diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 27fbf0d85e..759fa7b18d 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/Marlin/src/gcode/motion/G2_G3.cpp b/Marlin/src/gcode/motion/G2_G3.cpp index 6fecbdc0cc..e274b6a5cf 100644 --- a/Marlin/src/gcode/motion/G2_G3.cpp +++ b/Marlin/src/gcode/motion/G2_G3.cpp @@ -103,7 +103,15 @@ void plan_arc( mm_of_travel = linear_travel ? HYPOT(flat_mm, linear_travel) : ABS(flat_mm); if (mm_of_travel < 0.001f) return; - uint16_t segments = FLOOR(mm_of_travel / (MM_PER_ARC_SEGMENT)); + const feedRate_t scaled_fr_mm_s = MMS_SCALED(feedrate_mm_s); + + #ifdef ARC_SEGMENTS_PER_SEC + float seg_length = scaled_fr_mm_s * _RECIP(ARC_SEGMENTS_PER_SEC); + NOLESS(seg_length, MM_PER_ARC_SEGMENT); + #else + constexpr float seg_length = MM_PER_ARC_SEGMENT; + #endif + uint16_t segments = FLOOR(mm_of_travel / seg_length); NOLESS(segments, min_segments); /** @@ -146,10 +154,9 @@ void plan_arc( // Initialize the extruder axis raw.e = current_position.e; - const feedRate_t scaled_fr_mm_s = MMS_SCALED(feedrate_mm_s); #if ENABLED(SCARA_FEEDRATE_SCALING) - const float inv_duration = scaled_fr_mm_s / MM_PER_ARC_SEGMENT; + const float inv_duration = scaled_fr_mm_s / seg_length; #endif millis_t next_idle_ms = millis() + 200UL; @@ -206,7 +213,7 @@ void plan_arc( planner.apply_leveling(raw); #endif - if (!planner.buffer_line(raw, scaled_fr_mm_s, active_extruder, MM_PER_ARC_SEGMENT + if (!planner.buffer_line(raw, scaled_fr_mm_s, active_extruder, seg_length #if ENABLED(SCARA_FEEDRATE_SCALING) , inv_duration #endif @@ -226,7 +233,7 @@ void plan_arc( planner.apply_leveling(raw); #endif - planner.buffer_line(raw, scaled_fr_mm_s, active_extruder, MM_PER_ARC_SEGMENT + planner.buffer_line(raw, scaled_fr_mm_s, active_extruder, seg_length #if ENABLED(SCARA_FEEDRATE_SCALING) , inv_duration #endif diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h index 27fbf0d85e..759fa7b18d 100644 --- a/config/default/Configuration_adv.h +++ b/config/default/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h index 8f5a984500..6399f17dde 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h index 073618ff44..517d3095b5 100644 --- a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h index edf4711c9e..ce085247f9 100644 --- a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h +++ b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h index d5cd2b0577..11e46102b5 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h +++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h index eed6927924..0b958bf319 100644 --- a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h +++ b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h index 492849a5b6..f2bb40f4d3 100644 --- a/config/examples/Alfawise/U20/Configuration_adv.h +++ b/config/examples/Alfawise/U20/Configuration_adv.h @@ -1530,9 +1530,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h index e7d1cc06fa..baccb7a376 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h +++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h index f3429d756c..2227e53b98 100644 --- a/config/examples/Anet/A2/Configuration_adv.h +++ b/config/examples/Anet/A2/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h index f3429d756c..2227e53b98 100644 --- a/config/examples/Anet/A2plus/Configuration_adv.h +++ b/config/examples/Anet/A2plus/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h index 297f968321..795e78f82d 100644 --- a/config/examples/Anet/A6/Configuration_adv.h +++ b/config/examples/Anet/A6/Configuration_adv.h @@ -1529,9 +1529,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h index 3297703b1a..6c4eab7ac5 100644 --- a/config/examples/Anet/A8/Configuration_adv.h +++ b/config/examples/Anet/A8/Configuration_adv.h @@ -1529,9 +1529,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h index f765edb494..6cc26e5d25 100644 --- a/config/examples/Anet/A8plus/Configuration_adv.h +++ b/config/examples/Anet/A8plus/Configuration_adv.h @@ -1529,9 +1529,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Anet/E10/Configuration_adv.h b/config/examples/Anet/E10/Configuration_adv.h index 5eb24aa0a0..6c7abfd56b 100644 --- a/config/examples/Anet/E10/Configuration_adv.h +++ b/config/examples/Anet/E10/Configuration_adv.h @@ -1529,9 +1529,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Anet/E16/Configuration_adv.h b/config/examples/Anet/E16/Configuration_adv.h index 6bcac3b634..4d6cd81f72 100644 --- a/config/examples/Anet/E16/Configuration_adv.h +++ b/config/examples/Anet/E16/Configuration_adv.h @@ -1529,9 +1529,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h index 03d2d90424..b0986cdbef 100644 --- a/config/examples/AnyCubic/i3/Configuration_adv.h +++ b/config/examples/AnyCubic/i3/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h index 91d36066a9..b84accab8a 100644 --- a/config/examples/ArmEd/Configuration_adv.h +++ b/config/examples/ArmEd/Configuration_adv.h @@ -1533,9 +1533,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Artillery/Genius/Configuration_adv.h b/config/examples/Artillery/Genius/Configuration_adv.h index 3b2e37e74e..09d8773ed8 100755 --- a/config/examples/Artillery/Genius/Configuration_adv.h +++ b/config/examples/Artillery/Genius/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Artillery/Sidewinder X1/Configuration_adv.h b/config/examples/Artillery/Sidewinder X1/Configuration_adv.h index 3b2e37e74e..09d8773ed8 100755 --- a/config/examples/Artillery/Sidewinder X1/Configuration_adv.h +++ b/config/examples/Artillery/Sidewinder X1/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h index 06c52a5e7f..9345c411b3 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h index 9062f003b1..5a10f58572 100644 --- a/config/examples/BIBO/TouchX/default/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h index bc8b649b30..085bc95a69 100644 --- a/config/examples/BQ/Hephestos/Configuration_adv.h +++ b/config/examples/BQ/Hephestos/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h index 72524ed6c0..d45ed20180 100644 --- a/config/examples/BQ/Hephestos_2/Configuration_adv.h +++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h @@ -1537,9 +1537,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h index bc8b649b30..085bc95a69 100644 --- a/config/examples/BQ/WITBOX/Configuration_adv.h +++ b/config/examples/BQ/WITBOX/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h index cbca51c32c..1755d099a8 100644 --- a/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h +++ b/config/examples/BigTreeTech/SKR Mini E3 1.0/Configuration_adv.h @@ -1529,9 +1529,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h index 41d6453a25..e57e27d8ba 100644 --- a/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h +++ b/config/examples/BigTreeTech/SKR Mini E3 1.2/Configuration_adv.h @@ -1529,9 +1529,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h index 20fed00c18..8e3c3a1341 100644 --- a/config/examples/Cartesio/Configuration_adv.h +++ b/config/examples/Cartesio/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h index 05b7650076..4e934c5e48 100644 --- a/config/examples/Creality/CR-10/Configuration_adv.h +++ b/config/examples/Creality/CR-10/Configuration_adv.h @@ -1529,9 +1529,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h index b99931263f..bcba213934 100644 --- a/config/examples/Creality/CR-10S/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h index f67c0578e0..dfa798dff1 100644 --- a/config/examples/Creality/CR-10_5S/Configuration_adv.h +++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Creality/CR-10mini/Configuration_adv.h b/config/examples/Creality/CR-10mini/Configuration_adv.h index b3078a3c88..2096eb32ac 100644 --- a/config/examples/Creality/CR-10mini/Configuration_adv.h +++ b/config/examples/Creality/CR-10mini/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Creality/CR-20 Pro/Configuration_adv.h b/config/examples/Creality/CR-20 Pro/Configuration_adv.h index 92deade753..238e63fcf9 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration_adv.h +++ b/config/examples/Creality/CR-20 Pro/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Creality/CR-20/Configuration_adv.h b/config/examples/Creality/CR-20/Configuration_adv.h index 9c2d7e9c41..0abf737f9e 100644 --- a/config/examples/Creality/CR-20/Configuration_adv.h +++ b/config/examples/Creality/CR-20/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h index 19a0a27518..a45574b98e 100644 --- a/config/examples/Creality/CR-8/Configuration_adv.h +++ b/config/examples/Creality/CR-8/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h index 63a49b2895..a1cf874043 100644 --- a/config/examples/Creality/Ender-2/Configuration_adv.h +++ b/config/examples/Creality/Ender-2/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Creality/Ender-3/Configuration_adv.h b/config/examples/Creality/Ender-3/Configuration_adv.h index 6a8d0218bc..70e3fbc7de 100644 --- a/config/examples/Creality/Ender-3/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h index 7cf287f986..57d9845047 100644 --- a/config/examples/Creality/Ender-4/Configuration_adv.h +++ b/config/examples/Creality/Ender-4/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Creality/Ender-5 Pro/Configuration_adv.h b/config/examples/Creality/Ender-5 Pro/Configuration_adv.h index f1d1ac09bb..dbb37ae80f 100644 --- a/config/examples/Creality/Ender-5 Pro/Configuration_adv.h +++ b/config/examples/Creality/Ender-5 Pro/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Creality/Ender-5/Configuration_adv.h b/config/examples/Creality/Ender-5/Configuration_adv.h index 0ebdd83b58..2c5b611bf4 100644 --- a/config/examples/Creality/Ender-5/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h index 774cd6cd72..628c81dd6f 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h index eb76a0b60d..c2adaf353b 100644 --- a/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h +++ b/config/examples/EXP3D/Imprimante multifonction/Configuration_adv.h @@ -1529,11 +1529,12 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections - #define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles - #define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + #define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h index 11d386d0a8..1a34c950ab 100644 --- a/config/examples/Einstart-S/Configuration_adv.h +++ b/config/examples/Einstart-S/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/FYSETC/AIO_II/Configuration_adv.h b/config/examples/FYSETC/AIO_II/Configuration_adv.h index f9f738937d..f756125cf5 100644 --- a/config/examples/FYSETC/AIO_II/Configuration_adv.h +++ b/config/examples/FYSETC/AIO_II/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h index d0dfb609f5..9afd6ffb21 100644 --- a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h index d0dfb609f5..9afd6ffb21 100644 --- a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h index d0dfb609f5..9afd6ffb21 100644 --- a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h index d0dfb609f5..9afd6ffb21 100644 --- a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/FYSETC/F6_13/Configuration_adv.h b/config/examples/FYSETC/F6_13/Configuration_adv.h index bcddc512cd..bd353f3ed7 100644 --- a/config/examples/FYSETC/F6_13/Configuration_adv.h +++ b/config/examples/FYSETC/F6_13/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/FYSETC/S6/Configuration_adv.h b/config/examples/FYSETC/S6/Configuration_adv.h index 27fbf0d85e..759fa7b18d 100644 --- a/config/examples/FYSETC/S6/Configuration_adv.h +++ b/config/examples/FYSETC/S6/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Felix/DUAL/Configuration_adv.h b/config/examples/Felix/DUAL/Configuration_adv.h index af71111093..7db5639b22 100644 --- a/config/examples/Felix/DUAL/Configuration_adv.h +++ b/config/examples/Felix/DUAL/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Felix/Single/Configuration_adv.h b/config/examples/Felix/Single/Configuration_adv.h index af71111093..7db5639b22 100644 --- a/config/examples/Felix/Single/Configuration_adv.h +++ b/config/examples/Felix/Single/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h index b31419be85..668ec63891 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h +++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h @@ -1528,9 +1528,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h index bae7f04427..afdd236868 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h +++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h index 7121f6ac81..9d4f248bc8 100644 --- a/config/examples/Formbot/Raptor/Configuration_adv.h +++ b/config/examples/Formbot/Raptor/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h index 2dd6e53ec7..908b6964c6 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h @@ -1533,9 +1533,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h index 7fae4b7c82..1700414037 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h @@ -1533,9 +1533,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h index d905e7ba7b..f474427f74 100644 --- a/config/examples/Geeetech/A10/Configuration_adv.h +++ b/config/examples/Geeetech/A10/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Geeetech/A10D/Configuration_adv.h b/config/examples/Geeetech/A10D/Configuration_adv.h index e35bd19196..f45ba17361 100644 --- a/config/examples/Geeetech/A10D/Configuration_adv.h +++ b/config/examples/Geeetech/A10D/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h index 0ddeba6a1e..610e16ffd4 100644 --- a/config/examples/Geeetech/A10M/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Geeetech/A10T/Configuration_adv.h b/config/examples/Geeetech/A10T/Configuration_adv.h index 0ddeba6a1e..610e16ffd4 100644 --- a/config/examples/Geeetech/A10T/Configuration_adv.h +++ b/config/examples/Geeetech/A10T/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Geeetech/A20/Configuration_adv.h b/config/examples/Geeetech/A20/Configuration_adv.h index c64956697f..b3f9430053 100644 --- a/config/examples/Geeetech/A20/Configuration_adv.h +++ b/config/examples/Geeetech/A20/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h index c64956697f..b3f9430053 100644 --- a/config/examples/Geeetech/A20M/Configuration_adv.h +++ b/config/examples/Geeetech/A20M/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Geeetech/A20T/Configuration_adv.h b/config/examples/Geeetech/A20T/Configuration_adv.h index c64956697f..b3f9430053 100644 --- a/config/examples/Geeetech/A20T/Configuration_adv.h +++ b/config/examples/Geeetech/A20T/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Geeetech/A30/Configuration_adv.h b/config/examples/Geeetech/A30/Configuration_adv.h index 99e22b5d8b..52182562c8 100644 --- a/config/examples/Geeetech/A30/Configuration_adv.h +++ b/config/examples/Geeetech/A30/Configuration_adv.h @@ -1529,11 +1529,12 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections - #define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles - #define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + #define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. - unused by most slicers diff --git a/config/examples/Geeetech/D200/Configuration_adv.h b/config/examples/Geeetech/D200/Configuration_adv.h index 43f48d9df0..064e186690 100644 --- a/config/examples/Geeetech/D200/Configuration_adv.h +++ b/config/examples/Geeetech/D200/Configuration_adv.h @@ -1529,11 +1529,12 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections - #define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles - #define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + #define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. - unused by most slicers diff --git a/config/examples/Geeetech/E180/Configuration_adv.h b/config/examples/Geeetech/E180/Configuration_adv.h index 99e22b5d8b..52182562c8 100644 --- a/config/examples/Geeetech/E180/Configuration_adv.h +++ b/config/examples/Geeetech/E180/Configuration_adv.h @@ -1529,11 +1529,12 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections - #define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles - #define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + #define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. - unused by most slicers diff --git a/config/examples/Geeetech/M201/Configuration_adv.h b/config/examples/Geeetech/M201/Configuration_adv.h index 43f48d9df0..064e186690 100644 --- a/config/examples/Geeetech/M201/Configuration_adv.h +++ b/config/examples/Geeetech/M201/Configuration_adv.h @@ -1529,11 +1529,12 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections - #define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles - #define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + #define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. - unused by most slicers diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h index b24bcfd769..a82b3e42d1 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h +++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h @@ -1528,9 +1528,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h index 4728d2af49..59ddaf0590 100644 --- a/config/examples/Geeetech/PI3A PRO/Configuration_adv.h +++ b/config/examples/Geeetech/PI3A PRO/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h index d905e7ba7b..f474427f74 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h index d905e7ba7b..f474427f74 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/HMS434/Configuration_adv.h b/config/examples/HMS434/Configuration_adv.h index a146e69c2d..b64b01fb98 100644 --- a/config/examples/HMS434/Configuration_adv.h +++ b/config/examples/HMS434/Configuration_adv.h @@ -1521,9 +1521,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h index bd47a908d9..14a30a8ca8 100644 --- a/config/examples/Infitary/i3-M508/Configuration_adv.h +++ b/config/examples/Infitary/i3-M508/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h index 7941eca007..b10b8f4cb9 100644 --- a/config/examples/JGAurora/A1/Configuration_adv.h +++ b/config/examples/JGAurora/A1/Configuration_adv.h @@ -1534,9 +1534,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h index d6700d00f2..6195688699 100644 --- a/config/examples/JGAurora/A5/Configuration_adv.h +++ b/config/examples/JGAurora/A5/Configuration_adv.h @@ -1529,9 +1529,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h index 7941eca007..b10b8f4cb9 100644 --- a/config/examples/JGAurora/A5S/Configuration_adv.h +++ b/config/examples/JGAurora/A5S/Configuration_adv.h @@ -1534,9 +1534,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/JGAurora/Magic/Configuration_adv.h b/config/examples/JGAurora/Magic/Configuration_adv.h index 02b28a052a..962195dbe5 100644 --- a/config/examples/JGAurora/Magic/Configuration_adv.h +++ b/config/examples/JGAurora/Magic/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h b/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h index 41212bfaf0..392819f3bd 100644 --- a/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h +++ b/config/examples/MakerFarm/Pegasus_12/Configuration_adv.h @@ -1529,9 +1529,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h index 22319f3ebb..320e0b8354 100644 --- a/config/examples/MakerParts/Configuration_adv.h +++ b/config/examples/MakerParts/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h index 6c632fa27c..c4b70beb4f 100644 --- a/config/examples/Malyan/M150/Configuration_adv.h +++ b/config/examples/Malyan/M150/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h index d6ccfe88b5..0b5fecba56 100644 --- a/config/examples/Malyan/M200/Configuration_adv.h +++ b/config/examples/Malyan/M200/Configuration_adv.h @@ -1531,9 +1531,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h index 2688b44d2e..e8f9b0e422 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h +++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h index b6a6538806..6d712b7d6b 100644 --- a/config/examples/Mks/Robin/Configuration_adv.h +++ b/config/examples/Mks/Robin/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h index bc59e1a935..0510a2641b 100644 --- a/config/examples/Mks/Sbase/Configuration_adv.h +++ b/config/examples/Mks/Sbase/Configuration_adv.h @@ -1530,9 +1530,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Modix/Big60/Configuration_adv.h b/config/examples/Modix/Big60/Configuration_adv.h index 35494a41f3..e55b00f251 100644 --- a/config/examples/Modix/Big60/Configuration_adv.h +++ b/config/examples/Modix/Big60/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h index bcb251445d..f717c73606 100644 --- a/config/examples/RapideLite/RL200/Configuration_adv.h +++ b/config/examples/RapideLite/RL200/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Renkforce/RF100/Configuration_adv.h b/config/examples/Renkforce/RF100/Configuration_adv.h index 881c8b303d..4b05baa829 100644 --- a/config/examples/Renkforce/RF100/Configuration_adv.h +++ b/config/examples/Renkforce/RF100/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Renkforce/RF100XL/Configuration_adv.h b/config/examples/Renkforce/RF100XL/Configuration_adv.h index 881c8b303d..4b05baa829 100644 --- a/config/examples/Renkforce/RF100XL/Configuration_adv.h +++ b/config/examples/Renkforce/RF100XL/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Renkforce/RF100v2/Configuration_adv.h b/config/examples/Renkforce/RF100v2/Configuration_adv.h index 881c8b303d..4b05baa829 100644 --- a/config/examples/Renkforce/RF100v2/Configuration_adv.h +++ b/config/examples/Renkforce/RF100v2/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h index b9675b3634..4a2e9c4c37 100644 --- a/config/examples/RigidBot/Configuration_adv.h +++ b/config/examples/RigidBot/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/SCARA/MP_SCARA/Configuration_adv.h b/config/examples/SCARA/MP_SCARA/Configuration_adv.h index 47b319dc86..fa1e17fd6c 100644 --- a/config/examples/SCARA/MP_SCARA/Configuration_adv.h +++ b/config/examples/SCARA/MP_SCARA/Configuration_adv.h @@ -1396,9 +1396,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/SCARA/Morgan/Configuration_adv.h b/config/examples/SCARA/Morgan/Configuration_adv.h index d69476b520..e4258e31ba 100644 --- a/config/examples/SCARA/Morgan/Configuration_adv.h +++ b/config/examples/SCARA/Morgan/Configuration_adv.h @@ -1526,9 +1526,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h index 5457678ad4..109acf5959 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h index dd4eb94f4e..f115d1838f 100644 --- a/config/examples/Sanguinololu/Configuration_adv.h +++ b/config/examples/Sanguinololu/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h index 87a4ac4856..e5a2e53ffe 100644 --- a/config/examples/Tevo/Michelangelo/Configuration_adv.h +++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Tevo/Nereus/Configuration_adv.h b/config/examples/Tevo/Nereus/Configuration_adv.h index 7d2ea316a8..5fe6dc3abc 100755 --- a/config/examples/Tevo/Nereus/Configuration_adv.h +++ b/config/examples/Tevo/Nereus/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h index f3d1045aee..b4e94940b7 100755 --- a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h index 6ad36bc9e2..2a8a2c35b7 100755 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h @@ -1529,9 +1529,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h index 6ad36bc9e2..2a8a2c35b7 100755 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h @@ -1529,9 +1529,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h index cbde07da67..c95f590314 100644 --- a/config/examples/TheBorg/Configuration_adv.h +++ b/config/examples/TheBorg/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h index 7693247922..e3c2437bc1 100644 --- a/config/examples/TinyBoy2/Configuration_adv.h +++ b/config/examples/TinyBoy2/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h index 62658dd4e3..3bd8837912 100644 --- a/config/examples/Tronxy/X3A/Configuration_adv.h +++ b/config/examples/Tronxy/X3A/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h index 0e98cbc2c1..7228bc820f 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h +++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h index 1ca189266a..032728891e 100644 --- a/config/examples/UltiMachine/Archim1/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h index 99c860659f..2b06bfff48 100644 --- a/config/examples/UltiMachine/Archim2/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h index 04a2e49965..e16b29fc34 100644 --- a/config/examples/VORONDesign/Configuration_adv.h +++ b/config/examples/VORONDesign/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h index 19978fc652..458a688786 100644 --- a/config/examples/Velleman/K8200/Configuration_adv.h +++ b/config/examples/Velleman/K8200/Configuration_adv.h @@ -1542,9 +1542,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h index 14f56db3cd..dc088902dc 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h index 14f56db3cd..dc088902dc 100644 --- a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h index 127e0c20b8..e48e082562 100644 --- a/config/examples/WASP/PowerWASP/Configuration_adv.h +++ b/config/examples/WASP/PowerWASP/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h index 6f95b25cac..a7bb8fb0a5 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h index 0235859d3c..0e8327b6fe 100644 --- a/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h index 61d023dfca..669379547f 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h index 48c3ca0af4..4e67fb10c6 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h index 0e0002b3ab..cca52dfa9e 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h @@ -1530,9 +1530,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h index 2bafa9cd70..28feeaf024 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h index c37de68a3e..94e836e197 100644 --- a/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h +++ b/config/examples/delta/FLSUN/QQ-S/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h index 7e277f2a53..61a2ccff58 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h index 7e277f2a53..61a2ccff58 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h index 502533dc11..e9edf51a93 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h index f9f3a9082b..69ef82b638 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h index f0a442add6..7052b5cd4f 100644 --- a/config/examples/delta/MKS/SBASE/Configuration_adv.h +++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h index 10ce3ce224..1750b97d97 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h +++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h index 502533dc11..e9edf51a93 100644 --- a/config/examples/delta/generic/Configuration_adv.h +++ b/config/examples/delta/generic/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/delta/kossel_clear/Configuration_adv.h b/config/examples/delta/kossel_clear/Configuration_adv.h index 0316631df9..be889b5da0 100644 --- a/config/examples/delta/kossel_clear/Configuration_adv.h +++ b/config/examples/delta/kossel_clear/Configuration_adv.h @@ -1531,9 +1531,10 @@ // //#define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h index 502533dc11..e9edf51a93 100644 --- a/config/examples/delta/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/kossel_mini/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h index 5832d0c0a1..0331768465 100644 --- a/config/examples/delta/kossel_xl/Configuration_adv.h +++ b/config/examples/delta/kossel_xl/Configuration_adv.h @@ -1531,9 +1531,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h index dc7be02c67..2bbf5f65c9 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h +++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h index 6198346b22..0730c1dd8b 100644 --- a/config/examples/makibox/Configuration_adv.h +++ b/config/examples/makibox/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h index 9000e207f3..b041f94f83 100644 --- a/config/examples/tvrrug/Round2/Configuration_adv.h +++ b/config/examples/tvrrug/Round2/Configuration_adv.h @@ -1529,9 +1529,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h index 50a361af6a..0b51e66c14 100644 --- a/config/examples/wt150/Configuration_adv.h +++ b/config/examples/wt150/Configuration_adv.h @@ -1530,9 +1530,10 @@ // #define ARC_SUPPORT // Disable this feature to save ~3226 bytes #if ENABLED(ARC_SUPPORT) - #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment - #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle - #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + #define MM_PER_ARC_SEGMENT 1 // (mm) Length (or minimum length) of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + //#define ARC_SEGMENTS_PER_SEC 50 // Use feedrate to choose segment length (with MM_PER_ARC_SEGMENT as the minimum) + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes #endif