melch
/
Marlin
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity

Moved SLOWDOWN function. (jetty840)

Browse Source 
Included AD595 calibration options. (daid)
2.0.x
Erik van der Zalm 13 years ago
parent 4fbda5c3f5
commit 018c567abf
4 changed files with 31 additions and 50 deletions
Show Stats Download Patch File Download Diff File

43
Marlin/Configuration.h
Unescape Escape View File

@ -28,7 +28,7 @@
// Ultimaker = 7 // Ultimaker = 7
// Teensylu = 8 // Teensylu = 8
// Gen3+ =9 // Gen3+ =9
#define MOTHERBOARD 51 #define MOTHERBOARD 7
//=========================================================================== //===========================================================================
//=============================Thermal Settings ============================ //=============================Thermal Settings ============================
@ -46,13 +46,13 @@
// 6 is EPCOS 100k // 6 is EPCOS 100k
// 7 is 100k Honeywell thermistor 135-104LAG-J01 // 7 is 100k Honeywell thermistor 135-104LAG-J01
#define TEMP_SENSOR_0 1 #define TEMP_SENSOR_0 -1
#define TEMP_SENSOR_1 0 #define TEMP_SENSOR_1 0
#define TEMP_SENSOR_2 0 #define TEMP_SENSOR_2 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 0
// Actual temperature must be close to target for this long before M109 returns success // Actual temperature must be close to target for this long before M109 returns success
#define TEMP_RESIDENCY_TIME 10 // 30 // (seconds) 30 seconds was too long #define TEMP_RESIDENCY_TIME 10 // (seconds)
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // The minimal temperature defines the temperature below which the heater will not be enabled It is used
@ -71,11 +71,6 @@
#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
#define TEMP_SENSOR_AD595_OFFSET 0.0
#define TEMP_SENSOR_AD595_GAIN 1.0
// PID settings: // PID settings:
// Comment the following line to disable PID and enable bang-bang. // Comment the following line to disable PID and enable bang-bang.
@ -119,9 +114,9 @@
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins. // The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
const bool X_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops. const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
const bool Y_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops. const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops. const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0 #define X_ENABLE_ON 0
@ -135,8 +130,8 @@ const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of t
#define DISABLE_Z false #define DISABLE_Z false
#define DISABLE_E false // For all extruders #define DISABLE_E false // For all extruders
#define INVERT_X_DIR false // for Mendel set to false, for Orca set to true #define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
#define INVERT_Y_DIR true // for Mendel set to true, for Orca set to false #define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true #define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
@ -148,11 +143,11 @@ const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of t
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops false //If true, axis won't move to coordinates less than zero. #define min_software_endstops true //If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true //If true, axis won't move to coordinates greater than the defined lengths below. #define max_software_endstops true //If true, axis won't move to coordinates greater than the defined lengths below.
#define X_MAX_LENGTH 175 #define X_MAX_LENGTH 205
#define Y_MAX_LENGTH 185 #define Y_MAX_LENGTH 205
#define Z_MAX_LENGTH 90 #define Z_MAX_LENGTH 200
// The position of the homing switches. Use MAX_LENGTH * -0.5 if the center should be 0, 0, 0 // The position of the homing switches. Use MAX_LENGTH * -0.5 if the center should be 0, 0, 0
#define X_HOME_POS 0 #define X_HOME_POS 0
@ -161,7 +156,7 @@ const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of t
//// MOVEMENT SETTINGS //// MOVEMENT SETTINGS
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
#define HOMING_FEEDRATE {1500, 1500, 80, 0} // {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min) #define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min)
// default settings // default settings
@ -169,8 +164,8 @@ const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of t
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec) #define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. #define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 1500 // 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 1500 // 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts #define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts
// //
#define DEFAULT_XYJERK 20.0 // (mm/sec) #define DEFAULT_XYJERK 20.0 // (mm/sec)
@ -186,14 +181,14 @@ const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of t
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
//define this to enable eeprom support //define this to enable eeprom support
#define EEPROM_SETTINGS //#define EEPROM_SETTINGS
//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: //to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
// please keep turned on if you can. // please keep turned on if you can.
#define EEPROM_CHITCHAT //#define EEPROM_CHITCHAT
//LCD and SD support //LCD and SD support
//#define ULTRA_LCD //general lcd support, also 16x2 //#define ULTRA_LCD //general lcd support, also 16x2
//#define SDSUPPORT // Enable SD Card Support in Hardware Console #define SDSUPPORT // Enable SD Card Support in Hardware Console
//#define ULTIPANEL //#define ULTIPANEL
#ifdef ULTIPANEL #ifdef ULTIPANEL

5
Marlin/Configuration_adv.h
Unescape Escape View File

@ -59,6 +59,11 @@
#define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed #define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100 #define EXTRUDER_RUNOUT_EXTRUDE 100
//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
#define TEMP_SENSOR_AD595_OFFSET 0.0
#define TEMP_SENSOR_AD595_GAIN 1.0
//=========================================================================== //===========================================================================
//=============================Mechanical Settings=========================== //=============================Mechanical Settings===========================
//=========================================================================== //===========================================================================

13
Marlin/planner.cpp
Unescape Escape View File

@ -529,6 +529,13 @@ void plan_buffer_line(float &x, float &y, float &z, float &e, float feed_rate, u
// Enable all // Enable all
if(block->steps_e != 0) { enable_e0();enable_e1();enable_e2(); } if(block->steps_e != 0) { enable_e0();enable_e1();enable_e2(); }
// slow down when de buffer starts to empty, rather than wait at the corner for a buffer refill
int moves_queued=(block_buffer_head-block_buffer_tail + BLOCK_BUFFER_SIZE) & (BLOCK_BUFFER_SIZE - 1);
#ifdef SLOWDOWN
if(moves_queued < (BLOCK_BUFFER_SIZE * 0.5) && moves_queued > 1) feed_rate = feed_rate*moves_queued / (BLOCK_BUFFER_SIZE * 0.5);
#endif
float delta_mm[4]; float delta_mm[4];
delta_mm[X_AXIS] = (target[X_AXIS]-position[X_AXIS])/axis_steps_per_unit[X_AXIS]; delta_mm[X_AXIS] = (target[X_AXIS]-position[X_AXIS])/axis_steps_per_unit[X_AXIS];
delta_mm[Y_AXIS] = (target[Y_AXIS]-position[Y_AXIS])/axis_steps_per_unit[Y_AXIS]; delta_mm[Y_AXIS] = (target[Y_AXIS]-position[Y_AXIS])/axis_steps_per_unit[Y_AXIS];
@ -554,12 +561,6 @@ void plan_buffer_line(float &x, float &y, float &z, float &e, float feed_rate, u
if(feed_rate<minimumfeedrate) feed_rate=minimumfeedrate; if(feed_rate<minimumfeedrate) feed_rate=minimumfeedrate;
} }
// slow down when de buffer starts to empty, rather than wait at the corner for a buffer refill
int moves_queued=(block_buffer_head-block_buffer_tail + BLOCK_BUFFER_SIZE) & (BLOCK_BUFFER_SIZE - 1);
#ifdef SLOWDOWN
if(moves_queued < (BLOCK_BUFFER_SIZE * 0.5) && moves_queued > 1) feed_rate = feed_rate*moves_queued / (BLOCK_BUFFER_SIZE * 0.5);
#endif
/* /*
// segment time im micro seconds // segment time im micro seconds
long segment_time = lround(1000000.0/inverse_second); long segment_time = lround(1000000.0/inverse_second);

20
README.md
Unescape Escape View File

@ -1,23 +1,3 @@
SCUBA82's fork:
-----------------
The main goal of my fork is porting the brilliant Marlin firmware to GEN7 Boards.
I'm working on a 16MHz GEN7 board and have only tested with this configuration.
But there were reports about successfully running it at 20 MHz. Expect 25% faster moves and maybe some other issues.
Using lcd and sdcard support on an ATMega644(P) is not possible cause the sketch is way too big for its memory.
I switched to an ATMega1284P which has double size program memory. Unfortunately it's not supported in Arduino IDE out of the box but expect a tutorial on how to compile for it soon.
For the necessary pin breakouts I used Alfons3 design of GEN7 (https://github.com/Alfons3/Generation_7_Electronics) with an additional breakout for pin A0/D31.
I'll publish my desing as soon as possible.
You have to use different chip fuses to get Marlin running.
The fuses I'm using are lfuse: 0xF7 hfuse: 0xD4 efuse: 0xFD
For questions take a look into http://forums.reprap.org/read.php?181,118329 or send me an e-mail: christian_thalhammer@gmx.at
Expect this fork to be highly experimental.
WARNING: WARNING:
-------- --------
THIS IS RELEASE CANDIDATE 1 FOR MARLIN 1.0.0 THIS IS RELEASE CANDIDATE 1 FOR MARLIN 1.0.0

Write Preview
Loading…
Cancel
Save