Azteeg X3 Pro Pin Revisions

I added the fan pins in here and left them at -1 in configuration_adv.h
and it works fine. Pinned for a 4 extruder from 1-4 and HE5 being the
controller fan, HE6 being the Extruder Auto Fan/Water pump in the Kraken
case, and HE7 being for part cooling fan. Added in descriptions for the
MIN MAX pin swap and for servo motor additions.
2.0.x
Natealus 10 years ago
parent 93dc0d0518
commit 22bea37393

@ -5,9 +5,35 @@
#include "pins_RAMPS_13.h" #include "pins_RAMPS_13.h"
#undef FAN_PIN #undef FAN_PIN
#define FAN_PIN 9 // (Sprinter config) #define FAN_PIN 6 //Part Cooling System
#define BEEPER 33 #define BEEPER 33
#define CONTROLLERFAN_PIN 4 //Pin used for the fan to cool motherboard (-1 to disable)
//Fans/Water Pump to cool the hotend cool side.
#define EXTRUDER_0_AUTO_FAN_PIN 5
#define EXTRUDER_1_AUTO_FAN_PIN 5
#define EXTRUDER_2_AUTO_FAN_PIN 5
#define EXTRUDER_3_AUTO_FAN_PIN 5
//
//This section is to swap the MIN and MAX pins because the X3 Pro comes with only
//MIN endstops soldered onto the board. Delta code wants the homing endstops to be
//the MAX so I swapped them here. Comment them out with // if you want them original.
//Note: I had to solder on the additional MAX Endstop pins to attach a Z-Probe
//endstop switch.
//
#undef X_MIN_PIN
#undef X_MAX_PIN
#undef Y_MIN_PIN
#undef Y_MAX_PIN
#undef Z_MIN_PIN
#undef Z_MAX_PIN
#define X_MIN_PIN 2
#define X_MAX_PIN 3
#define Y_MIN_PIN 15
#define Y_MAX_PIN 14
#define Z_MIN_PIN 19
#define Z_MAX_PIN 18
//
#define E2_STEP_PIN 23 #define E2_STEP_PIN 23
#define E2_DIR_PIN 25 #define E2_DIR_PIN 25
@ -24,7 +50,7 @@
#undef HEATER_1_PIN #undef HEATER_1_PIN
#undef HEATER_2_PIN #undef HEATER_2_PIN
#undef HEATER_3_PIN #undef HEATER_3_PIN
#define HEATER_1_PIN -1 #define HEATER_1_PIN 9
#define HEATER_2_PIN 16 #define HEATER_2_PIN 16
#define HEATER_3_PIN 17 #define HEATER_3_PIN 17
#define HEATER_4_PIN 4 #define HEATER_4_PIN 4
@ -39,3 +65,26 @@
#define TEMP_4_PIN 10 // ANALOG NUMBERING #define TEMP_4_PIN 10 // ANALOG NUMBERING
#define TC1 4 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro #define TC1 4 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro
#define TC2 5 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro #define TC2 5 // ANALOG NUMBERING Thermo couple on Azteeg X3Pro
//
//These Servo pins are for when they are defined. Tested for usage with bed leveling
//on a Delta with 1 servo. Running through the Z servo endstop in code.
//Physical wire attachment was done on EXT1 on the GND, 5V, and D47 pins.
//
#undef SERVO0_PIN
#undef SERVO1_PIN
#undef SERVO2_PIN
#undef SERVO3_PIN
#ifdef NUM_SERVOS
#define SERVO0_PIN -1
#if NUM_SERVOS > 1
#define SERVO1_PIN -1
#if NUM_SERVOS > 2
#define SERVO2_PIN 47
#if NUM_SERVOS > 3
#define SERVO3_PIN -1
#endif
#endif
#endif
#endif

Loading…
Cancel
Save