Fix up tests, warnings

Marlin/src/gcode/calibrate/M48.cpp

@@ -192,8 +192,8 @@ void GcodeSuite::M48() {
           // Choose the next position as an offset to chosen test position
           const xy_pos_t noz_pos = test_position - probe.offset_xy;
           xy_pos_t next_pos = {
-            noz_pos.x + cos(RADIANS(angle)) * radius,
+            noz_pos.x + float(cos(RADIANS(angle))) * radius,
-            noz_pos.y + sin(RADIANS(angle)) * radius
+            noz_pos.y + float(sin(RADIANS(angle))) * radius
           };
 
           #if ENABLED(DELTA)

Marlin/src/lcd/extui/ui_api.cpp

@@ -705,7 +705,7 @@ namespace ExtUI {
 
       #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
         // Make it so babystepping in Z adjusts the Z probe offset.
-        if (axis == Z && TERN1(HAS_MULTI_EXTRUDER, linked_nozzles || active_extruder == 0))
+        if (axis == Z && TERN1(HAS_MULTI_EXTRUDER, (linked_nozzles || active_extruder == 0)))
           probe.offset.z += mm;
       #endif
 

buildroot/tests/teensy41-tests

@@ -19,14 +19,15 @@ opt_set EXTRUDERS 2
 opt_set TEMP_SENSOR_0 1
 opt_set TEMP_SENSOR_1 5
 opt_set TEMP_SENSOR_BED 1
-opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER LCD_INFO_MENU SDSUPPORT SDCARD_SORT_ALPHA \
+opt_enable EXTENSIBLE_UI LCD_INFO_MENU SDSUPPORT SDCARD_SORT_ALPHA \
-           FILAMENT_WIDTH_SENSOR FILAMENT_LCD_DISPLAY CALIBRATION_GCODE BAUD_RATE_GCODE \
+           FILAMENT_LCD_DISPLAY CALIBRATION_GCODE BAUD_RATE_GCODE \
            FIX_MOUNTED_PROBE Z_SAFE_HOMING AUTO_BED_LEVELING_BILINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
-           BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET BABYSTEP_ZPROBE_GFX_OVERLAY \
+           BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET \
-           PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT M100_FREE_MEMORY_WATCHER \
+           PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \
            ADVANCED_PAUSE_FEATURE ARC_SUPPORT BEZIER_CURVE_SUPPORT EXPERIMENTAL_I2CBUS EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES PARK_HEAD_ON_PAUSE \
            PHOTO_GCODE PHOTO_POSITION PHOTO_SWITCH_POSITION PHOTO_SWITCH_MS PHOTO_DELAY_MS PHOTO_RETRACT_MM \
            HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT
+opt_add EXTUI_EXAMPLE
 opt_set I2C_SLAVE_ADDRESS 63
 opt_set GRID_MAX_POINTS_X 16
 exec_test $1 $2 "Teensy4.1 with many features"
@@ -62,7 +63,7 @@ restore_configs
 opt_set MOTHERBOARD BOARD_TEENSY41
 opt_set EXTRUDERS 2
 opt_set TEMP_SENSOR_1 1
-opt_enable MAGNETIC_PARKING_EXTRUDER ULTIMAKERCONTROLLER
+opt_enable MAGNETIC_PARKING_EXTRUDER
 exec_test $1 $2 "MAGNETIC_PARKING_EXTRUDER with LCD"
 
 #
@@ -70,7 +71,7 @@ exec_test $1 $2 "MAGNETIC_PARKING_EXTRUDER with LCD"
 #
 restore_configs
 opt_set MOTHERBOARD BOARD_TEENSY41
-opt_enable MIXING_EXTRUDER DIRECT_MIXING_IN_G1 GRADIENT_MIX GRADIENT_VTOOL REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+opt_enable MIXING_EXTRUDER DIRECT_MIXING_IN_G1 GRADIENT_MIX GRADIENT_VTOOL
 opt_set MIXING_STEPPERS 2
 exec_test $1 $2 "Mixing Extruder"
 

platformio.ini

@@ -207,7 +207,7 @@ HAS_L64XX               = Arduino-L6470@0.8.0
 NEOPIXEL_LED            = Adafruit NeoPixel@1.5.0
                           src_filter=+<src/feature/leds/neopixel.cpp>
 MAX6675_IS_MAX31865     = Adafruit MAX31865 library@~1.1.0
-HAS_GRAPHICAL_LCD       = U8glib-HAL@0.4.1
+HAS_GRAPHICAL_LCD       = U8glib-HAL@~0.4.1
                           src_filter=+<src/lcd/dogm>
 USES_LIQUIDCRYSTAL      = LiquidCrystal@1.5.0
 USES_LIQUIDTWI2         = LiquidTWI2@1.2.7