From 36a49eab1c33d732dad85660fca15de9eaa6b4ea Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Jo=C3=A3o=20Br=C3=A1zio?= Date: Thu, 14 Apr 2016 20:09:27 +0100 Subject: [PATCH] Improved the LCD and SD comments blocks in Configuration.h --- Marlin/Configuration.h | 301 ++++++++++++++++++++++++++++++----------- 1 file changed, 220 insertions(+), 81 deletions(-) diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 19d4710b1b..0c9e1bc947 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -714,7 +714,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l // @section extras +// // EEPROM +// // The microcontroller can store settings in the EEPROM, e.g. max velocity... // M500 - stores parameters in EEPROM // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). @@ -754,113 +756,250 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l #define ABS_PREHEAT_HPB_TEMP 110 #define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255 -//==============================LCD and SD support============================= +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= // @section lcd -// Define your display language below. Replace (en) with your language code and uncomment. -// en, pl, fr, de, es, ru, bg, it, pt, pt_utf8, pt-br, pt-br_utf8, fi, an, nl, ca, eu, kana, kana_utf8, cn, cz, test -// See also language.h +// +// MARLIN LANGUAGE +// +// Here you may choose the language used by Marlin on the LCD menus, the following +// list of languages are available: +// en, pl, fr, de, es, ru, bg, it, pt, pt_utf8, pt-br, pt-br_utf8, +// fi, an, nl, ca, eu, kana, kana_utf8, cn, cz, test +// #define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) -// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display. -// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset. +// +// LCD CHARSET +// +// Choose ONE of the following charset list, keep in mind that this selection is +// dependent on your physical hardware thus it has to match the type of Character +// based LCD you have. +// +// Note: This options is ignored for a full graphic display. +// +// To find out what type you have: +// - Compile and upload with language set to 'test' +// - Click to get the menu +// +// You'll see two typical lines from the upper half of the charset. +// // See also https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language - #define DISPLAY_CHARSET_HD44780_JAPAN // this is the most common hardware - //#define DISPLAY_CHARSET_HD44780_WESTERN - //#define DISPLAY_CHARSET_HD44780_CYRILLIC +// +#define DISPLAY_CHARSET_HD44780_JAPAN // this is the most common hardware +//#define DISPLAY_CHARSET_HD44780_WESTERN +//#define DISPLAY_CHARSET_HD44780_CYRILLIC -//#define ULTRA_LCD //general LCD support, also 16x2 -//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) -//#define SDSUPPORT // Enable SD Card Support in Hardware Console - // Changed behaviour! If you need SDSUPPORT uncomment it! -//#define SPI_SPEED SPI_HALF_SPEED // (also SPI_QUARTER_SPEED, SPI_EIGHTH_SPEED) Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -//#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication -//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder -//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking -//#define REVERSE_MENU_DIRECTION // When enabled CLOCKWISE moves UP in the LCD menu -//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store. -//#define ULTIPANEL //the UltiPanel as on Thingiverse -//#define SPEAKER // The sound device is a speaker - not a buzzer. A buzzer resonates with a fixed frequency. -//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click -//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click - // 0 to disable buzzer feedback. Test with M300 S P -// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) -// http://reprap.org/wiki/PanelOne +// +// LCD TYPE +// +// You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2, +// 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels +// (ST7565R family). +// +// IMPORTANT NOTE: You have to install Arduino's U8glib library for the Full +// Graphics Display to work ! - https://github.com/olikraus/U8glib_Arduino +// +//#define ULTRA_LCD // Character based +//#define DOGLCD // Full graphics display + +// +// SD CARD +// +// SD card support is now disabled by default, if you have [and want] SD support +// then you must uncomment the following directive. +// +//#define SDSUPPORT + +// +// SD CARD: SPI SPEED +// +// You may uncomment *one* of the following directives to use slower SPI transfer +// speeds, this is usually required if you're getting volume init errors. +// +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +// +// SD CARD: ENABLE CRC +// +// Use CRC checks and retries on the SD communication. +// +//#define SD_CHECK_AND_RETRY + +// +// ENCODER SETTINGS +// +// This option defines how many pulses a encoder should produce for a menu +// step to be produced, you should increase this value for highres encoders. +// +//#define ENCODER_PULSES_PER_STEP 1 +// +// +// This option defines how many steps are required for Marlin to move between +// next/prev menu items. +// +//#define ENCODER_STEPS_PER_MENU_ITEM 5 +// +// +// This option allows you to reverse the direction you have to turn the encoder +// to navigate up/down on the menus, by default CLOCKWISE rotation moves DOWN in +// the LCD menu, when active CLOCKWISE rotation will move UP in the LCD menu. +// +//#define REVERSE_MENU_DIRECTION +// +// +// If you have a speaker activate this directive to enable it. +// By default Marlin assumes your setup is buzzer based and no action is required. +// +//#define SPEAKER +// +// The duration and frequency the buzzer plays the UI feedback sound. +// You may define these directives with 0 (zero) if you want to disable all sound +// feedback from Marlin. +// +// Note: You may test the buzzing sound with the G-Code: +// M300 S P +// +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 +//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 + +// +// CONTROLLER TYPE: Standard +// +// Marlin supports a impressive variety of controllers, uncomment the directive +// which defines physical controller you're using. +// +// +// Activate this directive if you have an ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER +// +// +// Activate this directive if you have a ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL +// +// +// Activate this directive if you have a PanelOne from T3P3 +// (via RAMPS 1.4 AUX2/AUX3) - http://reprap.org/wiki/PanelOne +// //#define PANEL_ONE - -// The MaKr3d Makr-Panel with graphic controller and SD support -// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +// +// Activate this directive if you have a MaKr3d Makr-Panel with graphic +// controller and SD suppord - http://reprap.org/wiki/MaKr3d_MaKrPanel +// //#define MAKRPANEL - -// The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD -// http://panucatt.com -// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino +// +// +// Activate one of these directives if you have a Panucatt Devices Viki 2.0 or +// mini Viki with Graphic LCD - http://panucatt.com +// //#define VIKI2 //#define miniVIKI // This is a new controller currently under development. https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ // -// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino +// +// Activate this directive if you have an Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// //#define ELB_FULL_GRAPHIC_CONTROLLER -//#define SD_DETECT_INVERTED - -// The RepRapDiscount Smart Controller (white PCB) +// +// +// Activate this directive if you have a RepRapDiscount Smart Controller. // http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold in a white PCB. +// //#define REPRAP_DISCOUNT_SMART_CONTROLLER - -// The GADGETS3D G3D LCD/SD Controller (blue PCB) +// +// +// Activate this directive if you have a BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER +// +// +// Activate this directive if you have a GADGETS3D G3D LCD/SD Controller // http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold in a blue PCB. +// //#define G3D_PANEL - -// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB) +// +// +// Activate this directive if you have a RepRapDiscount FULL GRAPHIC Smart Controller // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller // -// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino -//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER - -// The RepRapWorld REPRAPWORLD_KEYPAD v1.1 -// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 -//#define REPRAPWORLD_KEYPAD -//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click - -// The Elefu RA Board Control Panel -// http://www.elefu.com/index.php?route=product/product&product_id=53 -// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C -//#define RA_CONTROL_PANEL - -// The MakerLab Mini Panel with graphic controller and SD support -// http://reprap.org/wiki/Mini_panel -//#define MINIPANEL - -/** - * I2C Panels - */ - -//#define LCD_I2C_SAINSMART_YWROBOT - -//#define LCM1602 // LCM1602 Adapter for 16x2 LCD - -// PANELOLU2 LCD with status LEDs, separate encoder and click inputs +// #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER +// +// +// Activate this directive if you have a MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +//#define MINIPANEL +// +// +// Activate this directive if you have a RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// +// +// Activate this directive if you have an Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL +//#define LCD_I2C_SAINSMART_YWROBOT +// +// +// Activate this directive if you have a LCM160 LCD adapter. +// +//#define LCM1602 +// +// +// Activate this directive if you have a PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). // -// This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 ) -// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory. -// (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file) -// Note: The PANELOLU2 encoder click input can either be directly connected to a pin -// (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). //#define LCD_I2C_PANELOLU2 - -// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs +// +// +// Activate this directive if you have a Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// //#define LCD_I2C_VIKI - -// SSD1306 OLED generic display support -// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: https://github.com/olikraus/U8glib_Arduino +// +// +// Activate this directive if you have a SSD1306 OLED full graphics generic display +// //#define U8GLIB_SSD1306 -// Shift register panels -// --------------------- -// 2 wire Non-latching LCD SR from: -// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection +// +// CONTROLLER TYPE: Shift register panels +// +// 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH // LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// //#define SAV_3DLCD // @section extras