melch
/
Marlin
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity

reformating and some minor bugs/things found on the way.

Browse Source
2.0.x
Bernhard Kubicek 13 years ago
parent 900e0c9bf2
commit 1d171e9e52
17 changed files with 1204 additions and 1192 deletions
Show Stats Download Patch File Download Diff File

89
Marlin/Configuration.h
Unescape Escape View File

@ -1,5 +1,5 @@
#ifndef CONFIGURATION_H
#define CONFIGURATION_H
#ifndef __CONFIGURATION_H
#define __CONFIGURATION_H
//#define DEBUG_STEPS
@ -118,10 +118,7 @@ const int dropsegments=5; //everything with this number of steps will be ignore
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
//note: on bernhards ultimaker 200 200 12 are working well.
#define HOMING_FEEDRATE {50*60, 50*60, 12*60, 0} // set the homing speeds
//the followint checks if an extrusion is existent in the move. if _not_, the speed of the move is set to the maximum speed.
//!!!!!!Use only if you know that your printer works at the maximum declared speeds.
// works around the skeinforge cool-bug. There all moves are slowed to have a minimum layer time. However slow travel moves= ooze
#define TRAVELING_AT_MAXSPEED
#define AXIS_RELATIVE_MODES {false, false, false, false}
#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
@ -177,41 +174,50 @@ const int dropsegments=5; //everything with this number of steps will be ignore
//#define_HEATER_1_MAXTEMP 275
//#define BED_MAXTEMP 150
/// PID settings:
// Uncomment the following line to enable PID support.
#define PIDTEMP
#ifdef PIDTEMP
/// PID settings:
// Uncomment the following line to enable PID support.
//#define SMOOTHING
//#define SMOOTHFACTOR 5.0
//float current_raw_average=0;
#define K1 0.95 //smoothing of the PID
//#define PID_DEBUG // Sends debug data to the serial port.
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104 sets the output power in %
#define PID_MAX 255 // limits current to nozzle
#define PID_INTEGRAL_DRIVE_MAX 255
#define PID_dT 0.1
//machine with red silicon: 1950:45 second ; with fan fully blowin 3000:47
#define PID_MAX 255 // limits current to nozzle; 255=full current
#define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term
#define K1 0.95 //smoothing factor withing the PID
#define PID_dT 0.1 //sampling period of the PID
//To develop some PID settings for your machine, you can initiall follow
// the Ziegler-Nichols method.
// set Ki and Kd to zero.
// heat with a defined Kp and see if the temperature stabilizes
// ideally you do this graphically with repg.
// the PID_CRITIAL_GAIN should be the Kp at which temperature oscillatins are not dampned out/decreas in amplitutde
// PID_SWING_AT_CRITIAL is the time for a full period of the oscillations at the critical Gain
// usually further manual tunine is necessary.
#define PID_CRITIAL_GAIN 3000
#define PID_SWING_AT_CRITIAL 45 //seconds
#define PIDIADD 5
/*
//PID according to Ziegler-Nichols method
float Kp = 0.6*PID_CRITIAL_GAIN;
float Ki =PIDIADD+2*Kp/PID_SWING_AT_CRITIAL*PID_dT;
float Kd = Kp*PID_SWING_AT_CRITIAL/8./PID_dT;
*/
//PI according to Ziegler-Nichols method
#define DEFAULT_Kp (PID_CRITIAL_GAIN/2.2)
#define DEFAULT_Ki (1.2*Kp/PID_SWING_AT_CRITIAL*PID_dT)
#define DEFAULT_Kd (0)
#define PID_PI //no differentail term
//#define PID_PID //normal PID
#ifdef PID_PID
//PID according to Ziegler-Nichols method
#define DEFAULT_Kp (0.6*PID_CRITIAL_GAIN)
#define DEFAULT_Ki (2*Kp/PID_SWING_AT_CRITIAL*PID_dT)
#define DEFAULT_Kd (PID_SWING_AT_CRITIAL/8./PID_dT)
#endif
#ifdef PID_PI
//PI according to Ziegler-Nichols method
#define DEFAULT_Kp (PID_CRITIAL_GAIN/2.2)
#define DEFAULT_Ki (1.2*Kp/PID_SWING_AT_CRITIAL*PID_dT)
#define DEFAULT_Kd (0)
#endif
// this adds an experimental additional term to the heatingpower, proportional to the extrusion speed.
// if Kc is choosen well, the additional required power due to increased melting should be compensated.
#define PID_ADD_EXTRUSION_RATE
#ifdef PID_ADD_EXTRUSION_RATE
#define DEFAULT_Kc (5) //heatingpower=Kc*(e_speed)
@ -228,22 +234,21 @@ const int dropsegments=5; //everything with this number of steps will be ignore
//#define ADVANCE
#ifdef ADVANCE
#define EXTRUDER_ADVANCE_K .3
#define EXTRUDER_ADVANCE_K .3
#define D_FILAMENT 1.7
#define STEPS_MM_E 65
#define EXTRUTION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
#define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUTION_AREA)
#define D_FILAMENT 1.7
#define STEPS_MM_E 65
#define EXTRUTION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
#define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUTION_AREA)
#endif // ADVANCE
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, e.g. 8,16,32
#if defined SDSUPPORT
// The number of linear motions that can be in the plan at any give time.
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering.
#if defined SDSUPPORT
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
#else
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
#endif
#endif
#endif //__CONFIGURATION_H

117
Marlin/EEPROMwrite.h
Unescape Escape View File

@ -1,39 +1,42 @@
#ifndef __EEPROMH
#define __EEPROMH
#include "Marlin.h"
#include "planner.h"
#include "temperature.h"
#include <EEPROM.h>
#include "Marlin.h"
#include "streaming.h"
//======================================================================================
template <class T> int EEPROM_writeAnything(int &ee, const T& value)
{
const byte* p = (const byte*)(const void*)&value;
int i;
for (i = 0; i < (int)sizeof(value); i++)
EEPROM.write(ee++, *p++);
return i;
const byte* p = (const byte*)(const void*)&value;
int i;
for (i = 0; i < (int)sizeof(value); i++)
EEPROM.write(ee++, *p++);
return i;
}
//======================================================================================
template <class T> int EEPROM_readAnything(int &ee, T& value)
{
byte* p = (byte*)(void*)&value;
int i;
for (i = 0; i < (int)sizeof(value); i++)
*p++ = EEPROM.read(ee++);
return i;
byte* p = (byte*)(void*)&value;
int i;
for (i = 0; i < (int)sizeof(value); i++)
*p++ = EEPROM.read(ee++);
return i;
}
//======================================================================================
#define EEPROM_OFFSET 100
#define EEPROM_VERSION "V04" // IMPORTANT: Whenever there are changes made to the variables stored in EEPROM
// in the functions below, also increment the version number. This makes sure that
// the default values are used whenever there is a change to the data, to prevent
// wrong data being written to the variables.
// ALSO: always make sure the variables in the Store and retrieve sections are in the same order.
void StoreSettings() {
// IMPORTANT: Whenever there are changes made to the variables stored in EEPROM
// in the functions below, also increment the version number. This makes sure that
// the default values are used whenever there is a change to the data, to prevent
// wrong data being written to the variables.
// ALSO: always make sure the variables in the Store and retrieve sections are in the same order.
#define EEPROM_VERSION "V04"
void StoreSettings()
{
char ver[4]= "000";
int i=EEPROM_OFFSET;
EEPROM_writeAnything(i,ver); // invalidate data first
@ -48,52 +51,55 @@ void StoreSettings() {
EEPROM_writeAnything(i,max_xy_jerk);
EEPROM_writeAnything(i,max_z_jerk);
#ifdef PIDTEMP
EEPROM_writeAnything(i,Kp);
EEPROM_writeAnything(i,Ki);
EEPROM_writeAnything(i,Kd);
#else
EEPROM_writeAnything(i,3000);
EEPROM_writeAnything(i,0);
EEPROM_writeAnything(i,0);
#endif
EEPROM_writeAnything(i,Kp);
EEPROM_writeAnything(i,Ki);
EEPROM_writeAnything(i,Kd);
#else
EEPROM_writeAnything(i,3000);
EEPROM_writeAnything(i,0);
EEPROM_writeAnything(i,0);
#endif
char ver2[4]=EEPROM_VERSION;
i=EEPROM_OFFSET;
EEPROM_writeAnything(i,ver2); // validate data
SERIAL_ECHOLN("Settings Stored");
SERIAL_ECHOLN("Settings Stored");
}
void RetrieveSettings(bool def=false){ // if def=true, the default values will be used
void RetrieveSettings(bool def=false)
{ // if def=true, the default values will be used
int i=EEPROM_OFFSET;
char stored_ver[4];
char ver[4]=EEPROM_VERSION;
EEPROM_readAnything(i,stored_ver); //read stored version
// SERIAL_ECHOLN("Version: [" << ver << "] Stored version: [" << stored_ver << "]");
if ((!def)&&(strncmp(ver,stored_ver,3)==0)) { // version number match
EEPROM_readAnything(i,axis_steps_per_unit);
EEPROM_readAnything(i,max_feedrate);
EEPROM_readAnything(i,max_acceleration_units_per_sq_second);
EEPROM_readAnything(i,acceleration);
EEPROM_readAnything(i,retract_acceleration);
EEPROM_readAnything(i,minimumfeedrate);
EEPROM_readAnything(i,mintravelfeedrate);
EEPROM_readAnything(i,minsegmenttime);
EEPROM_readAnything(i,max_xy_jerk);
EEPROM_readAnything(i,max_z_jerk);
#ifndef PIDTEMP
// SERIAL_ECHOLN("Version: [" << ver << "] Stored version: [" << stored_ver << "]");
if ((!def)&&(strncmp(ver,stored_ver,3)==0))
{ // version number match
EEPROM_readAnything(i,axis_steps_per_unit);
EEPROM_readAnything(i,max_feedrate);
EEPROM_readAnything(i,max_acceleration_units_per_sq_second);
EEPROM_readAnything(i,acceleration);
EEPROM_readAnything(i,retract_acceleration);
EEPROM_readAnything(i,minimumfeedrate);
EEPROM_readAnything(i,mintravelfeedrate);
EEPROM_readAnything(i,minsegmenttime);
EEPROM_readAnything(i,max_xy_jerk);
EEPROM_readAnything(i,max_z_jerk);
#ifndef PIDTEMP
float Kp,Ki,Kd;
#endif
EEPROM_readAnything(i,Kp);
EEPROM_readAnything(i,Ki);
EEPROM_readAnything(i,Kd);
#endif
EEPROM_readAnything(i,Kp);
EEPROM_readAnything(i,Ki);
EEPROM_readAnything(i,Kd);
SERIAL_ECHOLN("Stored settings retreived:");
SERIAL_ECHOLN("Stored settings retreived:");
}
else {
else
{
float tmp1[]=DEFAULT_AXIS_STEPS_PER_UNIT;
float tmp2[]=DEFAULT_MAX_FEEDRATE;
long tmp3[]=DEFAULT_MAX_ACCELERATION;
for (int i=0;i<4;i++) {
for (short i=0;i<4;i++)
{
axis_steps_per_unit[i]=tmp1[i];
max_feedrate[i]=tmp2[i];
max_acceleration_units_per_sq_second[i]=tmp3[i];
@ -117,11 +123,10 @@ void RetrieveSettings(bool def=false){ // if def=true, the default values will
SERIAL_ECHOLN(" M204 S" <<_FLOAT(acceleration,2) << " T" << _FLOAT(retract_acceleration,2));
SERIAL_ECHOLN("Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum xY jerk (mm/s), Z=maximum Z jerk (mm/s)");
SERIAL_ECHOLN(" M205 S" <<_FLOAT(minimumfeedrate/60,2) << " T" << _FLOAT(mintravelfeedrate/60,2) << " B" << _FLOAT(minsegmenttime,2) << " X" << _FLOAT(max_xy_jerk/60,2) << " Z" << _FLOAT(max_z_jerk/60,2));
#ifdef PIDTEMP
SERIAL_ECHOLN("PID settings:");
SERIAL_ECHOLN(" M301 P" << _FLOAT(Kp,3) << " I" << _FLOAT(Ki,3) << " D" << _FLOAT(Kd,3));
#endif
#ifdef PIDTEMP
SERIAL_ECHOLN("PID settings:");
SERIAL_ECHOLN(" M301 P" << _FLOAT(Kp,3) << " I" << _FLOAT(Ki,3) << " D" << _FLOAT(Kd,3));
#endif
}
#endif

57
Marlin/Marlin.h
Unescape Escape View File

@ -18,41 +18,39 @@ void process_commands();
void manage_inactivity(byte debug);
#if X_ENABLE_PIN > -1
#define enable_x() WRITE(X_ENABLE_PIN, X_ENABLE_ON)
#define disable_x() WRITE(X_ENABLE_PIN,!X_ENABLE_ON)
#define enable_x() WRITE(X_ENABLE_PIN, X_ENABLE_ON)
#define disable_x() WRITE(X_ENABLE_PIN,!X_ENABLE_ON)
#else
#define enable_x() ;
#define disable_x() ;
#define enable_x() ;
#define disable_x() ;
#endif
#if Y_ENABLE_PIN > -1
#define enable_y() WRITE(Y_ENABLE_PIN, Y_ENABLE_ON)
#define disable_y() WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON)
#define enable_y() WRITE(Y_ENABLE_PIN, Y_ENABLE_ON)
#define disable_y() WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON)
#else
#define enable_y() ;
#define disable_y() ;
#define enable_y() ;
#define disable_y() ;
#endif
#if Z_ENABLE_PIN > -1
#define enable_z() WRITE(Z_ENABLE_PIN, Z_ENABLE_ON)
#define disable_z() WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON)
#define enable_z() WRITE(Z_ENABLE_PIN, Z_ENABLE_ON)
#define disable_z() WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON)
#else
#define enable_z() ;
#define disable_z() ;
#define enable_z() ;
#define disable_z() ;
#endif
#if E_ENABLE_PIN > -1
#define enable_e() WRITE(E_ENABLE_PIN, E_ENABLE_ON)
#define disable_e() WRITE(E_ENABLE_PIN,!E_ENABLE_ON)
#define enable_e() WRITE(E_ENABLE_PIN, E_ENABLE_ON)
#define disable_e() WRITE(E_ENABLE_PIN,!E_ENABLE_ON)
#else
#define enable_e() ;
#define disable_e() ;
#define enable_e() ;
#define disable_e() ;
#endif
#define X_AXIS 0
#define Y_AXIS 1
#define Z_AXIS 2
#define E_AXIS 3
enum AxisEnum {X_AXIS=0, Y_AXIS=1, Z_AXIS=2, E_AXIS=3};
void FlushSerialRequestResend();
void ClearToSend();
@ -61,26 +59,15 @@ void get_coordinates();
void prepare_move();
void kill();
//void check_axes_activity();
//void plan_init();
//void st_init();
//void tp_init();
//void plan_buffer_line(float x, float y, float z, float e, float feed_rate);
//void plan_set_position(float x, float y, float z, float e);
//void st_wake_up();
//void st_synchronize();
void enquecommand(const char *cmd); //put an ascii command at the end of the current buffer.
#ifndef CRITICAL_SECTION_START
#define CRITICAL_SECTION_START unsigned char _sreg = SREG; cli();
#define CRITICAL_SECTION_END SREG = _sreg;
#define CRITICAL_SECTION_START unsigned char _sreg = SREG; cli();
#define CRITICAL_SECTION_END SREG = _sreg;
#endif //CRITICAL_SECTION_START
extern float homing_feedrate[];
extern bool axis_relative_modes[];
void kill();
#endif

781
Marlin/Marlin.pde
View File

File diff suppressed because it is too large Load Diff

18
Marlin/motion_control.cpp
Unescape Escape View File

@ -33,8 +33,8 @@
void mc_arc(float *position, float *target, float *offset, uint8_t axis_0, uint8_t axis_1,
uint8_t axis_linear, float feed_rate, float radius, uint8_t isclockwise)
{
// int acceleration_manager_was_enabled = plan_is_acceleration_manager_enabled();
// plan_set_acceleration_manager_enabled(false); // disable acceleration management for the duration of the arc
// int acceleration_manager_was_enabled = plan_is_acceleration_manager_enabled();
// plan_set_acceleration_manager_enabled(false); // disable acceleration management for the duration of the arc
SERIAL_ECHOLN("mc_arc.");
float center_axis0 = position[axis_0] + offset[axis_0];
float center_axis1 = position[axis_1] + offset[axis_1];
@ -52,12 +52,12 @@ void mc_arc(float *position, float *target, float *offset, uint8_t axis_0, uint8
float millimeters_of_travel = hypot(angular_travel*radius, fabs(linear_travel));
if (millimeters_of_travel == 0.0) { return; }
uint16_t segments = floor(millimeters_of_travel/MM_PER_ARC_SEGMENT);
/*
// Multiply inverse feed_rate to compensate for the fact that this movement is approximated
// by a number of discrete segments. The inverse feed_rate should be correct for the sum of
// all segments.
if (invert_feed_rate) { feed_rate *= segments; }
*/
/*
// Multiply inverse feed_rate to compensate for the fact that this movement is approximated
// by a number of discrete segments. The inverse feed_rate should be correct for the sum of
// all segments.
if (invert_feed_rate) { feed_rate *= segments; }
*/
float theta_per_segment = angular_travel/segments;
float linear_per_segment = linear_travel/segments;
@ -128,6 +128,6 @@ void mc_arc(float *position, float *target, float *offset, uint8_t axis_0, uint8
// Ensure last segment arrives at target location.
plan_buffer_line(target[X_AXIS], target[Y_AXIS], target[Z_AXIS], target[E_AXIS], feed_rate);
// plan_set_acceleration_manager_enabled(acceleration_manager_was_enabled);
// plan_set_acceleration_manager_enabled(acceleration_manager_was_enabled);
}

68
Marlin/pins.h
Unescape Escape View File

@ -557,6 +557,74 @@
#define FAN_PIN 7
#define PS_ON_PIN 12
#define KILL_PIN -1
#ifdef ULTRA_LCD
#ifdef NEWPANEL
//arduino pin witch triggers an piezzo beeper
#define BEEPER 18
#define LCD_PINS_RS 20
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 16
#define LCD_PINS_D5 21
#define LCD_PINS_D6 5
#define LCD_PINS_D7 6
//buttons are directly attached
#define BTN_EN1 40
#define BTN_EN2 42
#define BTN_ENC 19 //the click
#define BLEN_C 2
#define BLEN_B 1
#define BLEN_A 0
#define SDCARDDETECT 38
//encoder rotation values
#define encrot0 0
#define encrot1 2
#define encrot2 3
#define encrot3 1
#else //old style panel with shift register
//arduino pin witch triggers an piezzo beeper
#define BEEPER 18
//buttons are attached to a shift register
#define SHIFT_CLK 38
#define SHIFT_LD 42
#define SHIFT_OUT 40
#define SHIFT_EN 17
#define LCD_PINS_RS 16
#define LCD_PINS_ENABLE 5
#define LCD_PINS_D4 6
#define LCD_PINS_D5 21
#define LCD_PINS_D6 20
#define LCD_PINS_D7 19
//encoder rotation values
#define encrot0 0
#define encrot1 2
#define encrot2 3
#define encrot3 1
//bits in the shift register that carry the buttons for:
// left up center down right red
#define BL_LE 7
#define BL_UP 6
#define BL_MI 5
#define BL_DW 4
#define BL_RI 3
#define BL_ST 2
#define BLEN_B 1
#define BLEN_A 0
#endif
#endif //ULTRA_LCD
#endif

82
Marlin/planner.cpp
Unescape Escape View File

@ -83,7 +83,7 @@ static volatile unsigned char block_buffer_head; // Index of the next
static volatile unsigned char block_buffer_tail; // Index of the block to process now
// The current position of the tool in absolute steps
long position[4];
long position[4];
#define ONE_MINUTE_OF_MICROSECONDS 60000000.0
@ -123,10 +123,10 @@ void calculate_trapezoid_for_block(block_t *block, float entry_speed, float exit
long initial_rate = ceil(block->nominal_rate*entry_factor);
long final_rate = ceil(block->nominal_rate*exit_factor);
#ifdef ADVANCE
long initial_advance = block->advance*entry_factor*entry_factor;
long final_advance = block->advance*exit_factor*exit_factor;
#endif // ADVANCE
#ifdef ADVANCE
long initial_advance = block->advance*entry_factor*entry_factor;
long final_advance = block->advance*exit_factor*exit_factor;
#endif // ADVANCE
// Limit minimal step rate (Otherwise the timer will overflow.)
if(initial_rate <120) initial_rate=120;
@ -155,10 +155,10 @@ void calculate_trapezoid_for_block(block_t *block, float entry_speed, float exit
block->decelerate_after = decelerate_after;
block->initial_rate = initial_rate;
block->final_rate = final_rate;
#ifdef ADVANCE
block->initial_advance = initial_advance;
block->final_advance = final_advance;
#endif //ADVANCE
#ifdef ADVANCE
block->initial_advance = initial_advance;
block->final_advance = final_advance;
#endif //ADVANCE
}
CRITICAL_SECTION_END;
}
@ -166,18 +166,15 @@ void calculate_trapezoid_for_block(block_t *block, float entry_speed, float exit
// Calculates the maximum allowable speed at this point when you must be able to reach target_velocity using the
// acceleration within the allotted distance.
inline float max_allowable_speed(float acceleration, float target_velocity, float distance) {
return(
sqrt(target_velocity*target_velocity-2*acceleration*60*60*distance)
);
return sqrt(target_velocity*target_velocity-2*acceleration*60*60*distance);
}
// "Junction jerk" in this context is the immediate change in speed at the junction of two blocks.
// This method will calculate the junction jerk as the euclidean distance between the nominal
// velocities of the respective blocks.
inline float junction_jerk(block_t *before, block_t *after) {
return(sqrt(
pow((before->speed_x-after->speed_x), 2)+
pow((before->speed_y-after->speed_y), 2)));
return sqrt(
pow((before->speed_x-after->speed_x), 2)+pow((before->speed_y-after->speed_y), 2));
}
// Return the safe speed which is max_jerk/2, e.g. the
@ -185,8 +182,10 @@ inline float junction_jerk(block_t *before, block_t *after) {
float safe_speed(block_t *block) {
float safe_speed;
safe_speed = max_xy_jerk/2;
if(abs(block->speed_z) > max_z_jerk/2) safe_speed = max_z_jerk/2;
if (safe_speed > block->nominal_speed) safe_speed = block->nominal_speed;
if(abs(block->speed_z) > max_z_jerk/2)
safe_speed = max_z_jerk/2;
if (safe_speed > block->nominal_speed)
safe_speed = block->nominal_speed;
return safe_speed;
}
@ -379,9 +378,8 @@ void check_axes_activity() {
// Add a new linear movement to the buffer. steps_x, _y and _z is the absolute position in
// mm. Microseconds specify how many microseconds the move should take to perform. To aid acceleration
// calculation the caller must also provide the physical length of the line in millimeters.
void plan_buffer_line(float x, float y, float z, float e, float feed_rate) {
void plan_buffer_line(const float &x, const float &y, const float &z, const float &e, float feed_rate)
{
// Calculate the buffer head after we push this byte
int next_buffer_head = (block_buffer_head + 1) & (BLOCK_BUFFER_SIZE - 1);
@ -469,11 +467,8 @@ void plan_buffer_line(float x, float y, float z, float e, float feed_rate) {
// Limit speed per axis
float speed_factor = 1; //factor <=1 do decrease speed
if(abs(block->speed_x) > max_feedrate[X_AXIS]) {
//// [ErikDeBruijn] IS THIS THE BUG WE'RE LOOING FOR????
//// [bernhard] No its not, according to Zalm.
//// the if would always be true, since tmp_speedfactor <=0 due the inial if, so its safe to set. the next lines actually compare.
speed_factor = max_feedrate[X_AXIS] / abs(block->speed_x);
//if(speed_factor > tmp_speed_factor) speed_factor = tmp_speed_factor;
//if(speed_factor > tmp_speed_factor) speed_factor = tmp_speed_factor; /is not need here because auf the init above
}
if(abs(block->speed_y) > max_feedrate[Y_AXIS]){
float tmp_speed_factor = max_feedrate[Y_AXIS] / abs(block->speed_y);
@ -495,7 +490,8 @@ void plan_buffer_line(float x, float y, float z, float e, float feed_rate) {
block->nominal_speed = block->millimeters * multiplier;
block->nominal_rate = ceil(block->step_event_count * multiplier / 60);
if(block->nominal_rate < 120) block->nominal_rate = 120;
if(block->nominal_rate < 120)
block->nominal_rate = 120;
block->entry_speed = safe_speed(block);
// Compute the acceleration rate for the trapezoid generator.
@ -527,25 +523,25 @@ void plan_buffer_line(float x, float y, float z, float e, float feed_rate) {
block->acceleration = block->acceleration_st * travel_per_step;
block->acceleration_rate = (long)((float)block->acceleration_st * 8.388608);
#ifdef ADVANCE
// Calculate advance rate
if((block->steps_e == 0) || (block->steps_x == 0 && block->steps_y == 0 && block->steps_z == 0)) {
block->advance_rate = 0;
block->advance = 0;
}
else {
long acc_dist = estimate_acceleration_distance(0, block->nominal_rate, block->acceleration_st);
float advance = (STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K) *
(block->speed_e * block->speed_e * EXTRUTION_AREA * EXTRUTION_AREA / 3600.0)*65536;
block->advance = advance;
if(acc_dist == 0) {
#ifdef ADVANCE
// Calculate advance rate
if((block->steps_e == 0) || (block->steps_x == 0 && block->steps_y == 0 && block->steps_z == 0)) {
block->advance_rate = 0;
}
else {
block->advance_rate = advance / (float)acc_dist;
block->advance = 0;
}
}
#endif // ADVANCE
else {
long acc_dist = estimate_acceleration_distance(0, block->nominal_rate, block->acceleration_st);
float advance = (STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K) *
(block->speed_e * block->speed_e * EXTRUTION_AREA * EXTRUTION_AREA / 3600.0)*65536;
block->advance = advance;
if(acc_dist == 0) {
block->advance_rate = 0;
}
else {
block->advance_rate = advance / (float)acc_dist;
}
}
#endif // ADVANCE
// compute a preliminary conservative acceleration trapezoid
float safespeed = safe_speed(block);
@ -576,7 +572,7 @@ void plan_buffer_line(float x, float y, float z, float e, float feed_rate) {
st_wake_up();
}
void plan_set_position(float x, float y, float z, float e)
void plan_set_position(const float &x, const float &y, const float &z, const float &e)
{
position[X_AXIS] = lround(x*axis_steps_per_unit[X_AXIS]);
position[Y_AXIS] = lround(y*axis_steps_per_unit[Y_AXIS]);

25
Marlin/planner.h
Unescape Escape View File

@ -32,16 +32,16 @@ typedef struct {
// Fields used by the bresenham algorithm for tracing the line
long steps_x, steps_y, steps_z, steps_e; // Step count along each axis
long step_event_count; // The number of step events required to complete this block
volatile long accelerate_until; // The index of the step event on which to stop acceleration
volatile long decelerate_after; // The index of the step event on which to start decelerating
volatile long acceleration_rate; // The acceleration rate used for acceleration calculation
volatile long accelerate_until; // The index of the step event on which to stop acceleration
volatile long decelerate_after; // The index of the step event on which to start decelerating
volatile long acceleration_rate; // The acceleration rate used for acceleration calculation
unsigned char direction_bits; // The direction bit set for this block (refers to *_DIRECTION_BIT in config.h)
#ifdef ADVANCE
long advance_rate;
volatile long initial_advance;
volatile long final_advance;
float advance;
#endif
#ifdef ADVANCE
long advance_rate;
volatile long initial_advance;
volatile long final_advance;
float advance;
#endif
// Fields used by the motion planner to manage acceleration
float speed_x, speed_y, speed_z, speed_e; // Nominal mm/minute for each axis
@ -57,16 +57,17 @@ typedef struct {
long acceleration_st; // acceleration steps/sec^2
volatile char busy;
} block_t;
// Initialize the motion plan subsystem
void plan_init();
// Add a new linear movement to the buffer. x, y and z is the signed, absolute target position in
// millimaters. Feed rate specifies the speed of the motion.
void plan_buffer_line(float x, float y, float z, float e, float feed_rate);
void plan_buffer_line(const float &x, const float &y, const float &z, const float &e, float feed_rate);
// Set position. Used for G92 instructions.
void plan_set_position(float x, float y, float z, float e);
void plan_set_position(const float &x, const float &y, const float &z, const float &e);
// Called when the current block is no longer needed. Discards the block and makes the memory
// availible for new blocks.

1
Marlin/speed_lookuptable.h
Unescape Escape View File

@ -37,6 +37,7 @@ uint16_t speed_lookuptable_fast[256][2] PROGMEM = {\
{ 32, 0}, { 32, 0}, { 32, 0}, { 32, 0}, { 32, 1}, { 31, 0}, { 31, 0}, { 31, 0},
{ 31, 0}, { 31, 0}, { 31, 0}, { 31, 1}, { 30, 0}, { 30, 0}, { 30, 0}, { 30, 0}
};
uint16_t speed_lookuptable_slow[256][2] PROGMEM = {\
{ 62500, 12500}, { 50000, 8334}, { 41666, 5952}, { 35714, 4464}, { 31250, 3473}, { 27777, 2777}, { 25000, 2273}, { 22727, 1894},
{ 20833, 1603}, { 19230, 1373}, { 17857, 1191}, { 16666, 1041}, { 15625, 920}, { 14705, 817}, { 13888, 731}, { 13157, 657},

402
Marlin/stepper.cpp
Unescape Escape View File

@ -35,8 +35,8 @@
// if DEBUG_STEPS is enabled, M114 can be used to compare two methods of determining the X,Y,Z position of the printer.
// for debugging purposes only, should be disabled by default
#ifdef DEBUG_STEPS
volatile long count_position[NUM_AXIS] = { 0, 0, 0, 0};
volatile int count_direction[NUM_AXIS] = { 1, 1, 1, 1};
volatile long count_position[NUM_AXIS] = { 0, 0, 0, 0};
volatile int count_direction[NUM_AXIS] = { 1, 1, 1, 1};
#endif
@ -117,6 +117,8 @@ asm volatile ( \
block_t *current_block; // A pointer to the block currently being traced
//static makes it inpossible to be called from outside of this file by extern.!
// Variables used by The Stepper Driver Interrupt
static unsigned char out_bits; // The next stepping-bits to be output
static long counter_x, // Counter variables for the bresenham line tracer
@ -125,9 +127,9 @@ static long counter_x, // Counter variables for the bresenham line tracer
counter_e;
static unsigned long step_events_completed; // The number of step events executed in the current block
#ifdef ADVANCE
static long advance_rate, advance, final_advance = 0;
static short old_advance = 0;
static short e_steps;
static long advance_rate, advance, final_advance = 0;
static short old_advance = 0;
static short e_steps;
#endif
static unsigned char busy = false; // TRUE when SIG_OUTPUT_COMPARE1A is being serviced. Used to avoid retriggering that handler.
static long acceleration_time, deceleration_time;
@ -195,10 +197,10 @@ inline unsigned short calc_timer(unsigned short step_rate) {
// Initializes the trapezoid generator from the current block. Called whenever a new
// block begins.
inline void trapezoid_generator_reset() {
#ifdef ADVANCE
advance = current_block->initial_advance;
final_advance = current_block->final_advance;
#endif
#ifdef ADVANCE
advance = current_block->initial_advance;
final_advance = current_block->final_advance;
#endif
deceleration_time = 0;
// advance_rate = current_block->advance_rate;
// step_rate to timer interval
@ -211,7 +213,8 @@ inline void trapezoid_generator_reset() {
// It pops blocks from the block_buffer and executes them by pulsing the stepper pins appropriately.
ISR(TIMER1_COMPA_vect)
{
if(busy){ SERIAL_ERRORLN(*(unsigned short *)OCR1A<< " ISR overtaking itself.");
if(busy){
SERIAL_ERRORLN(*(unsigned short *)OCR1A<< " ISR overtaking itself.");
return;
} // The busy-flag is used to avoid reentering this interrupt
@ -242,74 +245,74 @@ ISR(TIMER1_COMPA_vect)
// Set directions TO DO This should be done once during init of trapezoid. Endstops -> interrupt
out_bits = current_block->direction_bits;
#ifdef ADVANCE
// Calculate E early.
counter_e += current_block->steps_e;
if (counter_e > 0) {
counter_e -= current_block->step_event_count;
if ((out_bits & (1<<E_AXIS)) != 0) { // - direction
#ifdef ADVANCE
// Calculate E early.
counter_e += current_block->steps_e;
if (counter_e > 0) {
counter_e -= current_block->step_event_count;
if ((out_bits & (1<<E_AXIS)) != 0) { // - direction
CRITICAL_SECTION_START;
e_steps--;
CRITICAL_SECTION_END;
}
else {
CRITICAL_SECTION_START;
e_steps++;
CRITICAL_SECTION_END;
}
}
// Do E steps + advance steps
CRITICAL_SECTION_START;
e_steps--;
e_steps += ((advance >> 16) - old_advance);
CRITICAL_SECTION_END;
}
else {
CRITICAL_SECTION_START;
e_steps++;
CRITICAL_SECTION_END;
}
}
// Do E steps + advance steps
CRITICAL_SECTION_START;
e_steps += ((advance >> 16) - old_advance);
CRITICAL_SECTION_END;
old_advance = advance >> 16;
#endif //ADVANCE
old_advance = advance >> 16;
#endif //ADVANCE
// Set direction en check limit switches
if ((out_bits & (1<<X_AXIS)) != 0) { // -direction
if ((out_bits & (1<<X_AXIS)) != 0) { // -direction
WRITE(X_DIR_PIN, INVERT_X_DIR);
#ifdef DEBUG_STEPS
count_direction[X_AXIS]=-1;
count_direction[X_AXIS]=-1;
#endif
#if X_MIN_PIN > -1
if(READ(X_MIN_PIN) != ENDSTOPS_INVERTING) {
step_events_completed = current_block->step_event_count;
}
#endif
#if X_MIN_PIN > -1
if(READ(X_MIN_PIN) != ENDSTOPS_INVERTING) {
step_events_completed = current_block->step_event_count;
}
#endif
}
else { // +direction
WRITE(X_DIR_PIN,!INVERT_X_DIR);
#ifdef DEBUG_STEPS
WRITE(X_DIR_PIN,!INVERT_X_DIR);
#ifdef DEBUG_STEPS
count_direction[X_AXIS]=1;
#endif
#if X_MAX_PIN > -1
#endif
#if X_MAX_PIN > -1
if((READ(X_MAX_PIN) != ENDSTOPS_INVERTING) && (current_block->steps_x >0)){
step_events_completed = current_block->step_event_count;
}
#endif
#endif
}
if ((out_bits & (1<<Y_AXIS)) != 0) { // -direction
WRITE(Y_DIR_PIN,INVERT_Y_DIR);
#ifdef DEBUG_STEPS
count_direction[Y_AXIS]=-1;
count_direction[Y_AXIS]=-1;
#endif
#if Y_MIN_PIN > -1
if(READ(Y_MIN_PIN) != ENDSTOPS_INVERTING) {
step_events_completed = current_block->step_event_count;
}
#endif
#if Y_MIN_PIN > -1
if(READ(Y_MIN_PIN) != ENDSTOPS_INVERTING) {
step_events_completed = current_block->step_event_count;
}
#endif
}
else { // +direction
WRITE(Y_DIR_PIN,!INVERT_Y_DIR);
#ifdef DEBUG_STEPS
count_direction[Y_AXIS]=1;
count_direction[Y_AXIS]=1;
#endif
#if Y_MAX_PIN > -1
if((READ(Y_MAX_PIN) != ENDSTOPS_INVERTING) && (current_block->steps_y >0)){
step_events_completed = current_block->step_event_count;
}
#endif
#if Y_MAX_PIN > -1
if((READ(Y_MAX_PIN) != ENDSTOPS_INVERTING) && (current_block->steps_y >0)){
step_events_completed = current_block->step_event_count;
}
#endif
}
if ((out_bits & (1<<Z_AXIS)) != 0) { // -direction
@ -317,30 +320,30 @@ if ((out_bits & (1<<X_AXIS)) != 0) { // -direction
#ifdef DEBUG_STEPS
count_direction[Z_AXIS]=-1;
#endif
#if Z_MIN_PIN > -1
if(READ(Z_MIN_PIN) != ENDSTOPS_INVERTING) {
step_events_completed = current_block->step_event_count;
}
#endif
#if Z_MIN_PIN > -1
if(READ(Z_MIN_PIN) != ENDSTOPS_INVERTING) {
step_events_completed = current_block->step_event_count;
}
#endif
}
else { // +direction
WRITE(Z_DIR_PIN,!INVERT_Z_DIR);
#ifdef DEBUG_STEPS
WRITE(Z_DIR_PIN,!INVERT_Z_DIR);
#ifdef DEBUG_STEPS
count_direction[Z_AXIS]=1;
#endif
#if Z_MAX_PIN > -1
#endif
#if Z_MAX_PIN > -1
if((READ(Z_MAX_PIN) != ENDSTOPS_INVERTING) && (current_block->steps_z >0)){
step_events_completed = current_block->step_event_count;
}
#endif
#endif
}
#ifndef ADVANCE
if ((out_bits & (1<<E_AXIS)) != 0) // -direction
WRITE(E_DIR_PIN,INVERT_E_DIR);
else // +direction
WRITE(E_DIR_PIN,!INVERT_E_DIR);
#endif //!ADVANCE
#ifndef ADVANCE
if ((out_bits & (1<<E_AXIS)) != 0) // -direction
WRITE(E_DIR_PIN,INVERT_E_DIR);
else // +direction
WRITE(E_DIR_PIN,!INVERT_E_DIR);
#endif //!ADVANCE
for(char i=0; i < step_loops; i++) { // Take multiple steps per interrupt (For high speed moves)
counter_x += current_block->steps_x;
@ -349,7 +352,7 @@ if ((out_bits & (1<<X_AXIS)) != 0) { // -direction
counter_x -= current_block->step_event_count;
WRITE(X_STEP_PIN, LOW);
#ifdef DEBUG_STEPS
count_position[X_AXIS]+=count_direction[X_AXIS];
count_position[X_AXIS]+=count_direction[X_AXIS];
#endif
}
@ -359,7 +362,7 @@ if ((out_bits & (1<<X_AXIS)) != 0) { // -direction
counter_y -= current_block->step_event_count;
WRITE(Y_STEP_PIN, LOW);
#ifdef DEBUG_STEPS
count_position[Y_AXIS]+=count_direction[Y_AXIS];
count_position[Y_AXIS]+=count_direction[Y_AXIS];
#endif
}
@ -369,18 +372,18 @@ if ((out_bits & (1<<X_AXIS)) != 0) { // -direction
counter_z -= current_block->step_event_count;
WRITE(Z_STEP_PIN, LOW);
#ifdef DEBUG_STEPS
count_position[Z_AXIS]+=count_direction[Z_AXIS];
count_position[Z_AXIS]+=count_direction[Z_AXIS];
#endif
}
#ifndef ADVANCE
counter_e += current_block->steps_e;
if (counter_e > 0) {
WRITE(E_STEP_PIN, HIGH);
counter_e -= current_block->step_event_count;
WRITE(E_STEP_PIN, LOW);
}
#endif //!ADVANCE
#ifndef ADVANCE
counter_e += current_block->steps_e;
if (counter_e > 0) {
WRITE(E_STEP_PIN, HIGH);
counter_e -= current_block->step_event_count;
WRITE(E_STEP_PIN, LOW);
}
#endif //!ADVANCE
step_events_completed += 1;
if(step_events_completed >= current_block->step_event_count) break;
}
@ -397,9 +400,9 @@ if ((out_bits & (1<<X_AXIS)) != 0) { // -direction
// step_rate to timer interval
timer = calc_timer(acc_step_rate);
#ifdef ADVANCE
advance += advance_rate;
#endif
#ifdef ADVANCE
advance += advance_rate;
#endif
acceleration_time += timer;
OCR1A = timer;
}
@ -419,11 +422,11 @@ if ((out_bits & (1<<X_AXIS)) != 0) { // -direction
// step_rate to timer interval
timer = calc_timer(step_rate);
#ifdef ADVANCE
advance -= advance_rate;
if(advance < final_advance)
advance = final_advance;
#endif //ADVANCE
#ifdef ADVANCE
advance -= advance_rate;
if(advance < final_advance)
advance = final_advance;
#endif //ADVANCE
deceleration_time += timer;
OCR1A = timer;
}
@ -438,127 +441,126 @@ if ((out_bits & (1<<X_AXIS)) != 0) { // -direction
}
#ifdef ADVANCE
unsigned char old_OCR0A;
// Timer interrupt for E. e_steps is set in the main routine;
// Timer 0 is shared with millies
ISR(TIMER0_COMPA_vect)
{
// Critical section needed because Timer 1 interrupt has higher priority.
// The pin set functions are placed on trategic position to comply with the stepper driver timing.
WRITE(E_STEP_PIN, LOW);
// Set E direction (Depends on E direction + advance)
if (e_steps < 0) {
WRITE(E_DIR_PIN,INVERT_E_DIR);
e_steps++;
WRITE(E_STEP_PIN, HIGH);
}
if (e_steps > 0) {
WRITE(E_DIR_PIN,!INVERT_E_DIR);
e_steps--;
WRITE(E_STEP_PIN, HIGH);
unsigned char old_OCR0A;
// Timer interrupt for E. e_steps is set in the main routine;
// Timer 0 is shared with millies
ISR(TIMER0_COMPA_vect)
{
// Critical section needed because Timer 1 interrupt has higher priority.
// The pin set functions are placed on trategic position to comply with the stepper driver timing.
WRITE(E_STEP_PIN, LOW);
// Set E direction (Depends on E direction + advance)
if (e_steps < 0) {
WRITE(E_DIR_PIN,INVERT_E_DIR);
e_steps++;
WRITE(E_STEP_PIN, HIGH);
}
if (e_steps > 0) {
WRITE(E_DIR_PIN,!INVERT_E_DIR);
e_steps--;
WRITE(E_STEP_PIN, HIGH);
}
old_OCR0A += 25; // 10kHz interrupt
OCR0A = old_OCR0A;
}
old_OCR0A += 25; // 10kHz interrupt
OCR0A = old_OCR0A;
}
#endif // ADVANCE
void st_init()
{
//Initialize Dir Pins
#if X_DIR_PIN > -1
SET_OUTPUT(X_DIR_PIN);
#endif
#if Y_DIR_PIN > -1
SET_OUTPUT(Y_DIR_PIN);
#endif
#if Z_DIR_PIN > -1
SET_OUTPUT(Z_DIR_PIN);
#endif
#if E_DIR_PIN > -1
SET_OUTPUT(E_DIR_PIN);
#endif
#if X_DIR_PIN > -1
SET_OUTPUT(X_DIR_PIN);
#endif
#if Y_DIR_PIN > -1
SET_OUTPUT(Y_DIR_PIN);
#endif
#if Z_DIR_PIN > -1
SET_OUTPUT(Z_DIR_PIN);
#endif
#if E_DIR_PIN > -1
SET_OUTPUT(E_DIR_PIN);
#endif
//Initialize Enable Pins - steppers default to disabled.
#if (X_ENABLE_PIN > -1)
SET_OUTPUT(X_ENABLE_PIN);
if(!X_ENABLE_ON) WRITE(X_ENABLE_PIN,HIGH);
#endif
#if (Y_ENABLE_PIN > -1)
SET_OUTPUT(Y_ENABLE_PIN);
if(!Y_ENABLE_ON) WRITE(Y_ENABLE_PIN,HIGH);
#endif
#if (Z_ENABLE_PIN > -1)
SET_OUTPUT(Z_ENABLE_PIN);
if(!Z_ENABLE_ON) WRITE(Z_ENABLE_PIN,HIGH);
#endif
#if (E_ENABLE_PIN > -1)
SET_OUTPUT(E_ENABLE_PIN);
if(!E_ENABLE_ON) WRITE(E_ENABLE_PIN,HIGH);
#endif
#if (X_ENABLE_PIN > -1)
SET_OUTPUT(X_ENABLE_PIN);
if(!X_ENABLE_ON) WRITE(X_ENABLE_PIN,HIGH);
#endif
#if (Y_ENABLE_PIN > -1)
SET_OUTPUT(Y_ENABLE_PIN);
if(!Y_ENABLE_ON) WRITE(Y_ENABLE_PIN,HIGH);
#endif
#if (Z_ENABLE_PIN > -1)
SET_OUTPUT(Z_ENABLE_PIN);
if(!Z_ENABLE_ON) WRITE(Z_ENABLE_PIN,HIGH);
#endif
#if (E_ENABLE_PIN > -1)
SET_OUTPUT(E_ENABLE_PIN);
if(!E_ENABLE_ON) WRITE(E_ENABLE_PIN,HIGH);
#endif
//endstops and pullups
#ifdef ENDSTOPPULLUPS
#if X_MIN_PIN > -1
SET_INPUT(X_MIN_PIN);
WRITE(X_MIN_PIN,HIGH);
#endif
#if X_MAX_PIN > -1
SET_INPUT(X_MAX_PIN);
WRITE(X_MAX_PIN,HIGH);
#endif
#if Y_MIN_PIN > -1
SET_INPUT(Y_MIN_PIN);
WRITE(Y_MIN_PIN,HIGH);
#endif
#if Y_MAX_PIN > -1
SET_INPUT(Y_MAX_PIN);
WRITE(Y_MAX_PIN,HIGH);
#endif
#if Z_MIN_PIN > -1
SET_INPUT(Z_MIN_PIN);
WRITE(Z_MIN_PIN,HIGH);
#endif
#if Z_MAX_PIN > -1
SET_INPUT(Z_MAX_PIN);
WRITE(Z_MAX_PIN,HIGH);
#endif
#else //ENDSTOPPULLUPS
#if X_MIN_PIN > -1
SET_INPUT(X_MIN_PIN);
#endif
#if X_MAX_PIN > -1
SET_INPUT(X_MAX_PIN);
#endif
#if Y_MIN_PIN > -1
SET_INPUT(Y_MIN_PIN);
#endif
#if Y_MAX_PIN > -1
SET_INPUT(Y_MAX_PIN);
#endif
#if Z_MIN_PIN > -1
SET_INPUT(Z_MIN_PIN);
#endif
#if Z_MAX_PIN > -1
SET_INPUT(Z_MAX_PIN);
#endif
#endif //ENDSTOPPULLUPS
#ifdef ENDSTOPPULLUPS
#if X_MIN_PIN > -1
SET_INPUT(X_MIN_PIN);
WRITE(X_MIN_PIN,HIGH);
#endif
#if X_MAX_PIN > -1
SET_INPUT(X_MAX_PIN);
WRITE(X_MAX_PIN,HIGH);
#endif
#if Y_MIN_PIN > -1
SET_INPUT(Y_MIN_PIN);
WRITE(Y_MIN_PIN,HIGH);
#endif
#if Y_MAX_PIN > -1
SET_INPUT(Y_MAX_PIN);
WRITE(Y_MAX_PIN,HIGH);
#endif
#if Z_MIN_PIN > -1
SET_INPUT(Z_MIN_PIN);
WRITE(Z_MIN_PIN,HIGH);
#endif
#if Z_MAX_PIN > -1
SET_INPUT(Z_MAX_PIN);
WRITE(Z_MAX_PIN,HIGH);
#endif
#else //ENDSTOPPULLUPS
#if X_MIN_PIN > -1
SET_INPUT(X_MIN_PIN);
#endif
#if X_MAX_PIN > -1
SET_INPUT(X_MAX_PIN);
#endif
#if Y_MIN_PIN > -1
SET_INPUT(Y_MIN_PIN);
#endif
#if Y_MAX_PIN > -1
SET_INPUT(Y_MAX_PIN);
#endif
#if Z_MIN_PIN > -1
SET_INPUT(Z_MIN_PIN);
#endif
#if Z_MAX_PIN > -1
SET_INPUT(Z_MAX_PIN);
#endif
#endif //ENDSTOPPULLUPS
//Initialize Step Pins
#if (X_STEP_PIN > -1)
SET_OUTPUT(X_STEP_PIN);
#endif
#if (Y_STEP_PIN > -1)
SET_OUTPUT(Y_STEP_PIN);
#endif
#if (Z_STEP_PIN > -1)
SET_OUTPUT(Z_STEP_PIN);
#endif
#if (E_STEP_PIN > -1)
SET_OUTPUT(E_STEP_PIN);
#endif
#if (X_STEP_PIN > -1)
SET_OUTPUT(X_STEP_PIN);
#endif
#if (Y_STEP_PIN > -1)
SET_OUTPUT(Y_STEP_PIN);
#endif
#if (Z_STEP_PIN > -1)
SET_OUTPUT(Z_STEP_PIN);
#endif
#if (E_STEP_PIN > -1)
SET_OUTPUT(E_STEP_PIN);
#endif
// waveform generation = 0100 = CTC
TCCR1B &= ~(1<<WGM13);
@ -574,10 +576,10 @@ void st_init()
OCR1A = 0x4000;
DISABLE_STEPPER_DRIVER_INTERRUPT();
#ifdef ADVANCE
e_steps = 0;
TIMSK0 |= (1<<OCIE0A);
#endif //ADVANCE
#ifdef ADVANCE
e_steps = 0;
TIMSK0 |= (1<<OCIE0A);
#endif //ADVANCE
sei();
}

4
Marlin/stepper.h
Unescape Escape View File

@ -36,8 +36,8 @@ void st_wake_up();
// if DEBUG_STEPS is enabled, M114 can be used to compare two methods of determining the X,Y,Z position of the printer.
// for debugging purposes only, should be disabled by default
#ifdef DEBUG_STEPS
extern volatile long count_position[NUM_AXIS];
extern volatile int count_direction[NUM_AXIS];
extern volatile long count_position[NUM_AXIS];
extern volatile int count_direction[NUM_AXIS];
#endif
extern block_t *current_block; // A pointer to the block currently being traced

389
Marlin/temperature.cpp
Unescape Escape View File

@ -74,24 +74,24 @@ unsigned long previous_millis_heater, previous_millis_bed_heater;
#endif //WATCHPERIOD
#ifdef HEATER_0_MINTEMP
int minttemp_0 = temp2analog(HEATER_0_MINTEMP);
int minttemp_0 = temp2analog(HEATER_0_MINTEMP);
#endif //MINTEMP
#ifdef HEATER_0_MAXTEMP
int maxttemp_0 = temp2analog(HEATER_0_MAXTEMP);
int maxttemp_0 = temp2analog(HEATER_0_MAXTEMP);
#endif //MAXTEMP
#ifdef HEATER_1_MINTEMP
int minttemp_1 = temp2analog(HEATER_1_MINTEMP);
int minttemp_1 = temp2analog(HEATER_1_MINTEMP);
#endif //MINTEMP
#ifdef HEATER_1_MAXTEMP
int maxttemp_1 = temp2analog(HEATER_1_MAXTEMP);
int maxttemp_1 = temp2analog(HEATER_1_MAXTEMP);
#endif //MAXTEMP
#ifdef BED_MINTEMP
int bed_minttemp = temp2analog(BED_MINTEMP);
int bed_minttemp = temp2analog(BED_MINTEMP);
#endif //BED_MINTEMP
#ifdef BED_MAXTEMP
int bed_maxttemp = temp2analog(BED_MAXTEMP);
int bed_maxttemp = temp2analog(BED_MAXTEMP);
#endif //BED_MAXTEMP
void manage_heater()
@ -105,50 +105,49 @@ void manage_heater()
if(temp_meas_ready != true) //better readability
return;
CRITICAL_SECTION_START;
CRITICAL_SECTION_START;
temp_meas_ready = false;
CRITICAL_SECTION_END;
CRITICAL_SECTION_END;
#ifdef PIDTEMP
#ifdef PIDTEMP
pid_input = analog2temp(current_raw[TEMPSENSOR_HOTEND_0]);
#ifndef PID_OPENLOOP
pid_error = pid_setpoint - pid_input;
if(pid_error > 10){
pid_output = PID_MAX;
pid_reset = true;
}
else if(pid_error < -10) {
pid_output = 0;
pid_reset = true;
}
else {
if(pid_reset == true) {
temp_iState = 0.0;
pid_reset = false;
}
pTerm = Kp * pid_error;
temp_iState += pid_error;
temp_iState = constrain(temp_iState, temp_iState_min, temp_iState_max);
iTerm = Ki * temp_iState;
//K1 defined in Configuration.h in the PID settings
#define K2 (1.0-K1)
dTerm = (Kd * (pid_input - temp_dState))*K2 + (K1 * dTerm);
temp_dState = pid_input;
#ifdef PID_ADD_EXTRUSION_RATE
pTerm+=Kc*current_block->speed_e; //additional heating if extrusion speed is high
#endif
pid_output = constrain(pTerm + iTerm - dTerm, 0, PID_MAX);
}
#endif //PID_OPENLOOP
#ifdef PID_DEBUG
SERIAL_ECHOLN(" PIDDEBUG Input "<<pid_input<<" Output "<<pid_output" pTerm "<<pTerm<<" iTerm "<<iTerm<<" dTerm "<<dTerm);
#endif //PID_DEBUG
#ifndef PID_OPENLOOP
pid_error = pid_setpoint - pid_input;
if(pid_error > 10){
pid_output = PID_MAX;
pid_reset = true;
}
else if(pid_error < -10) {
pid_output = 0;
pid_reset = true;
}
else {
if(pid_reset == true) {
temp_iState = 0.0;
pid_reset = false;
}
pTerm = Kp * pid_error;
temp_iState += pid_error;
temp_iState = constrain(temp_iState, temp_iState_min, temp_iState_max);
iTerm = Ki * temp_iState;
//K1 defined in Configuration.h in the PID settings
#define K2 (1.0-K1)
dTerm = (Kd * (pid_input - temp_dState))*K2 + (K1 * dTerm);
temp_dState = pid_input;
#ifdef PID_ADD_EXTRUSION_RATE
pTerm+=Kc*current_block->speed_e; //additional heating if extrusion speed is high
#endif
pid_output = constrain(pTerm + iTerm - dTerm, 0, PID_MAX);
}
#endif //PID_OPENLOOP
#ifdef PID_DEBUG
SERIAL_ECHOLN(" PIDDEBUG Input "<<pid_input<<" Output "<<pid_output" pTerm "<<pTerm<<" iTerm "<<iTerm<<" dTerm "<<dTerm);
#endif //PID_DEBUG
analogWrite(HEATER_0_PIN, pid_output);
#endif //PIDTEMP
#endif //PIDTEMP
#ifndef PIDTEMP
#ifndef PIDTEMP
if(current_raw[0] >= target_raw[0])
{
WRITE(HEATER_0_PIN,LOW);
@ -157,7 +156,7 @@ CRITICAL_SECTION_END;
{
WRITE(HEATER_0_PIN,HIGH);
}
#endif
#endif
if(millis() - previous_millis_bed_heater < BED_CHECK_INTERVAL)
return;
@ -173,7 +172,7 @@ CRITICAL_SECTION_END;
WRITE(HEATER_1_PIN,HIGH);
}
#endif
}
}
// Takes hot end temperature value as input and returns corresponding raw value.
// For a thermistor, it uses the RepRap thermistor temp table.
@ -300,26 +299,26 @@ float analog2tempBed(int raw) {
void tp_init()
{
#if (HEATER_0_PIN > -1)
SET_OUTPUT(HEATER_0_PIN);
#endif
#if (HEATER_1_PIN > -1)
SET_OUTPUT(HEATER_1_PIN);
#endif
#if (HEATER_2_PIN > -1)
SET_OUTPUT(HEATER_2_PIN);
#endif
#if (HEATER_0_PIN > -1)
SET_OUTPUT(HEATER_0_PIN);
#endif
#if (HEATER_1_PIN > -1)
SET_OUTPUT(HEATER_1_PIN);
#endif
#if (HEATER_2_PIN > -1)
SET_OUTPUT(HEATER_2_PIN);
#endif
#ifdef PIDTEMP
temp_iState_min = 0.0;
temp_iState_max = PID_INTEGRAL_DRIVE_MAX / Ki;
#endif //PIDTEMP
#ifdef PIDTEMP
temp_iState_min = 0.0;
temp_iState_max = PID_INTEGRAL_DRIVE_MAX / Ki;
#endif //PIDTEMP
// Set analog inputs
// Set analog inputs
ADCSRA = 1<<ADEN | 1<<ADSC | 1<<ADIF | 0x07;
// Use timer0 for temperature measurement
// Interleave temperature interrupt with millies interrupt
// Use timer0 for temperature measurement
// Interleave temperature interrupt with millies interrupt
OCR0B = 128;
TIMSK0 |= (1<<OCIE0B);
}
@ -344,23 +343,25 @@ void setWatch()
void disable_heater()
{
#if TEMP_0_PIN > -1
#if TEMP_0_PIN > -1
target_raw[0]=0;
#if HEATER_0_PIN > -1
WRITE(HEATER_0_PIN,LOW);
#endif
#endif
#if TEMP_1_PIN > -1
target_raw[1]=0;
#if HEATER_1_PIN > -1
WRITE(HEATER_1_PIN,LOW);
#endif
target_raw[1]=0;
#if HEATER_1_PIN > -1
WRITE(HEATER_1_PIN,LOW);
#endif
#endif
#if TEMP_2_PIN > -1
target_raw[2]=0;
#if HEATER_2_PIN > -1
WRITE(HEATER_2_PIN,LOW);
#endif
target_raw[2]=0;
#if HEATER_2_PIN > -1
WRITE(HEATER_2_PIN,LOW);
#endif
#endif
}
@ -376,75 +377,75 @@ ISR(TIMER0_COMPB_vect)
switch(temp_state) {
case 0: // Prepare TEMP_0
#if (TEMP_0_PIN > -1)
#if TEMP_0_PIN < 8
DIDR0 = 1 << TEMP_0_PIN;
#else
DIDR2 = 1<<(TEMP_0_PIN - 8);
ADCSRB = 1<<MUX5;
#endif
ADMUX = ((1 << REFS0) | (TEMP_0_PIN & 0x07));
ADCSRA |= 1<<ADSC; // Start conversion
#endif
#ifdef ULTIPANEL
buttons_check();
#endif
temp_state = 1;
break;
#if (TEMP_0_PIN > -1)
#if TEMP_0_PIN < 8
DIDR0 = 1 << TEMP_0_PIN;
#else
DIDR2 = 1<<(TEMP_0_PIN - 8);
ADCSRB = 1<<MUX5;
#endif
ADMUX = ((1 << REFS0) | (TEMP_0_PIN & 0x07));
ADCSRA |= 1<<ADSC; // Start conversion
#endif
#ifdef ULTIPANEL
buttons_check();
#endif
temp_state = 1;
break;
case 1: // Measure TEMP_0
#if (TEMP_0_PIN > -1)
raw_temp_0_value += ADC;
#endif
temp_state = 2;
break;
#if (TEMP_0_PIN > -1)
raw_temp_0_value += ADC;
#endif
temp_state = 2;
break;
case 2: // Prepare TEMP_1
#if (TEMP_1_PIN > -1)
#if TEMP_1_PIN < 7
DIDR0 = 1<<TEMP_1_PIN;
#else
DIDR2 = 1<<(TEMP_1_PIN - 8);
ADCSRB = 1<<MUX5;
#endif
ADMUX = ((1 << REFS0) | (TEMP_1_PIN & 0x07));
ADCSRA |= 1<<ADSC; // Start conversion
#endif
#ifdef ULTIPANEL
buttons_check();
#endif
temp_state = 3;
break;
#if (TEMP_1_PIN > -1)
#if TEMP_1_PIN < 7
DIDR0 = 1<<TEMP_1_PIN;
#else
DIDR2 = 1<<(TEMP_1_PIN - 8);
ADCSRB = 1<<MUX5;
#endif
ADMUX = ((1 << REFS0) | (TEMP_1_PIN & 0x07));
ADCSRA |= 1<<ADSC; // Start conversion
#endif
#ifdef ULTIPANEL
buttons_check();
#endif
temp_state = 3;
break;
case 3: // Measure TEMP_1
#if (TEMP_1_PIN > -1)
raw_temp_1_value += ADC;
#endif
temp_state = 4;
break;
#if (TEMP_1_PIN > -1)
raw_temp_1_value += ADC;
#endif
temp_state = 4;
break;
case 4: // Prepare TEMP_2
#if (TEMP_2_PIN > -1)
#if TEMP_2_PIN < 7
DIDR0 = 1 << TEMP_2_PIN;
#else
DIDR2 = 1<<(TEMP_2_PIN - 8);
ADCSRB = 1<<MUX5;
#endif
ADMUX = ((1 << REFS0) | (TEMP_2_PIN & 0x07));
ADCSRA |= 1<<ADSC; // Start conversion
#endif
#ifdef ULTIPANEL
buttons_check();
#endif
temp_state = 5;
break;
#if (TEMP_2_PIN > -1)
#if TEMP_2_PIN < 7
DIDR0 = 1 << TEMP_2_PIN;
#else
DIDR2 = 1<<(TEMP_2_PIN - 8);
ADCSRB = 1<<MUX5;
#endif
ADMUX = ((1 << REFS0) | (TEMP_2_PIN & 0x07));
ADCSRA |= 1<<ADSC; // Start conversion
#endif
#ifdef ULTIPANEL
buttons_check();
#endif
temp_state = 5;
break;
case 5: // Measure TEMP_2
#if (TEMP_2_PIN > -1)
raw_temp_2_value += ADC;
#endif
temp_state = 0;
temp_count++;
break;
#if (TEMP_2_PIN > -1)
raw_temp_2_value += ADC;
#endif
temp_state = 0;
temp_count++;
break;
default:
SERIAL_ERRORLN("Temp measurement error!");
break;
SERIAL_ERRORLN("Temp measurement error!");
break;
}
if(temp_count >= 16) // 6 ms * 16 = 96ms.
@ -472,67 +473,71 @@ ISR(TIMER0_COMPB_vect)
raw_temp_0_value = 0;
raw_temp_1_value = 0;
raw_temp_2_value = 0;
#ifdef HEATER_0_MAXTEMP
#if (HEATER_0_PIN > -1)
if(current_raw[TEMPSENSOR_HOTEND_0] >= maxttemp_0) {
target_raw[TEMPSENSOR_HOTEND_0] = 0;
analogWrite(HEATER_0_PIN, 0);
SERIAL_ERRORLN("Temperature extruder 0 switched off. MAXTEMP triggered !!");
kill();
}
#ifdef HEATER_0_MAXTEMP
#if (HEATER_0_PIN > -1)
if(current_raw[TEMPSENSOR_HOTEND_0] >= maxttemp_0) {
target_raw[TEMPSENSOR_HOTEND_0] = 0;
analogWrite(HEATER_0_PIN, 0);
SERIAL_ERRORLN("Temperature extruder 0 switched off. MAXTEMP triggered !!");
kill();
}
#endif
#endif
#ifdef HEATER_1_MAXTEMP
#if (HEATER_1_PIN > -1)
if(current_raw[TEMPSENSOR_HOTEND_1] >= maxttemp_1) {
target_raw[TEMPSENSOR_HOTEND_1] = 0;
if(current_raw[2] >= maxttemp_1) {
analogWrite(HEATER_2_PIN, 0);
SERIAL_ERRORLN("Temperature extruder 1 switched off. MAXTEMP triggered !!");
kill()
}
#endif
#endif //MAXTEMP
#ifdef HEATER_0_MINTEMP
#if (HEATER_0_PIN > -1)
if(current_raw[TEMPSENSOR_HOTEND_0] <= minttemp_0) {
target_raw[TEMPSENSOR_HOTEND_0] = 0;
analogWrite(HEATER_0_PIN, 0);
SERIAL_ERRORLN("Temperature extruder 0 switched off. MINTEMP triggered !!");
kill();
}
#endif
#endif
#endif
#ifdef HEATER_1_MAXTEMP
#if (HEATER_1_PIN > -1)
if(current_raw[TEMPSENSOR_HOTEND_1] >= maxttemp_1) {
target_raw[TEMPSENSOR_HOTEND_1] = 0;
if(current_raw[2] >= maxttemp_1) {
analogWrite(HEATER_2_PIN, 0);
SERIAL_ERRORLN("Temperature extruder 1 switched off. MAXTEMP triggered !!");
kill()
}
#ifdef HEATER_1_MINTEMP
#if (HEATER_2_PIN > -1)
if(current_raw[TEMPSENSOR_HOTEND_1] <= minttemp_1) {
target_raw[TEMPSENSOR_HOTEND_1] = 0;
analogWrite(HEATER_2_PIN, 0);
SERIAL_ERRORLN("Temperature extruder 1 switched off. MINTEMP triggered !!");
kill();
}
#endif
#endif //MAXTEMP
#ifdef BED_MINTEMP
#if (HEATER_1_PIN > -1)
if(current_raw[1] <= bed_minttemp) {
target_raw[1] = 0;
WRITE(HEATER_1_PIN, 0);
SERIAL_ERRORLN("Temperatur heated bed switched off. MINTEMP triggered !!");
kill();
}
#endif
#endif
#endif //MAXTEMP
#ifdef HEATER_0_MINTEMP
#if (HEATER_0_PIN > -1)
if(current_raw[TEMPSENSOR_HOTEND_0] <= minttemp_0) {
target_raw[TEMPSENSOR_HOTEND_0] = 0;
analogWrite(HEATER_0_PIN, 0);
SERIAL_ERRORLN("Temperature extruder 0 switched off. MINTEMP triggered !!");
kill();
}
#ifdef BED_MAXTEMP
#if (HEATER_1_PIN > -1)
if(current_raw[1] >= bed_maxttemp) {
target_raw[1] = 0;
WRITE(HEATER_1_PIN, 0);
SERIAL_ERRORLN("Temperature heated bed switched off. MAXTEMP triggered !!");
kill();
}
#endif
#endif
#endif
#ifdef HEATER_1_MINTEMP
#if (HEATER_2_PIN > -1)
if(current_raw[TEMPSENSOR_HOTEND_1] <= minttemp_1) {
target_raw[TEMPSENSOR_HOTEND_1] = 0;
analogWrite(HEATER_2_PIN, 0);
SERIAL_ERRORLN("Temperature extruder 1 switched off. MINTEMP triggered !!");
kill();
}
#endif
#endif //MAXTEMP
#ifdef BED_MINTEMP
#if (HEATER_1_PIN > -1)
if(current_raw[1] <= bed_minttemp) {
target_raw[1] = 0;
WRITE(HEATER_1_PIN, 0);
SERIAL_ERRORLN("Temperatur heated bed switched off. MINTEMP triggered !!");
kill();
}
#endif
#endif
#ifdef BED_MAXTEMP
#if (HEATER_1_PIN > -1)
if(current_raw[1] >= bed_maxttemp) {
target_raw[1] = 0;
WRITE(HEATER_1_PIN, 0);
SERIAL_ERRORLN("Temperature heated bed switched off. MAXTEMP triggered !!");
kill();
}
#endif
#endif
}
}

21
Marlin/temperature.h
Unescape Escape View File

@ -27,9 +27,11 @@
#include "stepper.h"
#endif
// public functions
void tp_init(); //initialise the heating
void manage_heater(); //it is critical that this is called periodically.
enum TempSensor {TEMPSENSOR_HOTEND_0=0,TEMPSENSOR_BED=1, TEMPSENSOR_HOTEND_1=2};
//low leven conversion routines
@ -41,9 +43,11 @@ float analog2tempBed(int raw);
extern int target_raw[3];
extern int current_raw[3];
extern float Kp,Ki,Kd,Kc;
#ifdef PIDTEMP
extern float pid_setpoint ;
#endif
#ifdef WATCHPERIOD
extern int watch_raw[3] ;
extern unsigned long watchmillis;
@ -63,15 +67,15 @@ inline float degTargetHotend0() { return analog2temp(target_raw[TEMPSENSOR_HOTE
inline float degTargetHotend1() { return analog2temp(target_raw[TEMPSENSOR_HOTEND_1]);};
inline float degTargetBed() { return analog2tempBed(target_raw[TEMPSENSOR_BED]);};
inline void setTargetHotend0(float celsius)
inline void setTargetHotend0(const float &celsius)
{
target_raw[TEMPSENSOR_HOTEND_0]=temp2analog(celsius);
#ifdef PIDTEMP
pid_setpoint = celsius;
#endif //PIDTEMP
};
inline void setTargetHotend1(float celsius) { target_raw[TEMPSENSOR_HOTEND_1]=temp2analog(celsius);};
inline void setTargetBed(float celsius) { target_raw[TEMPSENSOR_BED ]=temp2analogBed(celsius);};
inline void setTargetHotend1(const float &celsius) { target_raw[TEMPSENSOR_HOTEND_1]=temp2analog(celsius);};
inline void setTargetBed(const float &celsius) { target_raw[TEMPSENSOR_BED ]=temp2analogBed(celsius);};
inline bool isHeatingHotend0() {return target_raw[TEMPSENSOR_HOTEND_0] > current_raw[TEMPSENSOR_HOTEND_0];};
inline bool isHeatingHotend1() {return target_raw[TEMPSENSOR_HOTEND_1] > current_raw[TEMPSENSOR_HOTEND_1];};
@ -84,16 +88,5 @@ inline bool isCoolingBed() {return target_raw[TEMPSENSOR_BED] < current_raw[TEMP
void disable_heater();
void setWatch();
#ifdef HEATER_0_USES_THERMISTOR
#define HEATERSOURCE 1
#endif
#ifdef BED_USES_THERMISTOR
#define BEDSOURCE 1
#endif
#endif

126
Marlin/ultralcd.h
Unescape Escape View File

@ -9,107 +9,48 @@
void lcd_status(const char* message);
void beep();
void buttons_check();
#define LCDSTATUSRIGHT
#define LCD_UPDATE_INTERVAL 100
#define STATUSTIMEOUT 15000
#include "Configuration.h"
#include <LiquidCrystal.h>
extern LiquidCrystal lcd;
//lcd display size
#ifdef NEWPANEL
//arduino pin witch triggers an piezzo beeper
#define BEEPER 18
#ifdef NEWPANEL
#define LCD_PINS_RS 20
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 16
#define LCD_PINS_D5 21
#define LCD_PINS_D6 5
#define LCD_PINS_D7 6
//buttons are directly attached
#define BTN_EN1 40
#define BTN_EN2 42
#define BTN_ENC 19 //the click
#define BLEN_C 2
#define BLEN_B 1
#define BLEN_A 0
#define SDCARDDETECT 38
#define EN_C (1<<BLEN_C)
#define EN_B (1<<BLEN_B)
#define EN_A (1<<BLEN_A)
//encoder rotation values
#define encrot0 0
#define encrot1 2
#define encrot2 3
#define encrot3 1
#define EN_C (1<<BLEN_C)
#define EN_B (1<<BLEN_B)
#define EN_A (1<<BLEN_A)
#define CLICKED (buttons&EN_C)
#define BLOCK {blocking=millis()+blocktime;}
#define CARDINSERTED (READ(SDCARDDETECT)==0)
#else
#define CLICKED (buttons&EN_C)
#define BLOCK {blocking=millis()+blocktime;}
#define CARDINSERTED (READ(SDCARDDETECT)==0)
#else
//arduino pin witch triggers an piezzo beeper
#define BEEPER 18
//buttons are attached to a shift register
#define SHIFT_CLK 38
#define SHIFT_LD 42
#define SHIFT_OUT 40
#define SHIFT_EN 17
#define LCD_PINS_RS 16
#define LCD_PINS_ENABLE 5
#define LCD_PINS_D4 6
#define LCD_PINS_D5 21
#define LCD_PINS_D6 20
#define LCD_PINS_D7 19
//bits in the shift register that carry the buttons for:
// left up center down right red
#define BL_LE 7
#define BL_UP 6
#define BL_MI 5
#define BL_DW 4
#define BL_RI 3
#define BL_ST 2
#define BLEN_B 1
#define BLEN_A 0
//encoder rotation values
#define encrot0 0
#define encrot1 2
#define encrot2 3
#define encrot3 1
//atomatic, do not change
#define B_LE (1<<BL_LE)
#define B_UP (1<<BL_UP)
#define B_MI (1<<BL_MI)
#define B_DW (1<<BL_DW)
#define B_RI (1<<BL_RI)
#define B_ST (1<<BL_ST)
#define EN_B (1<<BLEN_B)
#define EN_A (1<<BLEN_A)
#define CLICKED ((buttons&B_MI)||(buttons&B_ST))
#define BLOCK {blocking[BL_MI]=millis()+blocktime;blocking[BL_ST]=millis()+blocktime;}
#endif
//atomatic, do not change
#define B_LE (1<<BL_LE)
#define B_UP (1<<BL_UP)
#define B_MI (1<<BL_MI)
#define B_DW (1<<BL_DW)
#define B_RI (1<<BL_RI)
#define B_ST (1<<BL_ST)
#define EN_B (1<<BLEN_B)
#define EN_A (1<<BLEN_A)
#define CLICKED ((buttons&B_MI)||(buttons&B_ST))
#define BLOCK {blocking[BL_MI]=millis()+blocktime;blocking[BL_ST]=millis()+blocktime;}
#endif
// blocking time for recognizing a new keypress of one key, ms
#define blocktime 500
#define lcdslow 5
#define blocktime 500
#define lcdslow 5
enum MainStatus{Main_Status, Main_Menu, Main_Prepare, Main_Control, Main_SD};
class MainMenu{
@ -134,6 +75,7 @@
bool linechanging;
};
//conversion routines, could need some overworking
char *fillto(int8_t n,char *c);
char *ftostr51(const float &x);
char *ftostr31(const float &x);
@ -146,11 +88,15 @@
#else //no lcd
#define LCD_STATUS
#define LCD_MESSAGE(x)
inline void lcd_status() {};
#endif
#ifndef ULTIPANEL
#define CLICKED false
#define BLOCK ;
#define BLOCK ;
#endif
#endif //ULTRALCD

199
Marlin/ultralcd.pde
Unescape Escape View File

@ -1,7 +1,7 @@
#include "ultralcd.h"
#ifdef ULTRA_LCD
extern volatile int feedmultiply;
extern long position[4];
@ -122,58 +122,57 @@ void lcd_status()
menu.update();
}
#ifdef ULTIPANEL
void buttons_init()
{
#ifdef NEWPANEL
pinMode(BTN_EN1,INPUT);
pinMode(BTN_EN2,INPUT);
pinMode(BTN_ENC,INPUT);
pinMode(SDCARDDETECT,INPUT);
WRITE(BTN_EN1,HIGH);
WRITE(BTN_EN2,HIGH);
WRITE(BTN_ENC,HIGH);
WRITE(SDCARDDETECT,HIGH);
#else
pinMode(SHIFT_CLK,OUTPUT);
pinMode(SHIFT_LD,OUTPUT);
pinMode(SHIFT_EN,OUTPUT);
pinMode(SHIFT_OUT,INPUT);
WRITE(SHIFT_OUT,HIGH);
WRITE(SHIFT_LD,HIGH);
WRITE(SHIFT_EN,LOW);
#endif
#ifdef NEWPANEL
pinMode(BTN_EN1,INPUT);
pinMode(BTN_EN2,INPUT);
pinMode(BTN_ENC,INPUT);
pinMode(SDCARDDETECT,INPUT);
WRITE(BTN_EN1,HIGH);
WRITE(BTN_EN2,HIGH);
WRITE(BTN_ENC,HIGH);
WRITE(SDCARDDETECT,HIGH);
#else
pinMode(SHIFT_CLK,OUTPUT);
pinMode(SHIFT_LD,OUTPUT);
pinMode(SHIFT_EN,OUTPUT);
pinMode(SHIFT_OUT,INPUT);
WRITE(SHIFT_OUT,HIGH);
WRITE(SHIFT_LD,HIGH);
WRITE(SHIFT_EN,LOW);
#endif
}
void buttons_check()
{
// volatile static bool busy=false;
// if(busy)
// return;
// busy=true;
#ifdef NEWPANEL
uint8_t newbutton=0;
if(READ(BTN_EN1)==0) newbutton|=EN_A;
if(READ(BTN_EN2)==0) newbutton|=EN_B;
if((blocking<millis()) &&(READ(BTN_ENC)==0))
newbutton|=EN_C;
buttons=newbutton;
#else //read it from the shift register
uint8_t newbutton=0;
WRITE(SHIFT_LD,LOW);
WRITE(SHIFT_LD,HIGH);
unsigned char tmp_buttons=0;
for(unsigned char i=0;i<8;i++)
{
newbutton = newbutton>>1;
if(READ(SHIFT_OUT))
newbutton|=(1<<7);
WRITE(SHIFT_CLK,HIGH);
WRITE(SHIFT_CLK,LOW);
}
buttons=~newbutton; //invert it, because a pressed switch produces a logical 0
#endif
#ifdef NEWPANEL
uint8_t newbutton=0;
if(READ(BTN_EN1)==0) newbutton|=EN_A;
if(READ(BTN_EN2)==0) newbutton|=EN_B;
if((blocking<millis()) &&(READ(BTN_ENC)==0))
newbutton|=EN_C;
buttons=newbutton;
#else //read it from the shift register
uint8_t newbutton=0;
WRITE(SHIFT_LD,LOW);
WRITE(SHIFT_LD,HIGH);
unsigned char tmp_buttons=0;
for(unsigned char i=0;i<8;i++)
{
newbutton = newbutton>>1;
if(READ(SHIFT_OUT))
newbutton|=(1<<7);
WRITE(SHIFT_CLK,HIGH);
WRITE(SHIFT_CLK,LOW);
}
buttons=~newbutton; //invert it, because a pressed switch produces a logical 0
#endif
char enc=0;
if(buttons&EN_A)
enc|=(1<<0);
@ -212,7 +211,6 @@ void buttons_check()
}
}
lastenc=enc;
// busy=false;
}
#endif
@ -223,9 +221,9 @@ MainMenu::MainMenu()
displayStartingRow=0;
activeline=0;
force_lcd_update=true;
#ifdef ULTIPANEL
buttons_init();
#endif
#ifdef ULTIPANEL
buttons_init();
#endif
lcd_init();
linechanging=false;
}
@ -1154,12 +1152,13 @@ uint8_t getnrfilenames()
cnt++;
}
return cnt;
#else
return 0;
#endif
}
void MainMenu::showSD()
{
#ifdef SDSUPPORT
uint8_t line=0;
@ -1205,11 +1204,11 @@ void MainMenu::showSD()
if(force_lcd_update)
{
lcd.setCursor(0,line);
#ifdef CARDINSERTED
#ifdef CARDINSERTED
if(CARDINSERTED)
#else
#else
if(true)
#endif
#endif
{
lcd.print(" \004Refresh");
}
@ -1306,9 +1305,9 @@ void MainMenu::showMainMenu()
{
//if(int(encoderpos/lcdslow)!=int(lastencoderpos/lcdslow))
// force_lcd_update=true;
#ifndef ULTIPANEL
force_lcd_update=false;
#endif
#ifndef ULTIPANEL
force_lcd_update=false;
#endif
//Serial.println((int)activeline);
if(force_lcd_update)
clear();
@ -1347,17 +1346,17 @@ void MainMenu::showMainMenu()
beepshort();
}
}break;
#ifdef SDSUPPORT
#ifdef SDSUPPORT
case ItemM_file:
{
if(force_lcd_update)
{
lcd.setCursor(0,line);
#ifdef CARDINSERTED
if(CARDINSERTED)
#else
if(true)
#endif
#ifdef CARDINSERTED
if(CARDINSERTED)
#else
if(true)
#endif
{
if(sdmode)
lcd.print(" Stop Print \x7E");
@ -1370,7 +1369,7 @@ void MainMenu::showMainMenu()
}
}
#ifdef CARDINSERTED
if(CARDINSERTED)
if(CARDINSERTED)
#endif
if((activeline==line)&&CLICKED)
{
@ -1380,28 +1379,30 @@ void MainMenu::showMainMenu()
beepshort();
}
}break;
#endif
#endif
default:
SERIAL_ERRORLN("Something is wrong in the MenuStructure.");
break;
}
}
if(activeline<0) activeline=0;
if(activeline>=LCD_HEIGHT) activeline=LCD_HEIGHT-1;
if(activeline<0)
activeline=0;
if(activeline>=LCD_HEIGHT)
activeline=LCD_HEIGHT-1;
if((encoderpos!=lastencoderpos)||force_lcd_update)
{
lcd.setCursor(0,activeline);lcd.print(activeline?' ':' ');
if(encoderpos<0) encoderpos=0;
if(encoderpos>3*lcdslow) encoderpos=3*lcdslow;
if(encoderpos>3*lcdslow)
encoderpos=3*lcdslow;
activeline=abs(encoderpos/lcdslow)%LCD_HEIGHT;
if(activeline<0) activeline=0;
if(activeline>=LCD_HEIGHT) activeline=LCD_HEIGHT-1;
if(activeline<0)
activeline=0;
if(activeline>=LCD_HEIGHT)
activeline=LCD_HEIGHT-1;
lastencoderpos=encoderpos;
lcd.setCursor(0,activeline);lcd.print(activeline?'>':'\003');
}
}
void MainMenu::update()
@ -1409,25 +1410,24 @@ void MainMenu::update()
static MainStatus oldstatus=Main_Menu; //init automatically causes foce_lcd_update=true
static long timeoutToStatus=0;
static bool oldcardstatus=false;
#ifdef CARDINSERTED
if((CARDINSERTED != oldcardstatus))
{
force_lcd_update=true;
oldcardstatus=CARDINSERTED;
//Serial.println("echo: SD CHANGE");
if(CARDINSERTED)
#ifdef CARDINSERTED
if((CARDINSERTED != oldcardstatus))
{
initsd();
lcd_status("Card inserted");
force_lcd_update=true;
oldcardstatus=CARDINSERTED;
//Serial.println("echo: SD CHANGE");
if(CARDINSERTED)
{
initsd();
lcd_status("Card inserted");
}
else
{
sdactive=false;
lcd_status("Card removed");
}
}
else
{
sdactive=false;
lcd_status("Card removed");
}
}
#endif
#endif
if(status!=oldstatus)
{
@ -1484,9 +1484,9 @@ void MainMenu::update()
//return for string conversion routines
char conv[8];
static char conv[8];
/// convert float to string with +123.4 format
// convert float to string with +123.4 format
char *ftostr3(const float &x)
{
//sprintf(conv,"%5.1f",x);
@ -1497,6 +1497,7 @@ char *ftostr3(const float &x)
conv[3]=0;
return conv;
}
char *itostr2(const uint8_t &x)
{
//sprintf(conv,"%5.1f",x);
@ -1506,10 +1507,10 @@ char *itostr2(const uint8_t &x)
conv[2]=0;
return conv;
}
/// convert float to string with +123.4 format
// convert float to string with +123.4 format
char *ftostr31(const float &x)
{
//sprintf(conv,"%5.1f",x);
int xx=x*10;
conv[0]=(xx>=0)?'+':'-';
xx=abs(xx);
@ -1524,7 +1525,6 @@ char *ftostr31(const float &x)
char *itostr31(const int &xx)
{
//sprintf(conv,"%5.1f",x);
conv[0]=(xx>=0)?'+':'-';
conv[1]=(xx/1000)%10+'0';
conv[2]=(xx/100)%10+'0';
@ -1534,6 +1534,7 @@ char *itostr31(const int &xx)
conv[6]=0;
return conv;
}
char *itostr3(const int &xx)
{
conv[0]=(xx/100)%10+'0';
@ -1553,7 +1554,7 @@ char *itostr4(const int &xx)
return conv;
}
/// convert float to string with +1234.5 format
// convert float to string with +1234.5 format
char *ftostr51(const float &x)
{
int xx=x*10;
@ -1587,11 +1588,9 @@ char *fillto(int8_t n,char *c)
}
ret[n]=0;
return ret;
}
#else
inline void lcd_status() {};
#endif
#endif //ULTRA_LCD

15
Marlin/watchdog.h
Unescape Escape View File

@ -1,13 +1,16 @@
#ifndef __WATCHDOGH
#define __WATCHDOGH
#include "Configuration.h"
//#ifdef USE_WATCHDOG
#ifdef USE_WATCHDOG
/// intialise watch dog with a 1 sec interrupt time
void wd_init();
/// pad the dog/reset watchdog. MUST be called at least every second after the first wd_init or avr will go into emergency procedures..
void wd_reset();
// intialise watch dog with a 1 sec interrupt time
void wd_init();
// pad the dog/reset watchdog. MUST be called at least every second after the first wd_init or avr will go into emergency procedures..
void wd_reset();
//#endif
#else
inline void wd_init() {};
inline void wd_reset() {};
#endif
#endif

2
Marlin/watchdog.pde
Unescape Escape View File

@ -3,7 +3,7 @@
#include <avr/wdt.h>
#include <avr/interrupt.h>
volatile uint8_t timeout_seconds=0;
static volatile uint8_t timeout_seconds=0;
void(* ctrlaltdelete) (void) = 0; //does not work on my atmega2560

Write Preview
Loading…
Cancel
Save