melch
/
Marlin
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity

✨ WYH L12864 LCD (Alfawise Ex8) (#22863)

Browse Source
x301
VragVideo 3 years ago committed by Scott Lahteine
parent 58a26fcaac
commit 0273a68587
56 changed files with 181 additions and 101 deletions
Show Stats Download Patch File Download Diff File

5
Marlin/Configuration.h
Unescape Escape View File

@ -2375,6 +2375,11 @@
//#define VIKI2 //#define VIKI2
//#define miniVIKI //#define miniVIKI
//
// Alfawise Ex8 printer LCD marked as WYH L12864 COG
//
//#define WYH_L12864
// //
// MakerLab Mini Panel with graphic // MakerLab Mini Panel with graphic
// controller and SD support - https://reprap.org/wiki/Mini_panel // controller and SD support - https://reprap.org/wiki/Mini_panel

2
Marlin/Configuration_adv.h
Unescape Escape View File

@ -1603,7 +1603,7 @@
* Set STATUS_EXPIRE_SECONDS to zero to never clear the status. * Set STATUS_EXPIRE_SECONDS to zero to never clear the status.
* This will prevent position updates from being displayed. * This will prevent position updates from being displayed.
*/ */
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
// Enable this option and reduce the value to optimize screen updates. // Enable this option and reduce the value to optimize screen updates.
// The normal delay is 10µs. Use the lowest value that still gives a reliable display. // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
//#define DOGM_SPI_DELAY_US 5 //#define DOGM_SPI_DELAY_US 5

4
Marlin/src/HAL/DUE/dogm/u8g_com_HAL_DUE_st7920_sw_spi.cpp
Unescape Escape View File

@ -57,7 +57,7 @@
#include "../../../inc/MarlinConfigPre.h" #include "../../../inc/MarlinConfigPre.h"
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#include "../../../inc/MarlinConfig.h" #include "../../../inc/MarlinConfig.h"
#include "../../shared/Delay.h" #include "../../shared/Delay.h"
@ -182,5 +182,5 @@ uint8_t u8g_com_HAL_DUE_ST7920_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_va
} }
#endif // LIGHTWEIGHT_UI #endif // LIGHTWEIGHT_UI
#endif // U8GLIB_ST7920 #endif // IS_U8GLIB_ST7920
#endif // ARDUINO_ARCH_SAM #endif // ARDUINO_ARCH_SAM

4
Marlin/src/HAL/DUE/dogm/u8g_com_HAL_DUE_sw_spi.cpp
Unescape Escape View File

@ -57,7 +57,7 @@
#include "../../../inc/MarlinConfigPre.h" #include "../../../inc/MarlinConfigPre.h"
#if HAS_MARLINUI_U8GLIB && DISABLED(U8GLIB_ST7920) #if HAS_MARLINUI_U8GLIB && !IS_U8GLIB_ST7920
#include "u8g_com_HAL_DUE_sw_spi_shared.h" #include "u8g_com_HAL_DUE_sw_spi_shared.h"
@ -141,5 +141,5 @@ uint8_t u8g_com_HAL_DUE_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void
return 1; return 1;
} }
#endif // HAS_MARLINUI_U8GLIB && !U8GLIB_ST7920 #endif // HAS_MARLINUI_U8GLIB && !IS_U8GLIB_ST7920
#endif // ARDUINO_ARCH_SAM #endif // ARDUINO_ARCH_SAM

4
Marlin/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_st7920_sw_spi.cpp
Unescape Escape View File

@ -57,7 +57,7 @@
#include "../../../inc/MarlinConfigPre.h" #include "../../../inc/MarlinConfigPre.h"
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#include <U8glib-HAL.h> #include <U8glib-HAL.h>
#include <SoftwareSPI.h> #include <SoftwareSPI.h>
@ -143,5 +143,5 @@ uint8_t u8g_com_HAL_LPC1768_ST7920_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t ar
return 1; return 1;
} }
#endif // U8GLIB_ST7920 #endif // IS_U8GLIB_ST7920
#endif // TARGET_LPC1768 #endif // TARGET_LPC1768

4
Marlin/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_sw_spi.cpp
Unescape Escape View File

@ -57,7 +57,7 @@
#include "../../../inc/MarlinConfigPre.h" #include "../../../inc/MarlinConfigPre.h"
#if HAS_MARLINUI_U8GLIB && DISABLED(U8GLIB_ST7920) #if HAS_MARLINUI_U8GLIB && !IS_U8GLIB_ST7920
#include <SoftwareSPI.h> #include <SoftwareSPI.h>
#include "../../shared/HAL_SPI.h" #include "../../shared/HAL_SPI.h"
@ -205,5 +205,5 @@ uint8_t u8g_com_HAL_LPC1768_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val,
return 1; return 1;
} }
#endif // HAS_MARLINUI_U8GLIB && !U8GLIB_ST7920 #endif // HAS_MARLINUI_U8GLIB && !IS_U8GLIB_ST7920
#endif // TARGET_LPC1768 #endif // TARGET_LPC1768

4
Marlin/src/HAL/NATIVE_SIM/u8g/u8g_com_st7920_sw_spi.cpp
Unescape Escape View File

@ -57,7 +57,7 @@
#include "../../../inc/MarlinConfig.h" #include "../../../inc/MarlinConfig.h"
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#include <U8glib-HAL.h> #include <U8glib-HAL.h>
#include "../../shared/Delay.h" #include "../../shared/Delay.h"
@ -167,5 +167,5 @@ uint8_t u8g_com_ST7920_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void
} }
#endif #endif
#endif // U8GLIB_ST7920 #endif // IS_U8GLIB_ST7920
#endif // TARGET_LPC1768 #endif // TARGET_LPC1768

4
Marlin/src/HAL/NATIVE_SIM/u8g/u8g_com_sw_spi.cpp
Unescape Escape View File

@ -57,7 +57,7 @@
#include "../../../inc/MarlinConfig.h" #include "../../../inc/MarlinConfig.h"
#if HAS_MARLINUI_U8GLIB && DISABLED(U8GLIB_ST7920) #if HAS_MARLINUI_U8GLIB && !IS_U8GLIB_ST7920
#undef SPI_SPEED #undef SPI_SPEED
#define SPI_SPEED 2 // About 2 MHz #define SPI_SPEED 2 // About 2 MHz
@ -211,5 +211,5 @@ uint8_t u8g_com_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_pt
#elif !ANY(TFT_COLOR_UI, TFT_CLASSIC_UI, TFT_LVGL_UI, HAS_MARLINUI_HD44780) && HAS_MARLINUI_U8GLIB #elif !ANY(TFT_COLOR_UI, TFT_CLASSIC_UI, TFT_LVGL_UI, HAS_MARLINUI_HD44780) && HAS_MARLINUI_U8GLIB
#include <U8glib-HAL.h> #include <U8glib-HAL.h>
uint8_t u8g_com_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr) {return 0;} uint8_t u8g_com_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr) {return 0;}
#endif // HAS_MARLINUI_U8GLIB && !U8GLIB_ST7920 #endif // HAS_MARLINUI_U8GLIB && !IS_U8GLIB_ST7920
#endif // __PLAT_NATIVE_SIM__ #endif // __PLAT_NATIVE_SIM__

79
Marlin/src/inc/Conditionals_LCD.h
Unescape Escape View File

@ -39,17 +39,17 @@
/** /**
* General Flags that may be set below by specific LCDs * General Flags that may be set below by specific LCDs
* *
* DOGLCD : Run a Graphical LCD through U8GLib (with MarlinUI) * DOGLCD : Run a Graphical LCD through U8GLib (with MarlinUI)
* IS_ULTIPANEL : Define LCD_PINS_D5/6/7 for direct-connected "Ultipanel" LCDs * IS_ULTIPANEL : Define LCD_PINS_D5/6/7 for direct-connected "Ultipanel" LCDs
* IS_ULTRA_LCD : Ultra LCD, not necessarily Ultipanel. * IS_ULTRA_LCD : Ultra LCD, not necessarily Ultipanel.
* IS_RRD_SC : Common RRD Smart Controller digital interface pins * IS_RRD_SC : Common RRD Smart Controller digital interface pins
* IS_RRD_FG_SC : Common RRD Full Graphical Smart Controller digital interface pins * IS_RRD_FG_SC : Common RRD Full Graphical Smart Controller digital interface pins
* U8GLIB_ST7920 : Most common DOGM display SPI interface, supporting a "lightweight" display mode. * IS_U8GLIB_ST7920 : Most common DOGM display SPI interface, supporting a "lightweight" display mode.
* U8GLIB_SH1106 : SH1106 OLED with I2C interface via U8GLib * U8GLIB_SH1106 : SH1106 OLED with I2C interface via U8GLib
* IS_U8GLIB_SSD1306 : SSD1306 OLED with I2C interface via U8GLib * IS_U8GLIB_SSD1306 : SSD1306 OLED with I2C interface via U8GLib (U8GLIB_SSD1306)
* U8GLIB_SSD1309 : SSD1309 OLED with I2C interface via U8GLib * U8GLIB_SSD1309 : SSD1309 OLED with I2C interface via U8GLib (HAS_U8GLIB_I2C_OLED, IS_ULTRA_LCD, DOGLCD)
* U8GLIB_ST7565_64128N : ST7565 128x64 LCD with SPI interface via U8GLib * IS_U8GLIB_ST7565_64128N : ST7565 128x64 LCD with SPI interface via U8GLib
* U8GLIB_LM6059_AF : LM6059 with Hardware SPI via U8GLib * IS_U8GLIB_LM6059_AF : LM6059 with Hardware SPI via U8GLib
*/ */
#if EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY) #if EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY)
@ -85,7 +85,7 @@
#elif ENABLED(ZONESTAR_12864LCD) #elif ENABLED(ZONESTAR_12864LCD)
#define DOGLCD #define DOGLCD
#define IS_RRD_SC 1 #define IS_RRD_SC 1
#define U8GLIB_ST7920 #define IS_U8GLIB_ST7920 1
#elif ENABLED(ZONESTAR_12864OLED) #elif ENABLED(ZONESTAR_12864OLED)
#define IS_RRD_SC 1 #define IS_RRD_SC 1
@ -99,19 +99,24 @@
#define IS_ULTIPANEL 1 #define IS_ULTIPANEL 1
#define ENCODER_PULSES_PER_STEP 2 #define ENCODER_PULSES_PER_STEP 2
#elif ANY(miniVIKI, VIKI2, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864) #elif ANY(miniVIKI, VIKI2, WYH_L12864, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864)
#define IS_DOGM_12864 1
#define DOGLCD #define DOGLCD
#define IS_ULTIPANEL 1 #define IS_ULTIPANEL 1
#if ENABLED(miniVIKI) #if ENABLED(miniVIKI)
#define U8GLIB_ST7565_64128N #define IS_U8GLIB_ST7565_64128N 1
#elif ENABLED(VIKI2) #elif ENABLED(VIKI2)
#define U8GLIB_ST7565_64128N #define IS_U8GLIB_ST7565_64128N 1
#elif ENABLED(WYH_L12864)
#define IS_U8GLIB_ST7565_64128N 1
#define ST7565_XOFFSET 0x04
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#define U8GLIB_LM6059_AF #define IS_U8GLIB_LM6059_AF 1
#elif ENABLED(AZSMZ_12864) #elif ENABLED(AZSMZ_12864)
#define U8GLIB_ST7565_64128N #define IS_U8GLIB_ST7565_64128N 1
#endif #endif
#elif ENABLED(OLED_PANEL_TINYBOY2) #elif ENABLED(OLED_PANEL_TINYBOY2)
@ -128,7 +133,7 @@
#elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD) #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#define DOGLCD #define DOGLCD
#define U8GLIB_ST7920 #define IS_U8GLIB_ST7920 1
#define IS_ULTIPANEL 1 #define IS_ULTIPANEL 1
#elif ENABLED(MKS_12864OLED) #elif ENABLED(MKS_12864OLED)
@ -144,7 +149,7 @@
#elif ENABLED(SAV_3DGLCD) #elif ENABLED(SAV_3DGLCD)
#ifdef U8GLIB_SSD1306 #ifdef U8GLIB_SSD1306
#define IS_U8GLIB_SSD1306 #define IS_U8GLIB_SSD1306 // Allow for U8GLIB_SSD1306 + SAV_3DGLCD
#endif #endif
#define IS_NEWPANEL 1 #define IS_NEWPANEL 1
@ -266,7 +271,7 @@
// ST7920-based graphical displays // ST7920-based graphical displays
#if ANY(IS_RRD_FG_SC, LCD_FOR_MELZI, SILVER_GATE_GLCD_CONTROLLER) #if ANY(IS_RRD_FG_SC, LCD_FOR_MELZI, SILVER_GATE_GLCD_CONTROLLER)
#define DOGLCD #define DOGLCD
#define U8GLIB_ST7920 #define IS_U8GLIB_ST7920 1
#define IS_RRD_SC 1 #define IS_RRD_SC 1
#endif #endif
@ -275,7 +280,7 @@
#define IS_ULTIPANEL 1 #define IS_ULTIPANEL 1
#define DOGLCD #define DOGLCD
#if ENABLED(MAKRPANEL) #if ENABLED(MAKRPANEL)
#define U8GLIB_ST7565_64128N #define IS_U8GLIB_ST7565_64128N 1
#endif #endif
#endif #endif
@ -372,25 +377,28 @@
* I2C Panels * I2C Panels
*/ */
#if EITHER(LCD_SAINSMART_I2C_1602, LCD_SAINSMART_I2C_2004) #if ANY(IS_RRD_SC, IS_DOGM_12864, OLED_PANEL_TINYBOY2, LCD_I2C_PANELOLU2)
#define LCD_I2C_TYPE_PCF8575 #define STD_ENCODER_PULSES_PER_STEP 4
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander #define STD_ENCODER_STEPS_PER_MENU_ITEM 1
#if ENABLED(LCD_I2C_PANELOLU2) // PANELOLU2 LCD with status LEDs, separate encoder and click inputs
#define LCD_I2C_TYPE_MCP23017 // I2C Character-based 12864 display
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
#define LCD_USE_I2C_BUZZER // Enable buzzer on LCD (optional)
#define IS_ULTIPANEL 1
#endif
#elif EITHER(LCD_SAINSMART_I2C_1602, LCD_SAINSMART_I2C_2004)
#define LCD_I2C_TYPE_PCF8575 // I2C Character-based 12864 display
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
#if ENABLED(LCD_SAINSMART_I2C_2004) #if ENABLED(LCD_SAINSMART_I2C_2004)
#define LCD_WIDTH 20 #define LCD_WIDTH 20
#define LCD_HEIGHT 4 #define LCD_HEIGHT 4
#endif #endif
#elif ENABLED(LCD_I2C_PANELOLU2)
// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
#define LCD_I2C_TYPE_MCP23017
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
#define LCD_USE_I2C_BUZZER // Enable buzzer on LCD (optional)
#define IS_ULTIPANEL 1
#elif ENABLED(LCD_I2C_VIKI) #elif ENABLED(LCD_I2C_VIKI)
/** /**
@ -416,11 +424,6 @@
#define STD_ENCODER_PULSES_PER_STEP 2 #define STD_ENCODER_PULSES_PER_STEP 2
#define STD_ENCODER_STEPS_PER_MENU_ITEM 1 #define STD_ENCODER_STEPS_PER_MENU_ITEM 1
#elif ANY(IS_RRD_SC, miniVIKI, VIKI2, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864, OLED_PANEL_TINYBOY2, BQ_LCD_SMART_CONTROLLER, LCD_I2C_PANELOLU2)
#define STD_ENCODER_PULSES_PER_STEP 4
#define STD_ENCODER_STEPS_PER_MENU_ITEM 1
#endif #endif
#if EITHER(LCD_I2C_TYPE_MCP23017, LCD_I2C_TYPE_MCP23008) && DISABLED(NO_LCD_DETECT) #if EITHER(LCD_I2C_TYPE_MCP23017, LCD_I2C_TYPE_MCP23008) && DISABLED(NO_LCD_DETECT)

2
Marlin/src/inc/Conditionals_post.h
Unescape Escape View File

@ -358,6 +358,8 @@
#define _LCD_CONTRAST_MAX 115 #define _LCD_CONTRAST_MAX 115
#elif ENABLED(VIKI2) #elif ENABLED(VIKI2)
#define _LCD_CONTRAST_INIT 140 #define _LCD_CONTRAST_INIT 140
#elif ENABLED(WYH_L12864)
#define _LCD_CONTRAST_INIT 190
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#define _LCD_CONTRAST_MIN 90 #define _LCD_CONTRAST_MIN 90
#define _LCD_CONTRAST_INIT 110 #define _LCD_CONTRAST_INIT 110

3
Marlin/src/inc/SanityCheck.h
Unescape Escape View File

@ -855,7 +855,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
/** /**
* LCD Lightweight Screen Style * LCD Lightweight Screen Style
*/ */
#if ENABLED(LIGHTWEIGHT_UI) && DISABLED(U8GLIB_ST7920) #if ENABLED(LIGHTWEIGHT_UI) && !IS_U8GLIB_ST7920
#error "LIGHTWEIGHT_UI requires a U8GLIB_ST7920-based display." #error "LIGHTWEIGHT_UI requires a U8GLIB_ST7920-based display."
#endif #endif
@ -2643,6 +2643,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
+ COUNT_ENABLED(MKS_TS35_V2_0, MKS_ROBIN_TFT24, MKS_ROBIN_TFT28, MKS_ROBIN_TFT32, MKS_ROBIN_TFT35, MKS_ROBIN_TFT43, MKS_ROBIN_TFT_V1_1R, ANET_ET4_TFT28, ANET_ET5_TFT35, BIQU_BX_TFT70, BTT_TFT35_SPI_V1_0) \ + COUNT_ENABLED(MKS_TS35_V2_0, MKS_ROBIN_TFT24, MKS_ROBIN_TFT28, MKS_ROBIN_TFT32, MKS_ROBIN_TFT35, MKS_ROBIN_TFT43, MKS_ROBIN_TFT_V1_1R, ANET_ET4_TFT28, ANET_ET5_TFT35, BIQU_BX_TFT70, BTT_TFT35_SPI_V1_0) \
+ COUNT_ENABLED(TFTGLCD_PANEL_SPI, TFTGLCD_PANEL_I2C) \ + COUNT_ENABLED(TFTGLCD_PANEL_SPI, TFTGLCD_PANEL_I2C) \
+ COUNT_ENABLED(VIKI2, miniVIKI) \ + COUNT_ENABLED(VIKI2, miniVIKI) \
+ ENABLED(WYH_L12864) \
+ COUNT_ENABLED(ZONESTAR_12864LCD, ZONESTAR_12864OLED, ZONESTAR_12864OLED_SSD1306) \ + COUNT_ENABLED(ZONESTAR_12864LCD, ZONESTAR_12864OLED, ZONESTAR_12864OLED_SSD1306) \
+ COUNT_ENABLED(ANET_FULL_GRAPHICS_LCD, ANET_FULL_GRAPHICS_LCD_ALT_WIRING) \ + COUNT_ENABLED(ANET_FULL_GRAPHICS_LCD, ANET_FULL_GRAPHICS_LCD_ALT_WIRING) \
+ ENABLED(AZSMZ_12864) \ + ENABLED(AZSMZ_12864) \

6
Marlin/src/lcd/dogm/marlinui_DOGM.h
Unescape Escape View File

@ -43,7 +43,7 @@
#define U8G_PARAM LCD_PINS_D4, LCD_PINS_ENABLE, LCD_PINS_RS #define U8G_PARAM LCD_PINS_D4, LCD_PINS_ENABLE, LCD_PINS_RS
#endif #endif
#elif ENABLED(U8GLIB_ST7920) #elif IS_U8GLIB_ST7920
// RepRap Discount Full Graphics Smart Controller // RepRap Discount Full Graphics Smart Controller
// and other variant LCDs using ST7920 // and other variant LCDs using ST7920
@ -72,7 +72,7 @@
#define U8G_CLASS U8GLIB_DOGM128_2X // 4 stripes (HW-SPI) #define U8G_CLASS U8GLIB_DOGM128_2X // 4 stripes (HW-SPI)
#endif #endif
#elif ENABLED(U8GLIB_LM6059_AF) #elif IS_U8GLIB_LM6059_AF
// Based on the Adafruit ST7565 (https://www.adafruit.com/products/250) // Based on the Adafruit ST7565 (https://www.adafruit.com/products/250)
@ -82,7 +82,7 @@
#define U8G_CLASS U8GLIB_LM6059_2X // 4 stripes (HW-SPI) #define U8G_CLASS U8GLIB_LM6059_2X // 4 stripes (HW-SPI)
#endif #endif
#elif ENABLED(U8GLIB_ST7565_64128N) #elif IS_U8GLIB_ST7565_64128N
// MaKrPanel, Mini Viki, Viki 2.0, AZSMZ 12864 ST7565 controller // MaKrPanel, Mini Viki, Viki 2.0, AZSMZ 12864 ST7565 controller

5
Marlin/src/lcd/dogm/u8g_dev_st7565_64128n_HAL.cpp
Unescape Escape View File

@ -63,6 +63,9 @@
#define WIDTH 128 #define WIDTH 128
#define HEIGHT 64 #define HEIGHT 64
#define PAGE_HEIGHT 8 #define PAGE_HEIGHT 8
#ifndef ST7565_XOFFSET
#define ST7565_XOFFSET 0x00
#endif
#define ST7565_ADC_REVERSE(N) ((N) ? 0xA1 : 0xA0) #define ST7565_ADC_REVERSE(N) ((N) ? 0xA1 : 0xA0)
#define ST7565_BIAS_MODE(N) ((N) ? 0xA3 : 0xA2) #define ST7565_BIAS_MODE(N) ((N) ? 0xA3 : 0xA2)
@ -123,7 +126,7 @@ static const uint8_t u8g_dev_st7565_64128n_HAL_init_seq[] PROGMEM = {
static const uint8_t u8g_dev_st7565_64128n_HAL_data_start[] PROGMEM = { static const uint8_t u8g_dev_st7565_64128n_HAL_data_start[] PROGMEM = {
U8G_ESC_ADR(0), // instruction mode U8G_ESC_ADR(0), // instruction mode
U8G_ESC_CS(1), // enable chip U8G_ESC_CS(1), // enable chip
ST7565_COLUMN_ADR(0x00), // high 4 bits to 0, low 4 bits to 0. Changed for DisplayTech 64128N ST7565_COLUMN_ADR(ST7565_XOFFSET), // high 4 bits to 0, low 4 bits to 0. Changed for DisplayTech 64128N
U8G_ESC_END // end of sequence U8G_ESC_END // end of sequence
}; };

4
Marlin/src/lcd/dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp
Unescape Escape View File

@ -29,7 +29,7 @@
#include "../../inc/MarlinConfig.h" #include "../../inc/MarlinConfig.h"
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#include "ultralcd_st7920_u8glib_rrd_AVR.h" #include "ultralcd_st7920_u8glib_rrd_AVR.h"
@ -192,5 +192,5 @@ u8g_dev_t u8g_dev_st7920_128x64_rrd_sw_spi = { u8g_dev_rrd_st7920_128x64_fn, &u8
void ST7920_write_byte(const uint8_t val) { ST7920_WRITE_BYTE(val); } void ST7920_write_byte(const uint8_t val) { ST7920_WRITE_BYTE(val); }
#endif #endif
#endif // U8GLIB_ST7920 #endif // IS_U8GLIB_ST7920
#endif // !U8G_HAL_LINKS && (__AVR__ || ARDUINO_ARCH_STM32 || ARDUINO_ARCH_ESP32) #endif // !U8G_HAL_LINKS && (__AVR__ || ARDUINO_ARCH_STM32 || ARDUINO_ARCH_ESP32)

35
Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_3.h
Unescape Escape View File

@ -222,12 +222,13 @@
#error "ANET_FULL_GRAPHICS_LCD_ALT_WIRING only applies to the ANET 1.0 board." #error "ANET_FULL_GRAPHICS_LCD_ALT_WIRING only applies to the ANET 1.0 board."
#elif ENABLED(ANET_FULL_GRAPHICS_LCD) #elif ENABLED(ANET_FULL_GRAPHICS_LCD)
#error "CAUTION! ANET_FULL_GRAPHICS_LCD requires wiring modifications. See 'pins_BTT_SKR_V1_3.h' for details. Comment out this line to continue." #error "CAUTION! ANET_FULL_GRAPHICS_LCD requires wiring modifications. See 'pins_BTT_SKR_V1_3.h' for details. Comment out this line to continue."
/** /**
* 1. Cut the tab off the LCD connector so it can be plugged into the "EXP1" connector the other way. * 1. Cut the tab off the LCD connector so it can be plugged into the "EXP1" connector the other way.
* 2. Swap the LCD's +5V (Pin2) and GND (Pin1) wires. (This is the critical part!) * 2. Swap the LCD's +5V (Pin2) and GND (Pin1) wires. (This is the critical part!)
* 3. Rewire the CLK Signal (LCD Pin9) to LCD Pin7. (LCD Pin9 remains open because this pin is open drain.) * 3. Rewire the CLK Signal (LCD Pin9) to LCD Pin7. (LCD Pin9 remains open because it is open drain.)
* 4. A wire is needed to connect the Reset switch at J3 (LCD Pin7) to EXP2 (Pin3) on the board. * 4. A wire is needed to connect the Reset switch at J3 (LCD Pin7) to EXP2 (Pin3) on the board.
* *
* !!! If you are unsure, ask for help! Your motherboard may be damaged in some circumstances !!! * !!! If you are unsure, ask for help! Your motherboard may be damaged in some circumstances !!!
@ -254,6 +255,38 @@
#define LCD_PINS_ENABLE EXP1_05_PIN #define LCD_PINS_ENABLE EXP1_05_PIN
#define LCD_PINS_D4 EXP1_07_PIN #define LCD_PINS_D4 EXP1_07_PIN
#elif ENABLED(WYH_L12864)
#error "CAUTION! WYH_L12864 requires wiring modifications. Comment out this line to continue."
/**
* 1. Cut the tab off the LCD connector so it can be plugged into the "EXP1" connector the other way.
* 2. Swap the LCD's +5V (Pin2) and GND (Pin1) wires. (This is the critical part!)
* 3. Swap the LCD's MOSI (Pin9) and empty (Pin10) wires because Pin9 is open drain.
*
* !!! If you are unsure, ask for help! Your motherboard may be damaged in some circumstances !!!
*
* The WYH_L12864 connector plug:
*
* BEFORE AFTER
* ______ ______
* GND | 1 2 | 5V 5V | 1 2 | GND
* CS | 3 4 | BTN_EN2 CS | 3 4 | BTN_EN2
* SID | 5 6 BTN_EN1 SID | 5 6 BTN_EN1
* SCK | 7 8 | BTN_ENC SCK | 7 8 | BTN_ENC
* MOSI | 9 10 | open | 9 10 | MOSI
* ------ ------
* LCD LCD
*/
#define BTN_EN1 EXP1_06_PIN
#define BTN_EN2 EXP1_04_PIN
#define BTN_ENC EXP1_08_PIN
#define DOGLCD_CS EXP1_03_PIN
#define DOGLCD_A0 EXP1_05_PIN
#define DOGLCD_SCK EXP1_07_PIN
#define DOGLCD_MOSI EXP1_10_PIN
#define LCD_BACKLIGHT_PIN -1
#elif ENABLED(CR10_STOCKDISPLAY) #elif ENABLED(CR10_STOCKDISPLAY)
#define LCD_PINS_RS EXP1_04_PIN #define LCD_PINS_RS EXP1_04_PIN

2
Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h
Unescape Escape View File

@ -323,7 +323,7 @@
/** /**
* 1. Cut the tab off the LCD connector so it can be plugged into the "EXP1" connector the other way. * 1. Cut the tab off the LCD connector so it can be plugged into the "EXP1" connector the other way.
* 2. Swap the LCD's +5V (Pin2) and GND (Pin1) wires. (This is the critical part!) * 2. Swap the LCD's +5V (Pin2) and GND (Pin1) wires. (This is the critical part!)
* 3. Rewire the CLK Signal (LCD Pin9) to LCD Pin7. (LCD Pin9 remains open because this pin is open drain.) * 3. Rewire the CLK Signal (LCD Pin9) to LCD Pin7. (LCD Pin9 remains open because it is open drain.)
* 4. A wire is needed to connect the Reset switch at J3 (LCD Pin7) to EXP2 (Pin3) on the board. * 4. A wire is needed to connect the Reset switch at J3 (LCD Pin7) to EXP2 (Pin3) on the board.
* *
* !!! If you are unsure, ask for help! Your motherboard may be damaged in some circumstances !!! * !!! If you are unsure, ask for help! Your motherboard may be damaged in some circumstances !!!

2
Marlin/src/pins/mega/pins_SILVER_GATE.h
Unescape Escape View File

@ -73,7 +73,7 @@
#define TEMP_BED_PIN 6 #define TEMP_BED_PIN 6
#if HAS_WIRED_LCD #if HAS_WIRED_LCD
#if ENABLED(U8GLIB_ST7920) // SPI GLCD 12864 ST7920 #if IS_U8GLIB_ST7920 // SPI GLCD 12864 ST7920
#define LCD_PINS_RS 30 #define LCD_PINS_RS 30
#define LCD_PINS_ENABLE 20 #define LCD_PINS_ENABLE 20
#define LCD_PINS_D4 25 #define LCD_PINS_D4 25

2
Marlin/src/pins/pins.h
Unescape Escape View File

@ -57,7 +57,7 @@
#define FET_ORDER_EFF 1 #define FET_ORDER_EFF 1
#endif #endif
#if !(BOTH(IS_ULTRA_LCD, IS_NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, MINIPANEL, REPRAPWORLD_KEYPAD)) #if !(BOTH(IS_ULTRA_LCD, IS_NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, WYH_L12864, MINIPANEL, REPRAPWORLD_KEYPAD))
#define HAS_FREE_AUX2_PINS 1 #define HAS_FREE_AUX2_PINS 1
#endif #endif

2
Marlin/src/pins/pins_postprocess.h
Unescape Escape View File

@ -1383,7 +1383,7 @@
// //
// Default DOGLCD SPI delays // Default DOGLCD SPI delays
// //
#if DISABLED(U8GLIB_ST7920) #if !IS_U8GLIB_ST7920
#undef ST7920_DELAY_1 #undef ST7920_DELAY_1
#undef ST7920_DELAY_2 #undef ST7920_DELAY_2
#undef ST7920_DELAY_3 #undef ST7920_DELAY_3

2
Marlin/src/pins/rambo/pins_EINSY_RAMBO.h
Unescape Escape View File

@ -205,7 +205,7 @@
#endif // IS_ULTIPANEL || TOUCH_UI_ULTIPANEL #endif // IS_ULTIPANEL || TOUCH_UI_ULTIPANEL
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 250 #define BOARD_ST7920_DELAY_2 250
#define BOARD_ST7920_DELAY_3 0 #define BOARD_ST7920_DELAY_3 0

2
Marlin/src/pins/rambo/pins_EINSY_RETRO.h
Unescape Escape View File

@ -201,7 +201,7 @@
#endif // HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL || TOUCH_UI_FTDI_EVE #endif // HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL || TOUCH_UI_FTDI_EVE
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 250 #define BOARD_ST7920_DELAY_2 250
#define BOARD_ST7920_DELAY_3 0 #define BOARD_ST7920_DELAY_3 0

2
Marlin/src/pins/rambo/pins_MINIRAMBO.h
Unescape Escape View File

@ -193,7 +193,7 @@
#endif // HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL #endif // HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 250 #define BOARD_ST7920_DELAY_2 250
#define BOARD_ST7920_DELAY_3 0 #define BOARD_ST7920_DELAY_3 0

2
Marlin/src/pins/rambo/pins_RAMBO.h
Unescape Escape View File

@ -270,7 +270,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 0 #define BOARD_ST7920_DELAY_2 0
#define BOARD_ST7920_DELAY_3 0 #define BOARD_ST7920_DELAY_3 0

2
Marlin/src/pins/ramps/pins_3DRAG.h
Unescape Escape View File

@ -166,7 +166,7 @@
#endif // IS_ULTRA_LCD && IS_NEWPANEL #endif // IS_ULTRA_LCD && IS_NEWPANEL
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 188 #define BOARD_ST7920_DELAY_2 188
#define BOARD_ST7920_DELAY_3 0 #define BOARD_ST7920_DELAY_3 0

2
Marlin/src/pins/ramps/pins_BQ_ZUM_MEGA_3D.h
Unescape Escape View File

@ -106,7 +106,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 0 #define BOARD_ST7920_DELAY_2 0
#define BOARD_ST7920_DELAY_3 189 #define BOARD_ST7920_DELAY_3 189

2
Marlin/src/pins/ramps/pins_DAGOMA_F5.h
Unescape Escape View File

@ -40,7 +40,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 250 #define BOARD_ST7920_DELAY_2 250
#define BOARD_ST7920_DELAY_3 250 #define BOARD_ST7920_DELAY_3 250

2
Marlin/src/pins/ramps/pins_FORMBOT_TREX2PLUS.h
Unescape Escape View File

@ -182,7 +182,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 200 #define BOARD_ST7920_DELAY_1 200
#define BOARD_ST7920_DELAY_2 200 #define BOARD_ST7920_DELAY_2 200
#define BOARD_ST7920_DELAY_3 200 #define BOARD_ST7920_DELAY_3 200

2
Marlin/src/pins/sanguino/pins_MELZI.h
Unescape Escape View File

@ -32,7 +32,7 @@
#define IS_MELZI 1 #define IS_MELZI 1
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#ifndef BOARD_ST7920_DELAY_1 #ifndef BOARD_ST7920_DELAY_1
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#endif #endif

2
Marlin/src/pins/sanguino/pins_MELZI_CREALITY.h
Unescape Escape View File

@ -36,7 +36,7 @@
#define BOARD_INFO_NAME "Melzi (Creality)" #define BOARD_INFO_NAME "Melzi (Creality)"
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#define BOARD_ST7920_DELAY_2 125 #define BOARD_ST7920_DELAY_2 125
#define BOARD_ST7920_DELAY_3 125 #define BOARD_ST7920_DELAY_3 125

2
Marlin/src/pins/sanguino/pins_MELZI_TRONXY.h
Unescape Escape View File

@ -28,7 +28,7 @@
#define BOARD_INFO_NAME "Melzi (Tronxy)" #define BOARD_INFO_NAME "Melzi (Tronxy)"
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 125 #define BOARD_ST7920_DELAY_2 125
#define BOARD_ST7920_DELAY_3 0 #define BOARD_ST7920_DELAY_3 0

2
Marlin/src/pins/sanguino/pins_MELZI_V2.h
Unescape Escape View File

@ -28,7 +28,7 @@
#define BOARD_INFO_NAME "Melzi V2" #define BOARD_INFO_NAME "Melzi V2"
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 400 #define BOARD_ST7920_DELAY_2 400
#define BOARD_ST7920_DELAY_3 0 #define BOARD_ST7920_DELAY_3 0

2
Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h
Unescape Escape View File

@ -165,7 +165,7 @@
#define KILL_PIN 10 #define KILL_PIN 10
#define BEEPER_PIN 27 #define BEEPER_PIN 27
#elif ENABLED(U8GLIB_ST7920) // SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0 #elif IS_U8GLIB_ST7920 // SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0
#if IS_MELZI #if IS_MELZI
#define LCD_PINS_RS 30 // CS chip select /SS chip slave select #define LCD_PINS_RS 30 // CS chip select /SS chip slave select

2
Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_V1_1.h
Unescape Escape View File

@ -202,7 +202,7 @@
#endif // !FYSETC_MINI_12864 #endif // !FYSETC_MINI_12864
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#define BOARD_ST7920_DELAY_2 125 #define BOARD_ST7920_DELAY_2 125
#define BOARD_ST7920_DELAY_3 125 #define BOARD_ST7920_DELAY_3 125

2
Marlin/src/pins/stm32f1/pins_CCROBOT_MEEB_3DP.h
Unescape Escape View File

@ -155,7 +155,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#define BOARD_ST7920_DELAY_2 125 #define BOARD_ST7920_DELAY_2 125
#define BOARD_ST7920_DELAY_3 125 #define BOARD_ST7920_DELAY_3 125

2
Marlin/src/pins/stm32f1/pins_FLY_MINI.h
Unescape Escape View File

@ -179,7 +179,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 715 #define BOARD_ST7920_DELAY_3 715

2
Marlin/src/pins/stm32f1/pins_GTM32_MINI.h
Unescape Escape View File

@ -158,7 +158,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 715 #define BOARD_ST7920_DELAY_3 715

2
Marlin/src/pins/stm32f1/pins_GTM32_MINI_A30.h
Unescape Escape View File

@ -166,7 +166,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 715 #define BOARD_ST7920_DELAY_3 715

2
Marlin/src/pins/stm32f1/pins_GTM32_PRO_VB.h
Unescape Escape View File

@ -163,7 +163,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 715 #define BOARD_ST7920_DELAY_3 715

2
Marlin/src/pins/stm32f1/pins_GTM32_REV_B.h
Unescape Escape View File

@ -168,7 +168,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 715 #define BOARD_ST7920_DELAY_3 715

2
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_E3_common.h
Unescape Escape View File

@ -233,7 +233,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#ifndef BOARD_ST7920_DELAY_1 #ifndef BOARD_ST7920_DELAY_1
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#endif #endif

2
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_LITE.h
Unescape Escape View File

@ -113,7 +113,7 @@
#endif // !MKS_MINI_12864 #endif // !MKS_MINI_12864
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#define BOARD_ST7920_DELAY_2 125 #define BOARD_ST7920_DELAY_2 125
#define BOARD_ST7920_DELAY_3 125 #define BOARD_ST7920_DELAY_3 125

2
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO_V2.h
Unescape Escape View File

@ -366,7 +366,7 @@
#endif #endif
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#define BOARD_ST7920_DELAY_2 125 #define BOARD_ST7920_DELAY_2 125
#define BOARD_ST7920_DELAY_3 125 #define BOARD_ST7920_DELAY_3 125

2
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_PRO.h
Unescape Escape View File

@ -300,7 +300,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#define BOARD_ST7920_DELAY_2 125 #define BOARD_ST7920_DELAY_2 125
#define BOARD_ST7920_DELAY_3 125 #define BOARD_ST7920_DELAY_3 125

2
Marlin/src/pins/stm32f1/pins_ZM3E4_V1_0.h
Unescape Escape View File

@ -332,7 +332,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#define BOARD_ST7920_DELAY_2 250 #define BOARD_ST7920_DELAY_2 250
#define BOARD_ST7920_DELAY_3 125 #define BOARD_ST7920_DELAY_3 125

2
Marlin/src/pins/stm32f1/pins_ZM3E4_V2_0.h
Unescape Escape View File

@ -305,7 +305,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 200 // Tclk_fall <200ns #define BOARD_ST7920_DELAY_1 200 // Tclk_fall <200ns
#define BOARD_ST7920_DELAY_2 250 // Tdata_width >200ns #define BOARD_ST7920_DELAY_2 250 // Tdata_width >200ns
#define BOARD_ST7920_DELAY_3 200 // Tclk_rise <200ns #define BOARD_ST7920_DELAY_3 200 // Tclk_rise <200ns

2
Marlin/src/pins/stm32f4/pins_BTT_BTT002_V1_0.h
Unescape Escape View File

@ -287,7 +287,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 600 #define BOARD_ST7920_DELAY_3 600

2
Marlin/src/pins/stm32f4/pins_BTT_E3_RRF.h
Unescape Escape View File

@ -279,7 +279,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 600 #define BOARD_ST7920_DELAY_3 600

4
Marlin/src/pins/stm32f4/pins_BTT_GTR_V1_0.h
Unescape Escape View File

@ -483,8 +483,8 @@
// Alter timing for graphical display // Alter timing for graphical display
#if IS_U8GLIB_ST7920 #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 90 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 600 #define BOARD_ST7920_DELAY_3 600
#endif #endif

2
Marlin/src/pins/stm32f4/pins_BTT_OCTOPUS_V1_common.h
Unescape Escape View File

@ -493,7 +493,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 120 #define BOARD_ST7920_DELAY_1 120
#define BOARD_ST7920_DELAY_2 80 #define BOARD_ST7920_DELAY_2 80
#define BOARD_ST7920_DELAY_3 580 #define BOARD_ST7920_DELAY_3 580

35
Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_common.h
Unescape Escape View File

@ -454,6 +454,39 @@
#define BTN_EN1 EXP2_08_PIN #define BTN_EN1 EXP2_08_PIN
#define BTN_EN2 EXP2_06_PIN #define BTN_EN2 EXP2_06_PIN
#elif ENABLED(WYH_L12864)
#error "CAUTION! WYH_L12864 requires wiring modifications. Comment out this line to continue."
/**
* 1. Cut the tab off the LCD connector so it can be plugged into the "EXP1" connector the other way.
* 2. Swap the LCD's +5V (Pin2) and GND (Pin1) wires.
*
* !!! If you are unsure, ask for help! Your motherboard may be damaged in some circumstances !!!
*
* The WYH_L12864 connector plug:
*
* BEFORE AFTER
* ______ ______
* GND | 1 2 | 5V 5V | 1 2 | GND
* CS | 3 4 | BTN_EN2 CS | 3 4 | BTN_EN2
* SID | 5 6 BTN_EN1 SID | 5 6 BTN_EN1
* SCK | 7 8 | BTN_ENC SCK | 7 8 | BTN_ENC
* MOSI | 9 10 | MOSI | 9 10 |
* ------ ------
* LCD LCD
*/
#undef BEEPER_PIN
#undef BTN_ENC
#define BTN_EN1 EXP1_06_PIN
#define BTN_EN2 EXP1_04_PIN
#define BTN_ENC EXP1_08_PIN
#define DOGLCD_CS EXP1_03_PIN
#define DOGLCD_A0 EXP1_05_PIN
#define DOGLCD_SCK EXP1_07_PIN
#define DOGLCD_MOSI EXP1_09_PIN
#define LCD_BACKLIGHT_PIN -1
#else #else
#define LCD_PINS_RS EXP1_07_PIN #define LCD_PINS_RS EXP1_07_PIN
@ -500,7 +533,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#ifndef BOARD_ST7920_DELAY_1 #ifndef BOARD_ST7920_DELAY_1
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#endif #endif

2
Marlin/src/pins/stm32f4/pins_BTT_SKR_V2_0_common.h
Unescape Escape View File

@ -482,7 +482,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#ifndef BOARD_ST7920_DELAY_1 #ifndef BOARD_ST7920_DELAY_1
#define BOARD_ST7920_DELAY_1 120 #define BOARD_ST7920_DELAY_1 120
#endif #endif

2
Marlin/src/pins/stm32f4/pins_FLYF407ZG.h
Unescape Escape View File

@ -305,7 +305,7 @@
#define FIL_RUNOUT_PIN PA3 #define FIL_RUNOUT_PIN PA3
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 715 #define BOARD_ST7920_DELAY_3 715

2
Marlin/src/pins/stm32f4/pins_FYSETC_CHEETAH_V20.h
Unescape Escape View File

@ -245,7 +245,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 600 #define BOARD_ST7920_DELAY_3 600

2
Marlin/src/pins/stm32f4/pins_FYSETC_S6.h
Unescape Escape View File

@ -314,7 +314,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 640 #define BOARD_ST7920_DELAY_3 640

2
Marlin/src/pins/stm32f4/pins_RUMBA32_common.h
Unescape Escape View File

@ -172,7 +172,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 640 #define BOARD_ST7920_DELAY_3 640

2
Marlin/src/pins/stm32f4/pins_VAKE403D.h
Unescape Escape View File

@ -183,7 +183,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 715 #define BOARD_ST7920_DELAY_3 715

Write Preview
Loading…
Cancel
Save