diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 680065eb69..d58c4d0427 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -932,7 +932,7 @@
  * Override with M92
  *                                      X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 500 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 79, 79, 400, 415 }
 
 /**
  * Default Max Feed Rate (mm/s)
@@ -1184,7 +1184,7 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { -20, 13, -1.49 }
+#define NOZZLE_TO_PROBE_OFFSET { -20, 14, -1.475 }
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
@@ -1388,7 +1388,7 @@
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
 #define X_MIN_POS -7
-#define Y_MIN_POS -2
+#define Y_MIN_POS -17
 #define Z_MIN_POS 0
 #define X_MAX_POS X_BED_SIZE
 #define Y_MAX_POS Y_BED_SIZE
@@ -1647,13 +1647,13 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
-  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+  #define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
 
   #define MESH_INSET 1              // Set Mesh bounds as an inset region of the bed
-  #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
+  #define GRID_MAX_POINTS_X 15      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
-  //#define UBL_HILBERT_CURVE       // Use Hilbert distribution for less travel when probing multiple points
+  #define UBL_HILBERT_CURVE       // Use Hilbert distribution for less travel when probing multiple points
 
   #define UBL_MESH_EDIT_MOVES_Z     // Sophisticated users prefer no movement of nozzle
   #define UBL_SAVE_ACTIVE_ON_M500   // Save the currently active mesh in the current slot on M500
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index b9b2798b65..2ace8d0c2f 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -1942,7 +1942,7 @@
  *
  * Warning: Does not respect endstops!
  */
-//#define BABYSTEPPING
+#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
   //#define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
   //#define BABYSTEP_WITHOUT_HOMING
@@ -1963,7 +1963,7 @@
     #endif
   #endif
 
-  //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
+  #define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
 
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
@@ -2489,7 +2489,7 @@
                                                   // This short retract is done immediately, before parking the nozzle.
   #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     10  // (mm/s) Unload filament feedrate. This can be pretty fast.
   #define FILAMENT_CHANGE_UNLOAD_ACCEL        25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_UNLOAD_LENGTH      100  // (mm) The length of filament for a complete unload.
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH       95  // (mm) The length of filament for a complete unload.
                                                   //   For Bowden, the full length of the tube and nozzle.
                                                   //   For direct drive, the full length of the nozzle.
                                                   //   Set to 0 for manual unloading.