2017-03-30 03:38:20 +02:00
/**
* Marlin 3 D Printer Firmware
* Copyright ( C ) 2016 MarlinFirmware [ https : //github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl .
* Copyright ( C ) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software : you can redistribute it and / or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation , either version 3 of the License , or
* ( at your option ) any later version .
*
* This program is distributed in the hope that it will be useful ,
* but WITHOUT ANY WARRANTY ; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE . See the
* GNU General Public License for more details .
*
* You should have received a copy of the GNU General Public License
* along with this program . If not , see < http : //www.gnu.org/licenses/>.
*
*/
/**
* Configuration_adv . h
*
* Advanced settings .
* Only change these if you know exactly what you ' re doing .
* Some of these settings can damage your printer if improperly set !
*
* Basic settings can be found in Configuration . h
*
*/
# ifndef CONFIGURATION_ADV_H
# define CONFIGURATION_ADV_H
2017-07-27 10:02:53 +02:00
# define CONFIGURATION_ADV_H_VERSION 020000
2017-03-30 03:38:20 +02:00
// @section temperature
//===========================================================================
//=============================Thermal Settings ============================
//===========================================================================
# if DISABLED(PIDTEMPBED)
# define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
# if ENABLED(BED_LIMIT_SWITCHING)
# define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
# endif
# endif
/**
* Thermal Protection protects your printer from damage and fire if a
* thermistor falls out or temperature sensors fail in any way .
*
* The issue : If a thermistor falls out or a temperature sensor fails ,
* Marlin can no longer sense the actual temperature . Since a disconnected
* thermistor reads as a low temperature , the firmware will keep the heater on .
*
* The solution : Once the temperature reaches the target , start observing .
* If the temperature stays too far below the target ( hysteresis ) for too long ( period ) ,
* the firmware will halt the machine as a safety precaution .
*
* If you get false positives for " Thermal Runaway " increase THERMAL_PROTECTION_HYSTERESIS and / or THERMAL_PROTECTION_PERIOD
*/
# if ENABLED(THERMAL_PROTECTION_HOTENDS)
# define THERMAL_PROTECTION_PERIOD 40 // Seconds
# define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
/**
* Whenever an M104 or M109 increases the target temperature the firmware will wait for the
* WATCH_TEMP_PERIOD to expire , and if the temperature hasn ' t increased by WATCH_TEMP_INCREASE
* degrees , the machine is halted , requiring a hard reset . This test restarts with any M104 / M109 ,
* but only if the current temperature is far enough below the target for a reliable test .
*
* If you get false positives for " Heating failed " increase WATCH_TEMP_PERIOD and / or decrease WATCH_TEMP_INCREASE
* WATCH_TEMP_INCREASE should not be below 2.
*/
# define WATCH_TEMP_PERIOD 20 // Seconds
# define WATCH_TEMP_INCREASE 2 // Degrees Celsius
# endif
/**
* Thermal Protection parameters for the bed are just as above for hotends .
*/
# if ENABLED(THERMAL_PROTECTION_BED)
# define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
# define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
/**
* Whenever an M140 or M190 increases the target temperature the firmware will wait for the
* WATCH_BED_TEMP_PERIOD to expire , and if the temperature hasn ' t increased by WATCH_BED_TEMP_INCREASE
* degrees , the machine is halted , requiring a hard reset . This test restarts with any M140 / M190 ,
* but only if the current temperature is far enough below the target for a reliable test .
*
* If you get too many " Heating failed " errors , increase WATCH_BED_TEMP_PERIOD and / or decrease
* WATCH_BED_TEMP_INCREASE . ( WATCH_BED_TEMP_INCREASE should not be below 2. )
*/
# define WATCH_BED_TEMP_PERIOD 60 // Seconds
# define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
# endif
# if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated.
//#define PID_EXTRUSION_SCALING
# if ENABLED(PID_EXTRUSION_SCALING)
# define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
# define LPQ_MAX_LEN 50
# endif
# endif
/**
* Automatic Temperature :
* The hotend target temperature is calculated by all the buffered lines of gcode .
* The maximum buffered steps / sec of the extruder motor is called " se " .
* Start autotemp mode with M109 S < mintemp > B < maxtemp > F < factor >
* The target temperature is set to mintemp + factor * se [ steps / sec ] and is limited by
* mintemp and maxtemp . Turn this off by executing M109 without F *
* Also , if the temperature is set to a value below mintemp , it will not be changed by autotemp .
* On an Ultimaker , some initial testing worked with M109 S215 B260 F1 in the start . gcode
*/
# define AUTOTEMP
# if ENABLED(AUTOTEMP)
# define AUTOTEMP_OLDWEIGHT 0.98
# endif
2017-06-24 21:32:48 +02:00
// Show Temperature ADC value
// Enable for M105 to include ADC values read from temperature sensors.
2017-03-30 03:38:20 +02:00
//#define SHOW_TEMP_ADC_VALUES
/**
* High Temperature Thermistor Support
*
* Thermistors able to support high temperature tend to have a hard time getting
* good readings at room and lower temperatures . This means HEATER_X_RAW_LO_TEMP
* will probably be caught when the heating element first turns on during the
* preheating process , which will trigger a min_temp_error as a safety measure
* and force stop everything .
* To circumvent this limitation , we allow for a preheat time ( during which ,
* min_temp_error won ' t be triggered ) and add a min_temp buffer to handle
* aberrant readings .
*
* If you want to enable this feature for your hotend thermistor ( s )
* uncomment and set values > 0 in the constants below
*/
// The number of consecutive low temperature errors that can occur
// before a min_temp_error is triggered. (Shouldn't be more than 10.)
//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
// The number of milliseconds a hotend will preheat before starting to check
// the temperature. This value should NOT be set to the time it takes the
// hot end to reach the target temperature, but the time it takes to reach
// the minimum temperature your thermistor can read. The lower the better/safer.
// This shouldn't need to be more than 30 seconds (30000)
//#define MILLISECONDS_PREHEAT_TIME 0
// @section extruder
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
# if ENABLED(EXTRUDER_RUNOUT_PREVENT)
# define EXTRUDER_RUNOUT_MINTEMP 190
# define EXTRUDER_RUNOUT_SECONDS 30
# define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
# define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
# endif
// @section temperature
//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
# define TEMP_SENSOR_AD595_OFFSET 0.0
# define TEMP_SENSOR_AD595_GAIN 1.0
2017-05-03 03:18:31 +02:00
/**
* Controller Fan
* To cool down the stepper drivers and MOSFETs .
*
* The fan will turn on automatically whenever any stepper is enabled
* and turn off after a set period after all steppers are turned off .
*/
//#define USE_CONTROLLER_FAN
# if ENABLED(USE_CONTROLLER_FAN)
//#define CONTROLLER_FAN_PIN FAN1_PIN // Set a custom pin for the controller fan
# define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled
# define CONTROLLERFAN_SPEED 255 // 255 == full speed
# endif
2017-03-30 03:38:20 +02:00
// When first starting the main fan, run it at full speed for the
// given number of milliseconds. This gets the fan spinning reliably
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
//#define FAN_KICKSTART_TIME 100
// This defines the minimal speed for the main fan, run in PWM mode
// to enable uncomment and set minimal PWM speed for reliable running (1-255)
// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
//#define FAN_MIN_PWM 50
// @section extruder
/**
* Extruder cooling fans
*
* Extruder auto fans automatically turn on when their extruders '
* temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE .
*
* Your board ' s pins file specifies the recommended pins . Override those here
* or set to - 1 to disable completely .
*
* Multiple extruders can be assigned to the same pin in which case
* the fan will turn on when any selected extruder is above the threshold .
*/
# define E0_AUTO_FAN_PIN -1
# define E1_AUTO_FAN_PIN -1
# define E2_AUTO_FAN_PIN -1
# define E3_AUTO_FAN_PIN -1
2017-04-06 23:45:29 +02:00
# define E4_AUTO_FAN_PIN -1
2017-03-30 03:38:20 +02:00
# define EXTRUDER_AUTO_FAN_TEMPERATURE 50
# define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
2017-08-15 14:48:10 +02:00
/**
* Part - Cooling Fan Multiplexer
2017-09-06 13:28:32 +02:00
*
2017-08-15 14:48:10 +02:00
* This feature allows you to digitally multiplex the fan output .
* The multiplexer is automatically switched at tool - change .
* Set FANMUX [ 012 ] _PINs below for up to 2 , 4 , or 8 multiplexed fans .
*/
# define FANMUX0_PIN -1
# define FANMUX1_PIN -1
# define FANMUX2_PIN -1
2017-06-02 02:17:52 +02:00
/**
* M355 Case Light on - off / brightness
*/
2017-06-03 05:02:52 +02:00
//#define CASE_LIGHT_ENABLE
# if ENABLED(CASE_LIGHT_ENABLE)
//#define CASE_LIGHT_PIN 4 // Override the default pin if needed
# define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
# define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
# define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
//#define MENU_ITEM_CASE_LIGHT // Add a Case Light option to the LCD main menu
# endif
2017-03-30 03:38:20 +02:00
//===========================================================================
//============================ Mechanical Settings ==========================
//===========================================================================
// @section homing
// If you want endstops to stay on (by default) even when not homing
// enable this option. Override at any time with M120, M121.
//#define ENDSTOPS_ALWAYS_ON_DEFAULT
// @section extras
//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
// Dual X Steppers
// Uncomment this option to drive two X axis motors.
// The next unused E driver will be assigned to the second X stepper.
//#define X_DUAL_STEPPER_DRIVERS
# if ENABLED(X_DUAL_STEPPER_DRIVERS)
// Set true if the two X motors need to rotate in opposite directions
# define INVERT_X2_VS_X_DIR true
# endif
// Dual Y Steppers
// Uncomment this option to drive two Y axis motors.
// The next unused E driver will be assigned to the second Y stepper.
//#define Y_DUAL_STEPPER_DRIVERS
# if ENABLED(Y_DUAL_STEPPER_DRIVERS)
// Set true if the two Y motors need to rotate in opposite directions
# define INVERT_Y2_VS_Y_DIR true
# endif
// A single Z stepper driver is usually used to drive 2 stepper motors.
// Uncomment this option to use a separate stepper driver for each Z axis motor.
// The next unused E driver will be assigned to the second Z stepper.
//#define Z_DUAL_STEPPER_DRIVERS
# if ENABLED(Z_DUAL_STEPPER_DRIVERS)
// Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
// That way the machine is capable to align the bed during home, since both Z steppers are homed.
// There is also an implementation of M666 (software endstops adjustment) to this feature.
// After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
// One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
// If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
// Play a little bit with small adjustments (0.5mm) and check the behaviour.
// The M119 (endstops report) will start reporting the Z2 Endstop as well.
//#define Z_DUAL_ENDSTOPS
# if ENABLED(Z_DUAL_ENDSTOPS)
# define Z2_USE_ENDSTOP _XMAX_
2017-08-03 22:26:54 +02:00
# define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 // Use M666 to determine/test this value
2017-03-30 03:38:20 +02:00
# endif
# endif // Z_DUAL_STEPPER_DRIVERS
// Enable this for dual x-carriage printers.
// A dual x-carriage design has the advantage that the inactive extruder can be parked which
// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
// allowing faster printing speeds. Connect your X2 stepper to the first unused E plug.
//#define DUAL_X_CARRIAGE
# if ENABLED(DUAL_X_CARRIAGE)
// Configuration for second X-carriage
// Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
// the second x-carriage always homes to the maximum endstop.
# define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
# define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
# define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
# define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
// However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
// override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
// without modifying the firmware (through the "M218 T1 X???" command).
// Remember: you should set the second extruder x-offset to 0 in your slicer.
// There are a few selectable movement modes for dual x-carriages using M605 S<mode>
// Mode 0 (DXC_FULL_CONTROL_MODE): Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
// as long as it supports dual x-carriages. (M605 S0)
// Mode 1 (DXC_AUTO_PARK_MODE) : Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
// that additional slicer support is not required. (M605 S1)
// Mode 2 (DXC_DUPLICATION_MODE) : Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
// actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
// once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
// This is the default power-up mode which can be later using M605.
# define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE
// Default settings in "Auto-park Mode"
# define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
# define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
// Default x offset in duplication mode (typically set to half print bed width)
# define DEFAULT_DUPLICATION_X_OFFSET 100
2017-04-15 00:21:19 +02:00
# endif // DUAL_X_CARRIAGE
// Activate a solenoid on the active extruder with M380. Disable all with M381.
// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
//#define EXT_SOLENOID
2017-03-30 03:38:20 +02:00
// @section homing
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
# define X_HOME_BUMP_MM 5
# define Y_HOME_BUMP_MM 5
# define Z_HOME_BUMP_MM 2
# define HOMING_BUMP_DIVISOR {2, 2, 4} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
// When G28 is called, this option will make Y home before X
//#define HOME_Y_BEFORE_X
// @section machine
# define AXIS_RELATIVE_MODES {false, false, false, false}
// Allow duplication mode with a basic dual-nozzle extruder
//#define DUAL_NOZZLE_DUPLICATION_MODE
// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
# define INVERT_X_STEP_PIN false
# define INVERT_Y_STEP_PIN false
# define INVERT_Z_STEP_PIN false
# define INVERT_E_STEP_PIN false
// Default stepper release if idle. Set to 0 to deactivate.
// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
// Time can be set by M18 and M84.
# define DEFAULT_STEPPER_DEACTIVE_TIME 120
# define DISABLE_INACTIVE_X true
# define DISABLE_INACTIVE_Y true
# define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
# define DISABLE_INACTIVE_E true
# define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
# define DEFAULT_MINTRAVELFEEDRATE 0.0
2017-05-17 23:16:38 +02:00
//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated
2017-03-30 03:38:20 +02:00
// @section lcd
# if ENABLED(ULTIPANEL)
# define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
# define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
# endif
// @section extras
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
# define DEFAULT_MINSEGMENTTIME 20000
// If defined the movements slow down when the look ahead buffer is only half full
# define SLOWDOWN
// Frequency limit
// See nophead's blog for more info
// Not working O
//#define XY_FREQUENCY_LIMIT 15
// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
// of the buffer and all stops. This should not be much greater than zero and should only be changed
// if unwanted behavior is observed on a user's machine when running at very slow speeds.
2017-08-03 22:26:54 +02:00
# define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
2017-03-30 03:38:20 +02:00
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
# define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
2017-04-09 13:42:54 +02:00
/**
* @ section stepper motor current
*
* Some boards have a means of setting the stepper motor current via firmware .
*
* The power on motor currents are set by :
* PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2
* known compatible chips : A4982
* DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D , RAMBO & SCOOVO_X9H
* known compatible chips : AD5206
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
* known compatible chips : MCP4728
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5 DPRINT , AZTEEG_X3_PRO , MIGHTYBOARD_REVE
* known compatible chips : MCP4451 , MCP4018
*
* Motor currents can also be set by M907 - M910 and by the LCD .
* M907 - applies to all .
* M908 - BQ_ZUM_MEGA_3D , RAMBO , PRINTRBOARD_REVF , RIGIDBOARD_V2 & SCOOVO_X9H
* M909 , M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
*/
2017-06-06 11:32:31 +02:00
//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps
//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
2017-03-30 03:38:20 +02:00
2017-04-09 10:24:49 +02:00
// Uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
2017-03-30 03:38:20 +02:00
//#define DIGIPOT_I2C
2017-10-11 22:42:24 +02:00
# if (defined(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A)) //default to settings in pins_XXXX.h files
# define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT
# define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT
# endif
/**
* common slave addresses
*
* board A ( A shifted ) B ( B shifted ) IC
* Smoothie 0x2C ( 0x58 ) 0x2D ( 0x5A ) MCP4451
* AZTEEG_X3_PRO 0x2C ( 0x58 ) 0x2E ( 0x5C ) MCP4451
* MIGHTYBOARD_REVE 0x2F ( 0x5E ) MCP4018
*/
2017-06-06 11:32:31 +02:00
//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster
2017-04-09 13:30:21 +02:00
# define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8
2017-04-09 10:24:49 +02:00
// Actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
2017-06-06 11:32:31 +02:00
# define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO
2017-03-30 03:38:20 +02:00
//===========================================================================
//=============================Additional Features===========================
//===========================================================================
# define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
# define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
# define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
# define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
// @section lcd
// Include a page of printer information in the LCD Main Menu
# define LCD_INFO_MENU
2017-05-28 18:12:12 +02:00
// Scroll a longer status message into view
//#define STATUS_MESSAGE_SCROLLING
2017-03-30 03:38:20 +02:00
// On the Info Screen, display XY with one decimal place when possible
//#define LCD_DECIMAL_SMALL_XY
// The timeout (in ms) to return to the status screen from sub-menus
//#define LCD_TIMEOUT_TO_STATUS 15000
# if ENABLED(SDSUPPORT)
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
// around this by connecting a push button or single throw switch to the pin defined
// as SD_DETECT_PIN in your board's pins definitions.
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
# define SD_DETECT_INVERTED
# define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
# define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
# define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
// if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
// using:
//#define MENU_ADDAUTOSTART
/**
* Sort SD file listings in alphabetical order .
*
* With this option enabled , items on SD cards will be sorted
* by name for easier navigation .
*
* By default . . .
*
* - Use the slowest - but safest - method for sorting .
* - Folders are sorted to the top .
* - The sort key is statically allocated .
* - No added G - code ( M34 ) support .
* - 40 item sorting limit . ( Items after the first 40 are unsorted . )
*
* SD sorting uses static allocation ( as set by SDSORT_LIMIT ) , allowing the
* compiler to calculate the worst - case usage and throw an error if the SRAM
* limit is exceeded .
*
* - SDSORT_USES_RAM provides faster sorting via a static directory buffer .
* - SDSORT_USES_STACK does the same , but uses a local stack - based buffer .
* - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM . ( Expensive ! )
* - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible . ( Use with caution ! )
*/
//#define SDCARD_SORT_ALPHA
// SD Card Sorting options
# if ENABLED(SDCARD_SORT_ALPHA)
2017-09-27 07:28:01 +02:00
# define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
2017-03-30 03:38:20 +02:00
# define FOLDER_SORTING -1 // -1=above 0=none 1=below
# define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code.
# define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
# define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
# define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
# define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
# endif
// Show a progress bar on HD44780 LCDs for SD printing
//#define LCD_PROGRESS_BAR
# if ENABLED(LCD_PROGRESS_BAR)
// Amount of time (ms) to show the bar
# define PROGRESS_BAR_BAR_TIME 2000
// Amount of time (ms) to show the status message
# define PROGRESS_BAR_MSG_TIME 3000
// Amount of time (ms) to retain the status message (0=forever)
# define PROGRESS_MSG_EXPIRE 0
// Enable this to show messages for MSG_TIME then hide them
//#define PROGRESS_MSG_ONCE
// Add a menu item to test the progress bar:
//#define LCD_PROGRESS_BAR_TEST
# endif
2017-10-15 09:15:19 +02:00
// Add an 'M73' G-code to set the current percentage
//#define LCD_SET_PROGRESS_MANUALLY
2017-03-30 03:38:20 +02:00
// This allows hosts to request long names for files and folders with M33
//#define LONG_FILENAME_HOST_SUPPORT
2017-10-19 05:15:33 +02:00
// Enable this option to scroll long filenames in the SD card menu
//#define SCROLL_LONG_FILENAMES
2017-03-30 03:38:20 +02:00
// This option allows you to abort SD printing when any endstop is triggered.
// This feature must be enabled with "M540 S1" or from the LCD menu.
// To have any effect, endstops must be enabled during SD printing.
//#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
# endif // SDSUPPORT
/**
* Additional options for Graphical Displays
*
* Use the optimizations here to improve printing performance ,
* which can be adversely affected by graphical display drawing ,
* especially when doing several short moves , and when printing
* on DELTA and SCARA machines .
*
* Some of these options may result in the display lagging behind
* controller events , as there is a trade - off between reliable
* printing performance versus fast display updates .
*/
# if ENABLED(DOGLCD)
// Enable to save many cycles by drawing a hollow frame on the Info Screen
# define XYZ_HOLLOW_FRAME
// Enable to save many cycles by drawing a hollow frame on Menu Screens
# define MENU_HOLLOW_FRAME
// A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
// Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
//#define USE_BIG_EDIT_FONT
// A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
// Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
//#define USE_SMALL_INFOFONT
// Enable this option and reduce the value to optimize screen updates.
// The normal delay is 10µs. Use the lowest value that still gives a reliable display.
//#define DOGM_SPI_DELAY_US 5
# endif // DOGLCD
// @section safety
// The hardware watchdog should reset the microcontroller disabling all outputs,
// in case the firmware gets stuck and doesn't do temperature regulation.
# define USE_WATCHDOG
# if ENABLED(USE_WATCHDOG)
// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
//#define WATCHDOG_RESET_MANUAL
# endif
// @section lcd
2017-04-13 23:26:45 +02:00
/**
* Babystepping enables movement of the axes by tiny increments without changing
* the current position values . This feature is used primarily to adjust the Z
* axis in the first layer of a print in real - time .
*
* Warning : Does not respect endstops !
*/
2017-03-30 03:38:20 +02:00
//#define BABYSTEPPING
# if ENABLED(BABYSTEPPING)
2017-09-27 07:28:01 +02:00
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
2017-09-27 06:50:09 +02:00
# define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
# define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion.
//#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
2017-04-13 23:26:45 +02:00
//#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
# define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
// Note: Extra time may be added to mitigate controller latency.
2017-09-27 07:58:46 +02:00
//#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
//#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
2017-03-30 03:38:20 +02:00
# endif
// @section extruder
/**
* Implementation of linear pressure control
*
* Assumption : advance = k * ( delta velocity )
* K = 0 means advance disabled .
* See Marlin documentation for calibration instructions .
*/
//#define LIN_ADVANCE
# if ENABLED(LIN_ADVANCE)
# define LIN_ADVANCE_K 75
/**
* Some Slicers produce Gcode with randomly jumping extrusion widths occasionally .
* For example within a 0.4 mm perimeter it may produce a single segment of 0.05 mm width .
* While this is harmless for normal printing ( the fluid nature of the filament will
* close this very , very tiny gap ) , it throws off the LIN_ADVANCE pressure adaption .
*
* For this case LIN_ADVANCE_E_D_RATIO can be used to set the extrusion : distance ratio
* to a fixed value . Note that using a fixed ratio will lead to wrong nozzle pressures
* if the slicer is using variable widths or layer heights within one print !
*
2017-04-17 07:27:49 +02:00
* This option sets the default E : D ratio at startup . Use ` M900 ` to override this value .
2017-03-30 03:38:20 +02:00
*
2017-04-17 07:27:49 +02:00
* Example : ` M900 W0 .4 H0 .2 D1 .75 ` , where :
2017-03-30 03:38:20 +02:00
* - W is the extrusion width in mm
* - H is the layer height in mm
* - D is the filament diameter in mm
*
2017-04-17 07:27:49 +02:00
* Example : ` M900 R0 .0458 ` to set the ratio directly .
*
2017-03-30 03:38:20 +02:00
* Set to 0 to auto - detect the ratio based on given Gcode G1 print moves .
*
2017-08-03 22:26:54 +02:00
* Slic3r ( including Průša Control ) produces Gcode compatible with the automatic mode .
2017-03-30 03:38:20 +02:00
* Cura ( as of this writing ) may produce Gcode incompatible with the automatic mode .
*/
# define LIN_ADVANCE_E_D_RATIO 0 // The calculated ratio (or 0) according to the formula W * H / ((D / 2) ^ 2 * PI)
// Example: 0.4 * 0.2 / ((1.75 / 2) ^ 2 * PI) = 0.033260135
# endif
// @section leveling
2017-10-18 17:03:30 +02:00
# if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
# define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
# elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
# define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
# endif
2017-03-30 03:38:20 +02:00
// Default mesh area is an area with an inset margin on the print area.
// Below are the macros that are used to define the borders for the mesh area,
// made available here for specialized needs, ie dual extruder setup.
# if ENABLED(MESH_BED_LEVELING)
2017-10-18 17:03:30 +02:00
# if ENABLED(DELTA)
// Probing points may be verified at compile time within the radius
// using static_assert(HYPOT2(X2-X1,Y2-Y1)<=sq(DELTA_PRINTABLE_RADIUS),"bad probe point!")
// so that may be added to SanityCheck.h in the future.
# define MESH_MIN_X (X_CENTER - (DELTA_PROBEABLE_RADIUS) + MESH_INSET)
# define MESH_MIN_Y (Y_CENTER - (DELTA_PROBEABLE_RADIUS) + MESH_INSET)
# define MESH_MAX_X (X_CENTER + DELTA_PROBEABLE_RADIUS - (MESH_INSET))
# define MESH_MAX_Y (Y_CENTER + DELTA_PROBEABLE_RADIUS - (MESH_INSET))
# elif IS_SCARA
# define MESH_MIN_X (X_CENTER - (SCARA_PRINTABLE_RADIUS) + MESH_INSET)
# define MESH_MIN_Y (Y_CENTER - (SCARA_PRINTABLE_RADIUS) + MESH_INSET)
# define MESH_MAX_X (X_CENTER + SCARA_PRINTABLE_RADIUS - (MESH_INSET))
# define MESH_MAX_Y (Y_CENTER + SCARA_PRINTABLE_RADIUS - (MESH_INSET))
# else
// Boundaries for Cartesian probing based on set limits
# if ENABLED(BED_CENTER_AT_0_0)
# define MESH_MIN_X (max(MESH_INSET, 0) - (X_BED_SIZE) / 2)
# define MESH_MIN_Y (max(MESH_INSET, 0) - (Y_BED_SIZE) / 2)
# define MESH_MAX_X (min(X_BED_SIZE - (MESH_INSET), X_BED_SIZE) - (X_BED_SIZE) / 2)
# define MESH_MAX_Y (min(Y_BED_SIZE - (MESH_INSET), Y_BED_SIZE) - (Y_BED_SIZE) / 2)
# else
# define MESH_MIN_X (max(X_MIN_POS + MESH_INSET, 0))
# define MESH_MIN_Y (max(Y_MIN_POS + MESH_INSET, 0))
# define MESH_MAX_X (min(X_MAX_POS - (MESH_INSET), X_BED_SIZE))
# define MESH_MAX_Y (min(Y_MAX_POS - (MESH_INSET), Y_BED_SIZE))
# endif
# endif
2017-04-09 10:15:59 +02:00
# elif ENABLED(AUTO_BED_LEVELING_UBL)
2017-10-18 17:03:30 +02:00
# if ENABLED(DELTA)
// Probing points may be verified at compile time within the radius
// using static_assert(HYPOT2(X2-X1,Y2-Y1)<=sq(DELTA_PRINTABLE_RADIUS),"bad probe point!")
// so that may be added to SanityCheck.h in the future.
# define UBL_MESH_MIN_X (X_CENTER - (DELTA_PROBEABLE_RADIUS) + UBL_MESH_INSET)
# define UBL_MESH_MIN_Y (Y_CENTER - (DELTA_PROBEABLE_RADIUS) + UBL_MESH_INSET)
# define UBL_MESH_MAX_X (X_CENTER + DELTA_PROBEABLE_RADIUS - (UBL_MESH_INSET))
# define UBL_MESH_MAX_Y (Y_CENTER + DELTA_PROBEABLE_RADIUS - (UBL_MESH_INSET))
# elif IS_SCARA
# define UBL_MESH_MIN_X (X_CENTER - (SCARA_PRINTABLE_RADIUS) + UBL_MESH_INSET)
# define UBL_MESH_MIN_Y (Y_CENTER - (SCARA_PRINTABLE_RADIUS) + UBL_MESH_INSET)
# define UBL_MESH_MAX_X (X_CENTER + SCARA_PRINTABLE_RADIUS - (UBL_MESH_INSET))
# define UBL_MESH_MAX_Y (Y_CENTER + SCARA_PRINTABLE_RADIUS - (UBL_MESH_INSET))
# else
// Boundaries for Cartesian probing based on set limits
# if ENABLED(BED_CENTER_AT_0_0)
# define UBL_MESH_MIN_X (max(UBL_MESH_INSET, 0) - (X_BED_SIZE) / 2)
# define UBL_MESH_MIN_Y (max(UBL_MESH_INSET, 0) - (Y_BED_SIZE) / 2)
# define UBL_MESH_MAX_X (min(X_BED_SIZE - (UBL_MESH_INSET), X_BED_SIZE) - (X_BED_SIZE) / 2)
# define UBL_MESH_MAX_Y (min(Y_BED_SIZE - (UBL_MESH_INSET), Y_BED_SIZE) - (Y_BED_SIZE) / 2)
# else
# define UBL_MESH_MIN_X (max(X_MIN_POS + UBL_MESH_INSET, 0))
# define UBL_MESH_MIN_Y (max(Y_MIN_POS + UBL_MESH_INSET, 0))
# define UBL_MESH_MAX_X (min(X_MAX_POS - (UBL_MESH_INSET), X_BED_SIZE))
# define UBL_MESH_MAX_Y (min(Y_MAX_POS - (UBL_MESH_INSET), Y_BED_SIZE))
# endif
# endif
2017-08-03 22:26:54 +02:00
// If this is defined, the currently active mesh will be saved in the
// current slot on M500.
# define UBL_SAVE_ACTIVE_ON_M500
2017-03-30 03:38:20 +02:00
# endif
// @section extras
2017-06-23 21:28:28 +02:00
//
// G2/G3 Arc Support
//
# define ARC_SUPPORT // Disable this feature to save ~3226 bytes
# if ENABLED(ARC_SUPPORT)
# define MM_PER_ARC_SEGMENT 1 // Length of each arc segment
# define N_ARC_CORRECTION 25 // Number of intertpolated segments between corrections
//#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles
//#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes
# endif
2017-03-30 03:38:20 +02:00
// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
//#define BEZIER_CURVE_SUPPORT
// G38.2 and G38.3 Probe Target
2017-04-14 04:06:37 +02:00
// Enable PROBE_DOUBLE_TOUCH if you want G38 to double touch
2017-03-30 03:38:20 +02:00
//#define G38_PROBE_TARGET
# if ENABLED(G38_PROBE_TARGET)
# define G38_MINIMUM_MOVE 0.0275 // minimum distance in mm that will produce a move (determined using the print statement in check_move)
# endif
// Moves (or segments) with fewer steps than this will be joined with the next move
# define MIN_STEPS_PER_SEGMENT 6
// The minimum pulse width (in µs) for stepping a stepper.
// Set this if you find stepping unreliable, or if using a very fast CPU.
# define MINIMUM_STEPPER_PULSE 0 // (µs) The smallest stepper pulse allowed
// @section temperature
// Control heater 0 and heater 1 in parallel.
//#define HEATERS_PARALLEL
//===========================================================================
//================================= Buffers =================================
//===========================================================================
// @section hidden
// The number of linear motions that can be in the plan at any give time.
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
# if ENABLED(SDSUPPORT)
# define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
# else
# define BLOCK_BUFFER_SIZE 16 // maximize block buffer
# endif
// @section serial
// The ASCII buffer for serial input
# define MAX_CMD_SIZE 96
# define BUFSIZE 4
2017-10-02 09:47:48 +02:00
// Transmission to Host Buffer Size
2017-03-30 03:38:20 +02:00
// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
// To buffer a simple "ok" you need 4 bytes.
// For ADVANCED_OK (M105) you need 32 bytes.
// For debug-echo: 128 bytes for the optimal speed.
// Other output doesn't need to be that speedy.
// :[0, 2, 4, 8, 16, 32, 64, 128, 256]
# define TX_BUFFER_SIZE 64
2017-10-02 09:47:48 +02:00
// Host Receive Buffer Size
// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
// To use flow control, set this buffer size to at least 1024 bytes.
// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048]
//#define RX_BUFFER_SIZE 1024
# if RX_BUFFER_SIZE >= 1024
// Enable to have the controller send XON/XOFF control characters to
// the host to signal the RX buffer is becoming full.
//#define SERIAL_XON_XOFF
# endif
# if ENABLED(SDSUPPORT)
// Enable this option to collect and display the maximum
// RX queue usage after transferring a file to SD.
//#define SERIAL_STATS_MAX_RX_QUEUED
// Enable this option to collect and display the number
// of dropped bytes after a file transfer to SD.
//#define SERIAL_STATS_DROPPED_RX
# endif
2017-03-30 03:38:20 +02:00
// Enable an emergency-command parser to intercept certain commands as they
// enter the serial receive buffer, so they cannot be blocked.
// Currently handles M108, M112, M410
// Does not work on boards using AT90USB (USBCON) processors!
//#define EMERGENCY_PARSER
// Bad Serial-connections can miss a received command by sending an 'ok'
// Therefore some clients abort after 30 seconds in a timeout.
// Some other clients start sending commands while receiving a 'wait'.
// This "wait" is only sent when the buffer is empty. 1 second is a good value here.
//#define NO_TIMEOUTS 1000 // Milliseconds
// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
//#define ADVANCED_OK
2017-07-22 05:43:18 +02:00
// @section extras
2017-03-30 03:38:20 +02:00
2017-07-17 22:37:36 +02:00
/**
* Firmware - based and LCD - controlled retract
*
* Add G10 / G11 commands for automatic firmware - based retract / recover .
* Use M207 and M208 to define parameters for retract / recover .
*
* Use M209 to enable or disable auto - retract .
2017-07-24 19:13:25 +02:00
* With auto - retract enabled , all G1 E moves within the set range
2017-07-17 22:37:36 +02:00
* will be converted to firmware - based retract / recover moves .
*
* Be sure to turn off auto - retract during filament change .
*
* Note that M207 / M208 / M209 settings are saved to EEPROM .
*
*/
//#define FWRETRACT // ONLY PARTIALLY TESTED
2017-03-30 03:38:20 +02:00
# if ENABLED(FWRETRACT)
2017-07-24 19:13:25 +02:00
# define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
# define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
2017-07-17 22:37:36 +02:00
# define RETRACT_LENGTH 3 // Default retract length (positive mm)
# define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
# define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)
# define RETRACT_ZLIFT 0 // Default retract Z-lift
# define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering)
# define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
# define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s)
# define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s)
2017-03-30 03:38:20 +02:00
# endif
2017-10-16 08:41:45 +02:00
/**
* Extra Fan Speed
* Adds a secondary fan speed for each print - cooling fan .
* ' M106 P < fan > T3 - 255 ' : Set a secondary speed for < fan >
* ' M106 P < fan > T2 ' : Use the set secondary speed
* ' M106 P < fan > T1 ' : Restore the previous fan speed
*/
//#define EXTRA_FAN_SPEED
2017-03-30 03:38:20 +02:00
/**
2017-05-26 20:01:02 +02:00
* Advanced Pause
* Experimental feature for filament change support and for parking the nozzle when paused .
2017-03-30 03:38:20 +02:00
* Adds the GCode M600 for initiating filament change .
2017-05-26 20:01:02 +02:00
* If PARK_HEAD_ON_PAUSE enabled , adds the GCode M125 to pause printing and park the nozzle .
2017-03-30 03:38:20 +02:00
*
* Requires an LCD display .
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT .
*/
2017-05-26 20:01:02 +02:00
//#define ADVANCED_PAUSE_FEATURE
# if ENABLED(ADVANCED_PAUSE_FEATURE)
# define PAUSE_PARK_X_POS 3 // X position of hotend
# define PAUSE_PARK_Y_POS 3 // Y position of hotend
# define PAUSE_PARK_Z_ADD 10 // Z addition of hotend (lift)
# define PAUSE_PARK_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
# define PAUSE_PARK_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
# define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
# define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
2017-03-30 03:38:20 +02:00
// It is a short retract used immediately after print interrupt before move to filament exchange position
# define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
# define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
// Longer length for bowden printers to unload filament from whole bowden tube,
// shorter length for printers without bowden to unload filament from extruder only,
// 0 to disable unloading for manual unloading
# define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
# define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
// Short or zero length for printers without bowden where loading is not used
2017-05-26 20:01:02 +02:00
# define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
# define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
2017-03-30 03:38:20 +02:00
// 0 to disable for manual extrusion
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
// or until outcoming filament color is not clear for filament color change
2017-05-26 20:01:02 +02:00
# define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
2017-03-30 03:38:20 +02:00
# define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
2017-05-26 20:01:02 +02:00
# define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
2017-03-30 03:38:20 +02:00
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
2017-06-15 04:06:34 +02:00
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
2017-03-30 03:38:20 +02:00
# endif
// @section tmc
/**
* Enable this section if you have TMC26X motor drivers .
* You will need to import the TMC26XStepper library into the Arduino IDE for this
* ( https : //github.com/trinamic/TMC26XStepper.git)
*/
//#define HAVE_TMCDRIVER
# if ENABLED(HAVE_TMCDRIVER)
//#define X_IS_TMC
//#define X2_IS_TMC
//#define Y_IS_TMC
//#define Y2_IS_TMC
//#define Z_IS_TMC
//#define Z2_IS_TMC
//#define E0_IS_TMC
//#define E1_IS_TMC
//#define E2_IS_TMC
//#define E3_IS_TMC
2017-04-09 10:23:05 +02:00
//#define E4_IS_TMC
2017-03-30 03:38:20 +02:00
# define X_MAX_CURRENT 1000 // in mA
# define X_SENSE_RESISTOR 91 // in mOhms
# define X_MICROSTEPS 16 // number of microsteps
# define X2_MAX_CURRENT 1000
# define X2_SENSE_RESISTOR 91
# define X2_MICROSTEPS 16
# define Y_MAX_CURRENT 1000
# define Y_SENSE_RESISTOR 91
# define Y_MICROSTEPS 16
# define Y2_MAX_CURRENT 1000
# define Y2_SENSE_RESISTOR 91
# define Y2_MICROSTEPS 16
# define Z_MAX_CURRENT 1000
# define Z_SENSE_RESISTOR 91
# define Z_MICROSTEPS 16
# define Z2_MAX_CURRENT 1000
# define Z2_SENSE_RESISTOR 91
# define Z2_MICROSTEPS 16
# define E0_MAX_CURRENT 1000
# define E0_SENSE_RESISTOR 91
# define E0_MICROSTEPS 16
# define E1_MAX_CURRENT 1000
# define E1_SENSE_RESISTOR 91
# define E1_MICROSTEPS 16
# define E2_MAX_CURRENT 1000
# define E2_SENSE_RESISTOR 91
# define E2_MICROSTEPS 16
# define E3_MAX_CURRENT 1000
# define E3_SENSE_RESISTOR 91
# define E3_MICROSTEPS 16
2017-04-09 10:23:05 +02:00
# define E4_MAX_CURRENT 1000
# define E4_SENSE_RESISTOR 91
# define E4_MICROSTEPS 16
2017-03-30 03:38:20 +02:00
# endif
// @section TMC2130
/**
* Enable this for SilentStepStick Trinamic TMC2130 SPI - configurable stepper drivers .
*
* You ' ll also need the TMC2130Stepper Arduino library
* ( https : //github.com/teemuatlut/TMC2130Stepper).
*
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
* the hardware SPI interface on your board and define the required CS pins
* in your ` pins_MYBOARD . h ` file . ( e . g . , RAMPS 1.4 uses AUX3 pins ` X_CS_PIN 53 ` , ` Y_CS_PIN 49 ` , etc . ) .
*/
//#define HAVE_TMC2130
# if ENABLED(HAVE_TMC2130)
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
//#define X_IS_TMC2130
//#define X2_IS_TMC2130
//#define Y_IS_TMC2130
//#define Y2_IS_TMC2130
//#define Z_IS_TMC2130
//#define Z2_IS_TMC2130
//#define E0_IS_TMC2130
//#define E1_IS_TMC2130
//#define E2_IS_TMC2130
//#define E3_IS_TMC2130
2017-04-09 10:23:05 +02:00
//#define E4_IS_TMC2130
2017-03-30 03:38:20 +02:00
/**
* Stepper driver settings
*/
# define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
# define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
# define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
2017-04-15 05:43:56 +02:00
# define X_CURRENT 1000 // rms current in mA. Multiply by 1.41 for peak current.
# define X_MICROSTEPS 16 // 0..256
2017-03-30 03:38:20 +02:00
2017-04-15 05:43:56 +02:00
# define Y_CURRENT 1000
2017-03-30 03:38:20 +02:00
# define Y_MICROSTEPS 16
2017-04-15 05:43:56 +02:00
# define Z_CURRENT 1000
2017-03-30 03:38:20 +02:00
# define Z_MICROSTEPS 16
2017-04-15 05:43:56 +02:00
//#define X2_CURRENT 1000
2017-03-30 03:38:20 +02:00
//#define X2_MICROSTEPS 16
2017-04-15 05:43:56 +02:00
//#define Y2_CURRENT 1000
2017-03-30 03:38:20 +02:00
//#define Y2_MICROSTEPS 16
2017-04-15 05:43:56 +02:00
//#define Z2_CURRENT 1000
2017-03-30 03:38:20 +02:00
//#define Z2_MICROSTEPS 16
2017-04-15 05:43:56 +02:00
//#define E0_CURRENT 1000
2017-03-30 03:38:20 +02:00
//#define E0_MICROSTEPS 16
2017-04-15 05:43:56 +02:00
//#define E1_CURRENT 1000
2017-03-30 03:38:20 +02:00
//#define E1_MICROSTEPS 16
2017-04-15 05:43:56 +02:00
//#define E2_CURRENT 1000
2017-03-30 03:38:20 +02:00
//#define E2_MICROSTEPS 16
2017-04-15 05:43:56 +02:00
//#define E3_CURRENT 1000
2017-03-30 03:38:20 +02:00
//#define E3_MICROSTEPS 16
2017-04-15 05:43:56 +02:00
//#define E4_CURRENT 1000
//#define E4_MICROSTEPS 16
/**
* Use Trinamic ' s ultra quiet stepping mode .
* When disabled , Marlin will use spreadCycle stepping mode .
*/
# define STEALTHCHOP
/**
* Let Marlin automatically control stepper current .
* This is still an experimental feature .
* Increase current every 5 s by CURRENT_STEP until stepper temperature prewarn gets triggered ,
* then decrease current by CURRENT_STEP until temperature prewarn is cleared .
* Adjusting starts from X / Y / Z / E_CURRENT but will not increase over AUTO_ADJUST_MAX
* Relevant g - codes :
* M906 - Set or get motor current in milliamps using axis codes X , Y , Z , E . Report values if no axis codes given .
* M906 S1 - Start adjusting current
* M906 S0 - Stop adjusting current
* M911 - Report stepper driver overtemperature pre - warn condition .
* M912 - Clear stepper driver overtemperature pre - warn condition flag .
*/
//#define AUTOMATIC_CURRENT_CONTROL
# if ENABLED(AUTOMATIC_CURRENT_CONTROL)
# define CURRENT_STEP 50 // [mA]
# define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
# define REPORT_CURRENT_CHANGE
# endif
/**
* The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD .
* This mode allows for faster movements at the expense of higher noise levels .
* STEALTHCHOP needs to be enabled .
* M913 X / Y / Z / E to live tune the setting
*/
//#define HYBRID_THRESHOLD
# define X_HYBRID_THRESHOLD 100 // [mm/s]
# define X2_HYBRID_THRESHOLD 100
# define Y_HYBRID_THRESHOLD 100
# define Y2_HYBRID_THRESHOLD 100
# define Z_HYBRID_THRESHOLD 4
# define Z2_HYBRID_THRESHOLD 4
# define E0_HYBRID_THRESHOLD 30
# define E1_HYBRID_THRESHOLD 30
# define E2_HYBRID_THRESHOLD 30
# define E3_HYBRID_THRESHOLD 30
# define E4_HYBRID_THRESHOLD 30
/**
* Use stallGuard2 to sense an obstacle and trigger an endstop .
* You need to place a wire from the driver ' s DIAG1 pin to the X / Y endstop pin .
* If used along with STEALTHCHOP , the movement will be louder when homing . This is normal .
*
* X / Y_HOMING_SENSITIVITY is used for tuning the trigger sensitivity .
* Higher values make the system LESS sensitive .
* Lower value make the system MORE sensitive .
* Too low values can lead to false positives , while too high values will collide the axis without triggering .
* It is advised to set X / Y_HOME_BUMP_MM to 0.
* M914 X / Y to live tune the setting
*/
//#define SENSORLESS_HOMING
# if ENABLED(SENSORLESS_HOMING)
# define X_HOMING_SENSITIVITY 19
# define Y_HOMING_SENSITIVITY 19
# endif
2017-03-30 03:38:20 +02:00
/**
* You can set your own advanced settings by filling in predefined functions .
* A list of available functions can be found on the library github page
* https : //github.com/teemuatlut/TMC2130Stepper
*
* Example :
* # define TMC2130_ADV ( ) { \
* stepperX . diag0_temp_prewarn ( 1 ) ; \
* stepperX . interpolate ( 0 ) ; \
* }
*/
# define TMC2130_ADV() { }
2017-06-03 05:02:52 +02:00
# endif // HAVE_TMC2130
2017-03-30 03:38:20 +02:00
2017-04-14 04:06:37 +02:00
// @section L6470
2017-03-30 03:38:20 +02:00
/**
* Enable this section if you have L6470 motor drivers .
* You need to import the L6470 library into the Arduino IDE for this .
* ( https : //github.com/ameyer/Arduino-L6470)
*/
//#define HAVE_L6470DRIVER
# if ENABLED(HAVE_L6470DRIVER)
//#define X_IS_L6470
//#define X2_IS_L6470
//#define Y_IS_L6470
//#define Y2_IS_L6470
//#define Z_IS_L6470
//#define Z2_IS_L6470
//#define E0_IS_L6470
//#define E1_IS_L6470
//#define E2_IS_L6470
//#define E3_IS_L6470
2017-04-09 10:23:05 +02:00
//#define E4_IS_L6470
2017-03-30 03:38:20 +02:00
# define X_MICROSTEPS 16 // number of microsteps
# define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off
# define X_STALLCURRENT 1500 // current in mA where the driver will detect a stall
# define X2_MICROSTEPS 16
# define X2_OVERCURRENT 2000
# define X2_STALLCURRENT 1500
# define Y_MICROSTEPS 16
# define Y_OVERCURRENT 2000
# define Y_STALLCURRENT 1500
# define Y2_MICROSTEPS 16
# define Y2_OVERCURRENT 2000
# define Y2_STALLCURRENT 1500
# define Z_MICROSTEPS 16
# define Z_OVERCURRENT 2000
# define Z_STALLCURRENT 1500
# define Z2_MICROSTEPS 16
# define Z2_OVERCURRENT 2000
# define Z2_STALLCURRENT 1500
# define E0_MICROSTEPS 16
# define E0_OVERCURRENT 2000
# define E0_STALLCURRENT 1500
# define E1_MICROSTEPS 16
# define E1_OVERCURRENT 2000
# define E1_STALLCURRENT 1500
# define E2_MICROSTEPS 16
# define E2_OVERCURRENT 2000
# define E2_STALLCURRENT 1500
# define E3_MICROSTEPS 16
# define E3_OVERCURRENT 2000
# define E3_STALLCURRENT 1500
2017-04-09 10:23:05 +02:00
# define E4_MICROSTEPS 16
# define E4_OVERCURRENT 2000
# define E4_STALLCURRENT 1500
2017-03-30 03:38:20 +02:00
# endif
/**
* TWI / I2C BUS
*
* This feature is an EXPERIMENTAL feature so it shall not be used on production
* machines . Enabling this will allow you to send and receive I2C data from slave
* devices on the bus .
*
* ; Example # 1
* ; This macro send the string " Marlin " to the slave device with address 0x63 ( 99 )
* ; It uses multiple M260 commands with one B < base 10 > arg
* M260 A99 ; Target slave address
* M260 B77 ; M
* M260 B97 ; a
* M260 B114 ; r
* M260 B108 ; l
* M260 B105 ; i
* M260 B110 ; n
* M260 S1 ; Send the current buffer
*
* ; Example # 2
* ; Request 6 bytes from slave device with address 0x63 ( 99 )
* M261 A99 B5
*
* ; Example # 3
* ; Example serial output of a M261 request
* echo : i2c - reply : from : 99 bytes : 5 data : hello
*/
// @section i2cbus
//#define EXPERIMENTAL_I2CBUS
# define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
2017-04-07 20:52:05 +02:00
// @section extras
/**
* Spindle & Laser control
*
* Add the M3 , M4 , and M5 commands to turn the spindle / laser on and off , and
* to set spindle speed , spindle direction , and laser power .
*
* SuperPid is a router / spindle speed controller used in the CNC milling community .
* Marlin can be used to turn the spindle on and off . It can also be used to set
* the spindle speed from 5 , 000 to 30 , 000 RPM .
*
* You ' ll need to select a pin for the ON / OFF function and optionally choose a 0 - 5 V
* hardware PWM pin for the speed control and a pin for the rotation direction .
*
* See http : //marlinfw.org/docs/configuration/laser_spindle.html for more config details.
*/
//#define SPINDLE_LASER_ENABLE
# if ENABLED(SPINDLE_LASER_ENABLE)
# define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
# define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
# define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
# define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
# define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
# define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
# define SPINDLE_INVERT_DIR false
# define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
/**
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed / power
*
* SPEED / POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
* where PWM duty cycle varies from 0 to 255
*
* set the following for your controller ( ALL MUST BE SET )
*/
# define SPEED_POWER_SLOPE 118.4
# define SPEED_POWER_INTERCEPT 0
# define SPEED_POWER_MIN 5000
# define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
//#define SPEED_POWER_SLOPE 0.3922
//#define SPEED_POWER_INTERCEPT 0
//#define SPEED_POWER_MIN 10
//#define SPEED_POWER_MAX 100 // 0-100%
# endif
2017-03-30 03:38:20 +02:00
/**
2017-04-02 21:18:59 +02:00
* M43 - display pin status , watch pins for changes , watch endstops & toggle LED , Z servo probe test , toggle pins
2017-03-30 03:38:20 +02:00
*/
//#define PINS_DEBUGGING
/**
* Auto - report temperatures with M155 S < seconds >
*/
# define AUTO_REPORT_TEMPERATURES
/**
* Include capabilities in M115 output
*/
# define EXTENDED_CAPABILITIES_REPORT
/**
* Volumetric extrusion default state
* Activate to make volumetric extrusion the default method ,
* with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter .
*
* M200 D0 to disable , M200 Dn to set a new diameter .
*/
//#define VOLUMETRIC_DEFAULT_ON
/**
* Enable this option for a leaner build of Marlin that removes all
* workspace offsets , simplifying coordinate transformations , leveling , etc .
*
* - M206 and M428 are disabled .
* - G92 will revert to its behavior from Marlin 1.0 .
*/
//#define NO_WORKSPACE_OFFSETS
2017-05-09 00:23:17 +02:00
/**
2017-05-30 08:17:22 +02:00
* Set the number of proportional font spaces required to fill up a typical character space .
* This can help to better align the output of commands like ` G29 O ` Mesh Output .
2017-05-09 00:23:17 +02:00
*
2017-05-30 08:17:22 +02:00
* For clients that use a fixed - width font ( like OctoPrint ) , leave this set to 1.0 .
* Otherwise , adjust according to your client and font .
2017-05-09 00:23:17 +02:00
*/
# define PROPORTIONAL_FONT_RATIO 1.0
2017-05-20 10:03:00 +02:00
/**
* Spend 28 bytes of SRAM to optimize the GCode parser
*/
# define FASTER_GCODE_PARSER
2017-05-28 01:49:18 +02:00
/**
* User - defined menu items that execute custom GCode
*/
//#define CUSTOM_USER_MENUS
# if ENABLED(CUSTOM_USER_MENUS)
# define USER_SCRIPT_DONE "M117 User Script Done"
2017-08-02 21:21:32 +02:00
# define USER_SCRIPT_AUDIBLE_FEEDBACK
2017-09-27 07:49:34 +02:00
//#define USER_SCRIPT_RETURN // Return to status screen after a script
2017-05-28 01:49:18 +02:00
# define USER_DESC_1 "Home & UBL Info"
# define USER_GCODE_1 "G28\nG29 W"
# define USER_DESC_2 "Preheat for PLA"
# define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
# define USER_DESC_3 "Preheat for ABS"
# define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
# define USER_DESC_4 "Heat Bed / Home / Level"
# define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
//#define USER_DESC_5 "Home & Info"
//#define USER_GCODE_5 "G28\nM503"
# endif
2017-07-02 10:44:24 +02:00
/**
* Specify an action command to send to the host when the printer is killed .
* Will be sent in the form ' //action:ACTION_ON_KILL', e.g. '//action:poweroff'.
* The host must be configured to handle the action command .
*/
//#define ACTION_ON_KILL "poweroff"
2017-06-09 20:56:32 +02:00
//===========================================================================
//====================== I2C Position Encoder Settings ======================
//===========================================================================
2017-08-03 22:26:54 +02:00
2017-06-09 20:56:32 +02:00
/**
* I2C position encoders for closed loop control .
* Developed by Chris Barr at Aus3D .
*
* Wiki : http : //wiki.aus3d.com.au/Magnetic_Encoder
* Github : https : //github.com/Aus3D/MagneticEncoder
*
* Supplier : http : //aus3d.com.au/magnetic-encoder-module
* Alternative Supplier : http : //reliabuild3d.com/
*
* Reilabuild encoders have been modified to improve reliability .
*/
//#define I2C_POSITION_ENCODERS
# if ENABLED(I2C_POSITION_ENCODERS)
# define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5
// encoders supported currently.
# define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200.
# define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. <X|Y|Z|E>_AXIS.
# define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or-
// I2CPE_ENC_TYPE_ROTARY.
# define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for
// 1mm poles. For linear encoders this is ticks / mm,
// for rotary encoders this is ticks / revolution.
//#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper
// steps per full revolution (motor steps/rev * microstepping)
//#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel.
# define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_NONE // Type of error error correction.
# define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the
// printer will attempt to correct the error; errors
// smaller than this are ignored to minimize effects of
// measurement noise / latency (filter).
# define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2.
# define I2CPE_ENC_2_AXIS Y_AXIS
# define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR
# define I2CPE_ENC_2_TICKS_UNIT 2048
//#define I2CPE_ENC_2_TICKS_REV (16 * 200)
//#define I2CPE_ENC_2_INVERT
# define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_NONE
# define I2CPE_ENC_2_EC_THRESH 0.10
# define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options
# define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below.
# define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4.
# define I2CPE_ENC_4_AXIS E_AXIS
# define I2CPE_ENC_5_ADDR 34 // Encoder 5.
# define I2CPE_ENC_5_AXIS E_AXIS
// Default settings for encoders which are enabled, but without settings configured above.
# define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR
# define I2CPE_DEF_ENC_TICKS_UNIT 2048
# define I2CPE_DEF_TICKS_REV (16 * 200)
# define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE
# define I2CPE_DEF_EC_THRESH 0.1
//#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given
// axis after which the printer will abort. Comment out to
// disable abort behaviour.
# define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault
// for this amount of time (in ms) before the encoder
// is trusted again.
/**
* Position is checked every time a new command is executed from the buffer but during long moves ,
* this setting determines the minimum update time between checks . A value of 100 works well with
* error rolling average when attempting to correct only for skips and not for vibration .
*/
# define I2CPE_MIN_UPD_TIME_MS 100 // Minimum time in miliseconds between encoder checks.
// Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise.
# define I2CPE_ERR_ROLLING_AVERAGE
# endif // I2C_POSITION_ENCODERS
2017-08-26 00:03:07 +02:00
/**
2017-08-31 18:44:43 +02:00
* MAX7219 Debug Matrix
*
* Add support for a low - cost 8 x8 LED Matrix based on the Max7219 chip , which can be used as a status
* display . Requires 3 signal wires . Some useful debug options are included to demonstrate its usage .
*
* Fully assembled MAX7219 boards can be found on the internet for under $ 2 ( US ) .
* For example , see https : //www.ebay.com/sch/i.html?_nkw=332349290049
*/
2017-08-26 00:03:07 +02:00
//#define MAX7219_DEBUG
# if ENABLED(MAX7219_DEBUG)
2017-08-31 18:44:43 +02:00
# define MAX7219_CLK_PIN 64 // 77 on Re-ARM // Configuration of the 3 pins to control the display
# define MAX7219_DIN_PIN 57 // 78 on Re-ARM
# define MAX7219_LOAD_PIN 44 // 79 on Re-ARM
2017-08-26 00:03:07 +02:00
2017-08-31 18:44:43 +02:00
/**
* Sample debug features
* If you add more debug displays , be careful to avoid conflicts !
2017-08-26 00:03:07 +02:00
*/
2017-08-31 18:44:43 +02:00
# define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning
# define MAX7219_DEBUG_STEPPER_HEAD 3 // Show the stepper queue head position on this and the next LED matrix row
# define MAX7219_DEBUG_STEPPER_TAIL 5 // Show the stepper queue tail position on this and the next LED matrix row
2017-08-26 00:03:07 +02:00
2017-08-31 18:44:43 +02:00
# define MAX7219_DEBUG_STEPPER_QUEUE 0 // Show the current stepper queue depth on this and the next LED matrix row
// If you experience stuttering, reboots, etc. this option can reveal how
// tweaks made to the configuration are affecting the printer in real-time.
2017-08-26 00:03:07 +02:00
# endif
2017-03-30 03:38:20 +02:00
# endif // CONFIGURATION_ADV_H
