_TEMP_1
+      case PrepareTemp_1:
        START_ADC(TEMP_1_PIN);
-      #endif
-      lcd_buttons_update();
-      temp_state = MeasureTemp_1;
-      break;
-    case MeasureTemp_1:
-      #if HAS_TEMP_1
+        lcd_buttons_update();
+        temp_state = MeasureTemp_1;
+        break;
+      case MeasureTemp_1:
        raw_temp_value[1] += ADC;
-      #endif
-      temp_state = PrepareTemp_2;
-      break;
-    case PrepareTemp_2:
-      #if HAS_TEMP_2
+        temp_state =
+          #if HAS_TEMP_2
+            PrepareTemp_2
+          #elif HAS_TEMP_3
+            PrepareTemp_3
+          #elif HAS_FILAMENT_SENSOR
+            Prepare_FILWIDTH
+          #else
+            PrepareTemp_0
+          #endif
+        ;
+        break;
+    #endif
+
+    #if HAS_TEMP_2
+      case PrepareTemp_2:
        START_ADC(TEMP_2_PIN);
-      #endif
-      lcd_buttons_update();
-      temp_state = MeasureTemp_2;
-      break;
-    case MeasureTemp_2:
-      #if HAS_TEMP_2
+        lcd_buttons_update();
+        temp_state = MeasureTemp_2;
+        break;
+      case MeasureTemp_2:
        raw_temp_value[2] += ADC;
-      #endif
-      temp_state = PrepareTemp_3;
-      break;
-    case PrepareTemp_3:
-      #if HAS_TEMP_3
+        temp_state =
+          #if HAS_TEMP_3
+            PrepareTemp_3
+          #elif HAS_FILAMENT_SENSOR
+            Prepare_FILWIDTH
+          #else
+            PrepareTemp_0
+          #endif
+        ;
+        break;
+    #endif
+
+    #if HAS_TEMP_3
+      case PrepareTemp_3:
        START_ADC(TEMP_3_PIN);
-      #endif
-      lcd_buttons_update();
-      temp_state = MeasureTemp_3;
-      break;
-    case MeasureTemp_3:
-      #if HAS_TEMP_3
+        lcd_buttons_update();
+        temp_state = MeasureTemp_3;
+        break;
+      case MeasureTemp_3:
        raw_temp_value[3] += ADC;
-      #endif
-      temp_state = Prepare_FILWIDTH;
-      break;
-    case Prepare_FILWIDTH:
-      #if HAS_FILAMENT_SENSOR
+        temp_state =
+          #if HAS_FILAMENT_SENSOR
+            Prepare_FILWIDTH
+          #else
+            PrepareTemp_0
+          #endif
+        ;
+        break;
+    #endif
+
+    #if HAS_FILAMENT_SENSOR
+      case Prepare_FILWIDTH:
        START_ADC(FILWIDTH_PIN);
-      #endif
-      lcd_buttons_update();
-      temp_state = Measure_FILWIDTH;
-      break;
-    case Measure_FILWIDTH:
-      #if HAS_FILAMENT_SENSOR
+        lcd_buttons_update();
+        temp_state = Measure_FILWIDTH;
+        break;
+      case Measure_FILWIDTH:
        // raw_filwidth_value += ADC;  //remove to use an IIR filter approach
        if (ADC > 102) { //check that ADC is reading a voltage > 0.5 volts, otherwise don't take in the data.
          raw_filwidth_value -= (raw_filwidth_value>>7);  //multiply raw_filwidth_value by 127/128
          raw_filwidth_value += ((unsigned long)ADC<<7);  //add new ADC reading
        }
-      #endif
-      temp_state = PrepareTemp_0;
-      temp_count++;
-      break;
+        temp_state = PrepareTemp_0;
+        temp_count++;
+        break;
+    #endif
+
    case StartupDelay:
      temp_state = PrepareTemp_0;
      break;
@ -1554,7 +1610,7 @@ ISR(TIMER0_COMPB_vect) {
    //   SERIAL_ERRORLNPGM("Temp measurement error!");
    //   break;
  } // switch(temp_state)
-    
+
  if (temp_count >= OVERSAMPLENR) { // 10 * 16 * 1/(16000000/64/256)  = 164ms.
    if (!temp_meas_ready) { //Only update the raw values if they have been read. Else we could be updating them during reading.
      #ifndef HEATER_0_USES_MAX6675
@ -1579,7 +1635,7 @@ ISR(TIMER0_COMPB_vect) {
    #if HAS_FILAMENT_SENSOR
      current_raw_filwidth = raw_filwidth_value >> 10;  // Divide to get to 0-16384 range since we used 1/128 IIR filter approach
    #endif
-    
+
    temp_meas_ready = true;
    temp_count = 0;
    for (int i = 0; i < EXTRUDERS; i++) raw_temp_value[i] = 0;
@ -1587,44 +1643,39 @@ ISR(TIMER0_COMPB_vect) {

    #if HEATER_0_RAW_LO_TEMP > HEATER_0_RAW_HI_TEMP
      #define GE0 <=
-      #define LE0 >=
    #else
      #define GE0 >=
-      #define LE0 <=
    #endif
    if (current_temperature_raw[0] GE0 maxttemp_raw[0]) max_temp_error(0);
-    if (current_temperature_raw[0] LE0 minttemp_raw[0]) min_temp_error(0);
+    if (minttemp_raw[0] GE0 current_temperature_raw[0]) min_temp_error(0);

    #if EXTRUDERS > 1
      #if HEATER_1_RAW_LO_TEMP > HEATER_1_RAW_HI_TEMP
        #define GE1 <=
-        #define LE1 >=
      #else
        #define GE1 >=
-        #define LE1 <=
      #endif
      if (current_temperature_raw[1] GE1 maxttemp_raw[1]) max_temp_error(1);
-      if (current_temperature_raw[1] LE1 minttemp_raw[1]) min_temp_error(1);
+      if (minttemp_raw[1] GE0 current_temperature_raw[1]) min_temp_error(1);
+
      #if EXTRUDERS > 2
        #if HEATER_2_RAW_LO_TEMP > HEATER_2_RAW_HI_TEMP
          #define GE2 <=
-          #define LE2 >=
        #else
          #define GE2 >=
-          #define LE2 <=
        #endif
        if (current_temperature_raw[2] GE2 maxttemp_raw[2]) max_temp_error(2);
-        if (current_temperature_raw[2] LE2 minttemp_raw[2]) min_temp_error(2);
+        if (minttemp_raw[2] GE0 current_temperature_raw[2]) min_temp_error(2);
+
        #if EXTRUDERS > 3
          #if HEATER_3_RAW_LO_TEMP > HEATER_3_RAW_HI_TEMP
            #define GE3 <=
-            #define LE3 >=
          #else
            #define GE3 >=
-            #define LE3 <=
          #endif
          if (current_temperature_raw[3] GE3 maxttemp_raw[3]) max_temp_error(3);
-          if (current_temperature_raw[3] LE3 minttemp_raw[3]) min_temp_error(3);
+          if (minttemp_raw[3] GE0 current_temperature_raw[3]) min_temp_error(3);
+
        #endif // EXTRUDERS > 3
      #endif // EXTRUDERS > 2
    #endif // EXTRUDERS > 1
@ -1632,10 +1683,8 @@ ISR(TIMER0_COMPB_vect) {
    #if defined(BED_MAXTEMP) && (TEMP_SENSOR_BED != 0)
      #if HEATER_BED_RAW_LO_TEMP > HEATER_BED_RAW_HI_TEMP
        #define GEBED <=
-        #define LEBED >=
      #else
        #define GEBED >=
-        #define LEBED <=
      #endif
      if (current_temperature_bed_raw GEBED bed_maxttemp_raw) {
        target_temperature_bed = 0;